Impex MARCY MWM 1801 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM 1801
Retain This
Manual for
Reference
08-18-03
OWNER'S
MANUAL
MARCY HOME GYM
MWM 1801
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……….. 1
IMPORTANT SAFETY NOTICES...................................................................……….. 2
HARDWARE PACK……….....….....................................................................……….. 3
ASSEMBLY INSTRUCTIONS.........................................................................……….. 5
HOW TO USE..................................................................................................………. 25
PARTS LIST…………………………………………………………………………………..26
RESISTANCE CHART………….......................................................................………. 27
WARRANTY.................................................................................................…………. 28
ORDERING PARTS.......................................................................................…………28
BEFORE YOU BEGIN
Thank you for selecting the MARCY MWM 1801 HOME GYM by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed to
provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOO-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
[email protected]m
1

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF
THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

HARDWARE PACK
3

HARDWARE PACK
4

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended this machine to be assembled by two or more people to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Left Base Frame (#3) to the Right Base Frame (#1). Secure them with one Bracket
(#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅¾” Washers (#93), and two M10 Aircraft
Nuts (#90).
DIAGRAM 1
5

STEP 2 (See Diagram 2)
A.) Attach the Right Vertical Beam (#2) to the Right Base Frame (#1). Secure it with two M10
x 2 ½” Carriage Bolts (#82), ∅¾” Washers (#93), and M10 Aircraft Nuts (#90). NOTE:
Do not tighten the Nuts and Bolts yet.
B.) Attach the Right Seat Support (#8) to the Right Base Frame (#1). Secure it with one M10
x 2 ½” Carriage Bolt (#82), ∅¾” Washer (#93), and M10 Aircraft Nut (#90).
C.)Attach the Right Seat Support (#8) to the Right Vertical Beam (#2). Secure it with one
Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅¾” Washers (#93), and two
M10 Aircraft Nuts (#90).
D.)Attach the Leg Developer (#9) to the Right Seat Support (#8). Secure it with one M10 x 2”
Axle (#56), two M10 x ¾” Allen Bolts (#86), and two ∅¾” Washers (#93). NOTE: Do not
over tighten the bolts. Make sure the Leg Developer is able to swivel.
DIAGRAM 2
6

STEP 3 (See Diagram 3)
A.) Align four ∅2 ½” x 1” Rubber Bumpers (#68) to the holes on the Right Base Frame
(#1). Insert four Guide Rods (#5) through the Rubber Bumpers into the holes on the
Right Base Frame. Slide two Selector Stems (#35) onto the Guide Rods. Insert a
Selector Rod (#24) through the hole on each Selector Stem. Secure each Selector
Rod to the Selector Stem with two M10 x 1” Allen Bolts (#78) and ∅¾” Washers
(#93). Please note this machine comes with 18 plates, 9 to each stack. You can
purchase another 5 more plates (Model no. WK51) in the future to increase the
weights. It is strongly recommended to spay lubricant such as WD-40 on the two
Guide Rods to minimize friction.
B.) Attach the Right Upper Frame (#6) to the top of Right Vertical Beam (#2). Secure it
with a Pulley Bracket (#46), two M10 x 2 ½” Carriage Bolts (#82), two Ø ¾” Washers
(#93), and two M10 Aircraft Nuts (#90).
C.) Attach the Top Socket Assembly (#7) to the four Guide Rods. Make sure the Guide
Rods are inserted into the holes on the Top Socket Assembly. Secure the Top Socket
Assembly to the Guide Rods with four M10 x 1” Allen Bolts (#78) and ∅¾” Washers
(#93).
D.) Secure the Top Socket Assembly (#7) to the Right Upper Frame (#6) with two M10 x
2 3/8” Carriage Bolts (#80), ∅3/4” Washers (#93) and M10 Aircraft Nuts (#90).
E.) Carefully tilt over the machine with a help of another person. Secure the Guide Rods
(#5) to the Right Base Frame (#1) with four ∅¾” Washers (#93) and M10 x 1” Allen
Bolts (#78).
F.) Securely tighten all Nuts and Bolts previously installed.
7

