Impex MWM 982 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-982
Retain This
Manual for
Reference
100621
OWNER'S
MANUAL
MARCY®MWM 982
HOME GYM
IMPEX®INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……….. 1
IMPORTANT SAFETY NOTICES...................................................................……….. 2
HARDWARE IDENTIFIER.....….....................................................................……….. 4
ASSEMBLY INSTRUCTIONS.........................................................................……….. 6
PARTS LIST…………………………………………………………………………………. 23
RESISTANCE CHART………….....................................................................……….. 24
WARRANTY...............................................................................................………….. 25
ORDERING PARTS...................................................................................………….. 25
BEFORE YOU BEGIN
Thank you for selecting the MARCY MWM-982 HOME GYM by IMPEX®INC.
For your safety and benefit, read this manual carefully before using the
machine. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are missing or
damaged parts, we guarantee you complete satisfaction through direct
assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
[email protected]
1

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Do not intend to insert weight selector pin while the weight stack or top plate
is in elevated position.
14. Be certain the weight Selector Pin is completely inserted.
15. Never use dumbbells or other means to increase the weight resistance. Use only weight
plates provided by manufacturer.
16. Keep fingers away from pinch points.
17. This machine is designed and intended for home and consumer use only, not for
commercial use.
18. Assembled Dimension: 48” x 40” x 78” (L x W x H)
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS. 2

WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are
missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the
location shown. 3

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5

ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches and
Allen Wrenches. NOTE: It is strongly recommended that this machine to be
assembled by two or more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten all Nuts and Bolts starting from this procedure until instructed
to do so.
B.) Insert the two Guide Rods (#11) into the holes on the Rear Stabilizer (#2). Secure
each Guide Rod with one M10 x 1” Allen Bolt (#64) and ¾” Washer (#73) from
the bottom. Attach two Rubber Bumpers (#28) onto the Guide Rods.
C.) Attach the Base Frame (#3) to the Rear Stabilizer. Secure them with two M10 x 4”
Carriage Bolts (#59), one U-shaped Bracket (#20), two Ø ¾” Washers (#73), and
two M10 Aircraft Nuts (#70).
D.) Attach the Vertical Frame (#4) onto the Base Frame. Secure them with two M10 x
2 3/8” Carriage Bolts (#58), one 1 ¾” x 4 ¾” Bracket (#18), two Ø ¾” Washers
(#73), and two M10 Aircraft Nuts (#70).
E.) Slide 11 Weight Plates (#50) onto the Guide Rods. Make sure the deep grooves
on the Weight Plates all face the back of the machine and downward. Align
the holes on the Weight Plates. Insert a Selector Rod (#21) through the center
hole. Slide the Selector Stem (#51) onto the Guide Rods.
F.) Use a Weight Selector Pin (#44) to select the number of Weight Plates to exercise.
Attach the ring on Weight Selector Pin’s cable onto the Selector Rod. Note: Each
Weight Plate weighs approximately 10 lbs. Please refer to the Weight
Resistance Chart in page 24.
G.) Attach the Seat Support (#5) to the Vertical Frame. Secure it with two M10 x 2 3/8”
Carriage Bolts (#58), one 1 ¾” x 4 ¾” Bracket (#18), two Ø ¾” Washers (#73), and
two M10 Aircraft Nuts (#70).
H.) Attach the Vertical Seat Support (#6) to Seat Support and Base Frame. Secure
each end of Vertical Seat Support with two M10 x 1” Allen Bolts (#64) and two Ø
¾” Washers (#73).
6

DIAGRAM 1
7

STEP 2 (See Diagram 2)
A.) Do not tighten all Nuts and Bolts until instructed to do so.
B.) Align the holes on the Upper Frame (#1) with the top of the Guide Rods (#11). Place the
Upper Frame onto the Vertical Frame (#4).
C.)Secure the Upper Frame to the Guide Rods with two M10 x 1” Allen Bolts (#64) and Ø ¾”
Washers (#73).
D.)Secure the Upper Frame to the Vertical Frame with two M10 x 2 3/8” Carriage Bolts (#58),
one 1 ¾” x 4 ¾” Bracket (#18), two ¾” Washers (#73), and two M10 Aircraft Nuts (#70).
E.) Securely tighten all Nuts and Bolts previously installed in Step-1 and Step-2.
F.) Attach the Leg Developer (#7) to the open bracket on Seat Support (#5). Secure it with one
Leg Developer Axle (#67), two M10 x 1” Allen Bolts (#64), and two Ø ¾” Washers (#73).
G.)Attach Seat Pad (#23) to Seat Support. Secure it with four M8 x 5/8” Allen Bolts (#60) and
four Ø 5/8” Washers (#72).
H.)Attach Backrest Board (#24) to Vertical Frame. Secure it with two M8 x 2 1/8” Allen Bolts
(#63) and two Ø 5/8” Washers (#72).
8

DIAGRAM 2
9

STEP 3 (See Diagram 3)
A.) Attach the Front Press Base (#8) to the Upper Frame (#1). Secure it with one 8 ½” Front Press
Axle (#19), two Ø 1” x Ø 5/8” Washers (#75), and two M10 Aircraft Nuts (#70). Do not over
tighten the Nuts.
B.) Insert the axle on the Left Butterfly (#9) through the open hole on Front Press Base from bottom.
Secure it with one Ø 1” x Ø 5/8” Washers (#75) and one M10 Aircraft Nuts (#70). Do not over
tighten the Nut. Push one large Foam Roll (#27) onto the Left Butterfly.
C.)Repeat Procedure B to install the Right Butterfly (#10).
D.)Insert the two Butterfly Lock Pins (#45) through the holes (toward the front of the equipment) on
Front Press Base into holes on Butterfly to lock the Butterflies for Front Press exercise.
E.) Pull out the Butterfly Lock Pins and insert into the storage holes (toward the back of the
equipment) on the Front Press Base for Butterfly exercise.
10

