IMS
Frame Counting Sensor
Control output circuit diagram（NPN）
*(1) ：Accuracy refers to the smallest particle size to achieve no blind area detection；
*(2) ：Non-standard structure can be designed.
Model CX3068 CX6080
Accuracy
*(3)
100mA Max.
0~20ms
0~50ms
NPN（PNP type can be customized）Output
Circuit protection
Response time
Parameter
adjustment
Power supply
Sensing area*(2)
Connection
Current consumption
Load current
Line
color
definition
Protection degree
Weight
Single channel
Accessory
M8 connector, 4P M12 connector, 7P
40mA 90mA 70mA
DC10~30V（including voltage ripple of 10%(p-p)max.）*(4)
Operation: black; Alarm: red or white
Power: brown; ground: blue
Instruction, screwdriver
IEC IP64
414g
223g 395g 558g
Four channels*(1)
28*68 57.6*91.5 87*147 20*50
φ3mm φ3/φ5mm φ4mm
φ1.5/φ5mm
EX6080 CX90150
60.6*80
φ1.5/φ5mm
Individual
Common
Material
Case: aluminum, Black anode
Power on delay, power supply reverse polarity protection, output
short-circuit protection, output reverse polarity protection
1ms1.6ms
Indicators
Power indicator
(
green
)
, operation indicator
(
red
)
, Alarm
(
yellow
)
Ambient illumination
Ambient temperature
Ambient humidity
Incandescent lamp: Max. 5,000lx /Sunlight: Max. 50,000lx
Operation: -20～65 ℃; Storage: -30～80 ℃（with no icing and
condensation）
Operation: 45～85 %RH; Storage: 35%～95%RH (with no condensation)
Operation: black, white,
red, green; Alarm: yellow
*(1): The product has 26mm and 30mm channel spacing, which can be expanded into 8
channels and 12 channels；*(2): Effective areas for material testing should be large enough
to ensure that no collision or overlap occurs in the area；*(3): Minimum material size without
leakage or miscounted in sensing area；*(4): Customizable 5V low-power products for
battery-powered outdoor environments.
Non
Alarm output
A
CX 30 68 Tn Vn 3NF
Reset time
O
Fixing
On-delay function
A
Response time
Item
*(2)
Number Unit：mm
Vn Channel spacing
nNumber,4、6、8...
Number Unit：mm
Number Unit：mm
V：Channel spacing ，n：number（mm）
Tn：channel number,no need to fill in single channel
Length of sensing area,no need to fill in the ring series
Width of sensing area
Accuracy/Sensitivity
*(1)
Output
CX
RX
EX
Frame series
Ring series
Slot series
PG Miniature
Fixing
Off-delay functionF
NPN
PNPP
N
O
Alarm
INSTRUCTION MANUAL
! WARNING
! CAUTION
Thank for you selecting IMS product.This sheet primarily describes precautions
required in installing and operating the product.Before operating the product,read
the sheet thoroughly to acquire sufficient knowledge of the product.For your
convenience,keep the sheet at your disposal.
Failure to follow these instructions may result in serious injury or death：
Fail-safe device must be installed when using the unit with machinery that may
cause serious injury or substantial economic loss. (e.g. nuclear power control,
medical equipment, ships, vehicles, railways, aircraft, combustion apparatus,
safety equipment, crime/disaster prevention devices,etc.)
Failure to follow these instructions may result in product damage：
Do not use this unit over rated voltage；
Do not use this unit where there is flammable or explosive gas；
Do not use this unit where there is vibration or impact；
In cleaning the unit, do not use water or an oil-based detergent.
Features
Ordering information
Suitable for all types of materials, metal or non-metal
Fast Response time, down to 1ms
On-delay、Off-delay can be set
High performance ASIC with high immunity to EMI and environmental
interference
Built in algorithm to calculate the volume of passing object
Strong metal structure with M8 connector
Specifications
On-delay
Off-delay
Four channels
Alarm
indicator
(yellow)
Load
Brown（+）+V
10~30VDC
+
-
White/Green/Black/Red
（OUT）output
Blue（- ）0V
Load
Yellow（ALARM）output
Operation
indicator
(red)
Main circuit
主
电
路
短路保护
黑色 ： 动作输出 NPN
白色 ： 稳定输出 NPN
棕色 ： 12 ~ 30 VDC
①
②
③
④蓝色 ： GND
电源指示灯
动作指示灯
上电调节及警报指示灯
Power
indicator
(green)
Operation
indicator
(red)
Alarm indicator
(yellow)
Main
circuit
Short circuit
protection
Black：Operation
output NPN
White：Stability
output NPN
Blue：GND
Brown：10~30VDC
Parameter adjustement
Max Max