DIAGRAM 3
8

STEP 4 (See Diagram 4)
A.) Attach the Left Vertical Beam (#4) to the Left Base Frame (#3). Secure it with two
M10 x 2 ½” Carriage Bolts (#82), ∅¾” Washers (#93), and M10 Aircraft Nuts (#90).
B.) Attach the Left Upper Frame (#11) to the Top Socket Assembly (#7) and the Left
Vertical Beam. Secure the Frame to the Left Vertical Beam with one Bracket (#47),
two M10 x 2 ½” Carriage Bolts (#82), two ∅¾” Washers (#93), and two M10 Aircraft
Nuts (#90). Secure the Frame to the Top Socket Assembly with one Bracket (#47),
two M10 x 2 ½” Carriage Bolts (#82), two ∅¾” Washers (#93), and two M10 Aircraft
Nuts (#90).
C.) Attach the Left Seat Support (#14) to the Left Base Frame (#3) and the Left Vertical
Beam (#4). Secure it to the Left Base Frame with one M10 x 2 ½” Carriage Bolt
(#82), ∅¾” Washer (#93), and M10 Aircraft Nut (#90). Secure it to the Vertical
Beam with one Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅¾”
Washers (#93), and two M10 Aircraft Nuts (#90).
D.) Attach the Leg Press Frame (#17) to the bracket on the Left Base Frame (#3).
Secure it with one M12 x 3” Allen Bolt (#77), two ∅1” Washers (#92), and one M12
Aircraft Nut (#89). Do not over tighten the Nut and Bolt. Make sure the Leg Press
Frame is able to swivel.
E.) Attach the Leg Press Support Frames (#18) to both side of the Leg Press Frame
(#17). Secure them together with two M10 x 2 ½” Carriage Bolts (#82), ∅¾”
Washers (#93), and M10 Aircraft Nuts (#90).
9

DIAGRAM 4
10

STEP 5 (See Diagram 5)
A.) Attach the Front Press Base (#15) to the Left Base Frame (#3). Secure it with a
M10 x 9 ¼” Axle (#50), two ∅¾” Washers (#93), and two M10 Aircraft Nuts (#90).
B.) Attach the two Front Presses (#16) to the Front Press Base (#15). Secure each
Front Press with two M10 x 2 ½” Carriage Bolts (#82), two ∅¾” Washers (#93),
and two M10 Aircraft Nuts (#90). DIAGRAM 5
11

STEP 6 (See Diagram 6)
A.) Insert the axle on the Left Butterfly (#12) through the hole on the Left Upper Frame
(#11) from the bottom up. Slide a ∅1 ½” Washer (#54) and ∅1 3/8” Lock Ring (#53)
onto the Axle. Align the holes and secure the Ring with a M6 x 1 5/8” Hex Bolt (#87)
and M6 Aircraft Nut (#91). Repeat the same procedure to install the other side.
B.) Push two Butterfly Foam Rolls (#39) onto the Butterfly arms.
DIAGRAM 6
12

Cable Loop Diagram for Butterfly Station
13

Cable Loop Diagram for Bench Press Station
14

STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the two Swivel Pulley Brackets (#42) to the Left Upper Frame (#11). Secure each
Bracket with one M12 x 4 3/8” Allen Bolt (#76), two ∅1” Washers (#92) and one M12 Aircraft
Nut (#89). NOTE: Do not over tighten the Bolt. Make sure the Bracket is able to swivel.
B.) Attach one end of the 83” Butterfly Cable (#29) to the clip on the Right Butterfly (#13). Pull
the Cable to the right open Swivel Pulley Bracket (#42).
C.)Attach a Pulley (#65) to the Bracket. Secure it with one M10 x 2 “Allen Bolt (#81), two ∅¾”
Washers (#93), and one M10 Aircraft Nut (#90).
D.)Draw the Cable downward. Repeat Step B above to install a Pulley to the Angled Double
Pulley Bracket (#45). Let the Bracket hanging for now. Pull the Cable upward to the left
open Swivel Pulley Bracket.
E.) Repeat Step B above to install another Pulley to the Left Swivel Pulley Bracket. Draw the
Cable to the Left Butterfly (#12). Attach the end of the Cable to the clip on the Left Butterfly.
DIAGRAM 7
15

STEP 8 (See Diagram 8 & Cable Loop Diagram)
A.) Attach a Chain (#51) to the Left Vertical Beam (#4). Secure it with one M10 x 1 3/8”
Allen Bolt (#83), two ∅3/4” Washers (#93), and one M10 Aircraft Nut (#90). Attach one
end of the 136” Butterfly Support Cable (#31) to the Chain using a C-clip (#63). NOTE:
After complete installing all the cables, check the tightness of the cable loop system. If
the cable is too loose, shorten the chain.
B.) Draw the Cable to the Angled Double Pulley Bracket (#45) previously installed.
C.) Attach a Pulley to the Bracket. Secure it with one M10 x 2” Allen Bolt (#81), two ∅¾”
Washers (#93), and one M10 Aircraft Nut (#90).
D.) Pull the Cable around the Pulley then downward. Repeat Step C above to install a
Pulley to a Single Floating Pulley Bracket (#43). Let the Bracket hanging for now. Draw
the Cable underneath the Pulley then upward through the Left Upper Frame (#11) to
the open Bracket on the top.
E.) Attach a U-shaped Bracket (#49) to the Bracket. Repeat Step C above to install a
Pulley. Draw the Cable over the Pulley then pull the Cable downward to the Selector
Rod (#24). Thread the tip bolt of the Cable into the Selector Rod.
16