DIAGRAM 3
11

STEP 4 (See Diagram 4)
A.) Insert the Front Press Handle (#12) into the hole on Right Butterfly (#10) and Left
Butterfly (#9). Secure each Handle with one M8 x ¾” Allen Bolt (#61) and one Ø 5/8”
Curved Washer (#76).
B.) Insert 15 ¾” Long Foam Tube (#31) halfway through the hole on Seat Support (#5).
Insert 15” Short Foam Tube (#22) halfway through the hole on Leg Developer (#7).
C.)Push four Foam Rolls (#26) onto the Tubes from both ends of each Tube.
DIAGRAM 4
12

STEP 5 (See Diagram 5)
A.) Attach one Swivel Pulley Bracket (#17) to the open bracket on the back of Vertical
Frame (#4). Secure it with one M10 x 2 ½” Allen Bolt (#66), two Ø ¾” Washers (#73),
and one M10 Aircraft Nut (#70). Do not over tighten the Nut and Bolt. Make sure the
Swivel Pulley Bracket can swivel freely.
B.) Repeat Procedure A to install the other Swivel Pulley Bracket on the other side.
DIAGRAM 5
13

CABLE LOOP DIAGRAM
14

STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach the 126” Upper Cable (#32) to the front open bracket under the Upper
Frame (#1).
B.) Attach a Pulley (#35) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt
(#62), two Ø ¾” Washers (#73), and one M10 Aircraft Nut (#70).
C.) Draw the Cable towards the back of the machine to the open bracket on Vertical
Frame (#4). Repeat B to install a Pulley.
D.) Draw the Cable around the Pulley then pull back to the opening on the Front Press
Base (#8).
E.) Attach a Pulley to the opening. Secure it with one M10 x 7 ½” Allen Bolt (#68), two
Ø ¾” Washers (#73), and one M10 Aircraft Nut (#70).
F.) Draw the Cable around the Pulley then through the opening on the Vertical Frame
(#4) to the open bracket on the back of Vertical Frame. Repeat Procedure B to
install a Pulley.
G.) Draw the Cable over the Pulley and pull the Cable downwards. Attach a Pulley to
the upper hole on the two Double Floating Pulley Brackets (#13). Secure it with
one M10 x 2” Allen Bolt (#65), two Cable Retainers (#29), and one M10 Aircraft
Nut (#70). Let the Bracket hanging for now.
H.) Draw the Cable around the Pulley then pull upwards the open bracket under the
Upper Frame. Repeat Procedure B to install a Pulley.
I.) Draw the Cable downwards between the two Guide Rods (#11) to the Selector
Rod (#21). Securely thread the bolt on the end of the Cable into the Selector Rod.
15

DIAGRAM 6
16

STEP 7 (See Diagram 7& Cable Loop Diagram)
A.) Hook one end of the 98” Butterfly Cable (#34) to Right Butterfly (#10).
B.) Draw the Cable towards the right open Swivel Pulley Bracket (#17).
C.)Attach a Pulley (#35) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#62), two ¾”
Washers (#73), and one M10 Aircraft Nut (#70).
D.)Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double
Floating Pulley Bracket (#16). Repeat Procedure C to install a Pulley. Let the Bracket hang for
now.
E.) Draw the Cable around the Pulley and pull upward to the left open Swivel Pulley Bracket (#17).
Repeat C to install a Pulley.
F.) Draw the Cable over the Pulley and hook the end to the Left Butterfly (#9). DIAGRAM 7
17

STEP 8 (See Diagram 8 & Cable Loop Diagram)
A.) Attach the 164” Lower Cable (#33) to the open bracket on the Base Frame (#3).
B.) Attach a Pulley (#35) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt
(#62), two ¾” Washers (#73), and one M10 Aircraft Nut (#70).
C.) Draw the Cable underneath the Pulley then pull upward towards the Double
Floating Pulley Brackets (#13) installed in Step-6.
D.) Attach a Pulley to the selected hole on the Brackets. Secure it with one M10 x 2”
Allen Bolt (#65), two Cable Retainers (#29), and one M10 Aircraft Nut (#70).
E.) Draw the Cable around the Pulley then downward to an open bracket on Base
Frame. Repeat B to install a Pulley.
F.) Draw the Cable around the Pulley and pull the Cable upward to the Angled
Double Floating Pulley Brackets (#16) previously installed in Step-7. Repeat B to
install a Pulley.
G.) Draw the Cable around the Pulley and downward to the open bracket on Base
Frame. Repeat Procedure B to install another Pulley.
H.) Draw the Cable underneath the Pulley through the opening on Vertical Frame
(#4) to the opening on Vertical Seat Support (#6). Attach a Pulley to the opening.
Secure it with one M10 x 2 ½” Allen Bolt (#66), two Ø 1” x Ø 5/8” Pulley Bushings
(#57), and one M10 Aircraft Nut (#70).
I.) Draw the Cable underneath the Pulley to the bracket on the Leg Developer (#7).
Secure the end of Cable to the bracket with one M10 x 1” Allen Bolt (#64), two Ø
¾” Washers (#73), and one M10 Aircraft Nut (#70).
J.) If the whole Cable system is too loose, adjust the tension of the cable system by
moving up or down the lower pulley on the Double Floating Pulley Bracket.
Moving up the pulley up will increase the tension in the pulley system;
conversely, lowering the pulley will decrease the tension.
18

DIAGRAM 8
19