STEP 9 (See Diagram 9 & Cable Loop Diagram)
A.) Attach one end of the140” Leg Press Cable (#28) to the opening hole on the Left Seat
Support (#14), underneath the rubber bumper. Secure it with one M10 x 2 3/8” Allen
Bolt (#79), two ∅¾” Washers (#93), and one M10 Aircraft Nut (#90).
B.) Draw the Cable to the slotted opening on the Leg Press Frame (#17). Install a Pulley to
the opening then secure it with two ∅5/8” x ½” Pulley Bushings (#58), one M10 x 2 3/8”
Allen Bolt (#79), and one M10 Aircraft Nut (#90).
C.)Draw the Cable around the Pulley then toward the opening on the Left Seat Support
(#14). Repeat the Step B above to install a Pulley.
D.)Draw the Cable over the Pulley then downward to the open bracket on the Left Base
Frame (#3). Attach a Pulley to the Bracket then secure it with one M10 x 2” Allen Bolt
(#81), two ∅¾” Washers (#93), and one M10 Aircraft Nut (#90).
E.) Draw the Cable underneath the Pulley and towards the back of the machine, along the
Left Base Frame to the lower opening on the Left Vertical Beam (#4). Repeat Step B
above to install a Pulley. Draw the Cable around the Pulley then pull back towards the
lower opening on the Front Press Base (#15).
F.) Attach a Pulley to the opening. Secure it with one M10 x 8 ¼” Allen Bolt (#75), two ∅¾”
Washers (#93), and one M10 Aircraft Nut (#90).
G.)Draw the cable around the Pulley then pull the Cable towards the open bracket on the
Left Vertical Beam. Attach a U-shaped Bracket (#49) to the open Bracket. Install
another Pulley. Secure them with one M10 x 2” Allen Bolt (#81), two ∅¾” Washers
(#93), and one M10 Aircraft Nut (#90).
H.)Draw the Cable around the Pulley then back to the upper opening on the Front Press
Base (#15). Repeat Step F above to install another Pulley.
I.) Draw the Cable around the Pulley then towards the upper slotted opening on the Left
Vertical Beam (#4). Repeat Step B above to install a Pulley.
J.) Draw the Cable over the Pulley then downward to the open bracket on the Left Base
Frame. Install a Pulley. Secure the Pulley with an L-shaped Bracket (#48), one M10 x 2”
Allen Bolt (#81), two ∅¾” Washers (#93), and one M10 Aircraft Nut (#90).
K.) Draw the Cable underneath the Pulley then pull the Cable upward to the Single Floating
Pulley Bracket (#43) previously installed. Secure the Cable with one M10 x 1 3/8”” Allen
Bolt (#83), two ∅¾” Washers (#93), and one M10 Aircraft Nut (#90).
17

DIAGRAM 9
18

STEP 10 (See Diagram 10 & Cable Loop Diagram)
A.) Attach the 114” Upper Cable (#26) to the front opening on the Right Upper Frame (#6).
NOTE: The Ball Stopper on the Cable needs to be underneath the Frame.
B.) Attach a Pulley (#65) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅
5/8” x ½” Pulley Bushings (#58), and one M10 Aircraft Nut (#90).
C.)Draw the Cable towards the back of the machine to the Pulley Bracket (#46). Install a Pulley
to the Bracket. Secure it with one M10 x 2” Allen Bolt (#81), one L-shaped Bracket (#48), two
∅¾” Washers (#93), and one M10 Aircraft Nut (#90).
D.)Pull the Cable over the Pulley then downward. Attach a Pulley to a Double Floating Pulley
Bracket (#44). Secure it with one M10 x 2” Allen Bolt (#81), two ∅¾” Washers (#93), and
one M10 Aircraft Nut (#90). Let the Bracket hanging for now.
E.) Pull the Cable around the Pulley then upward to the open bracket on the back of the Top
Socket Assembly (#7). Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt
(#81), U-shaped Bracket (#49), two ∅¾” Washers (#93), and one M10 Aircraft Nut (#90).
F.) Pull the Cable around the Pulley then downward to the Selector Rod (#24). Thread the bolt
at the end of the Cable into the Selector Rod.
19