INAPOD Office Pod Series User manual

ASSEMBLY DIAGRAM

INSTALLATION MANUAL
PHONE BOOTH SERIES
D POD
ATTENTION
Please read this instruction carefully and check all the parts before assembly.
Please be careful during the assembly to prevent hurting or damage of product.

1
Leveling tool
DETAIL : (A)
BASE FRAME
DETAIL : (A)
Adjustable foot cap for leveling
Push to final position
before setting up the booth
Level the base before installation
Step 1
Step 2
Step 3
Adjustable Foot Cap
x10 pcs

2
REINFORCE 'L' BRACKET
DETAIL : (B)
DETAIL : (B)
Do not tighten
Cap screw with flat washer
(m8 x 20zp)

3
LEFT PANEL
RIGHT PANEL
DETAIL : (C)
Do not tighten
Cap screw with flat washer
(m8 x 20zp)

4
DETAIL : (D)
DETAIL : (E)
Cap screw with flat washer
(m5 x 16zp)
Rear
Top Support
Rear
Bottom Support
DETAIL : (D)
DETAIL : (E)
SPECIAL TOOL
SPECIAL TOOL
REAR VIEW

DETAILS
TOP PANEL
TOP PANEL
STEP 1
STEP 2
STEP 3
VENTILATION FAN
TOP PANEL
Pan head screw
(m4 x 12)
5
TOP PANEL
STEP 1 STEP 2 STEP 3
Rear Glass
Top Panel Rear
Top Support
Rear Glass
Top Panel Rear
Top Support
Rear Glass
Top Panel Rear
Top Support

REAR GLASS RUBBER SEAL
(1990mm x 2pcs)
REAR GLASS
(x2pcs)
REAR GLASS 'I' JOINT
(2025mm x 1pc)
REAR GLASS RUBBER SEAL
(2018mm x 1pc)
GLASS HOLDER BRACKET
(395mm x 15pcs)
6

DETAIL : (G)
DETAIL : (F)
Do not tighten
REAR GLASS
REAR GLASS
'I' JOINT
DETAIL : (F)
DETAIL : (G)
7
Pan head screw
(m4 x 12)
Cap screw
with flat washer
(m8 x 20zp)
STEP 1 STEP 2 STEP 3
STEP 4 STEP 5
REAR GLASS REAR GLASS RUBBER SEAL
(2018mm x 1pc) GLASS HOLDER BRACKET
(395mm x 5pcs)
REAR GLASS RUBBER SEAL
(1990mm x 2pcs) REAR GLASS HOLDER BRACKET
(395mm x 10pcs)
Do not tighten

Check Leveling
Tighten all screw to ensure steady structure
90°
90°
90°
90°
2032mm
8DETAIL : (H)
DETAIL : (I)
DETAIL : (J)
DETAIL : (K)
DETAIL : (H,I,J & K)
DETAIL : (H) DETAIL : (I) DETAIL : (J)
DETAIL : (K)
STEP 1
STEP 2

908mm
9
DETAIL : (L)
DETAIL : (L)
Cap screw with flat washer
(m8 x 20zp)
ALU FIXED GLASS (L)
ALU FIXED GLASS (R)
Cap screw with flat washer
(m8 x 20zp)

10
GLASS SWING DOOR

11
Pan Head Shelf Drilling Screw
(XR ZP #8 X 1/2")
DETAIL : (M)
Pan Head Shelf Drilling Screw
(XR ZP #8 X 1/2")
DETAIL : (M)

12
DETAIL : (N)
SCREW
COVER
SCREW
HANDLE
SHAFT
COVER
HANDLE
SCREW
GLASS PROTECTION NYLON
DOOR LATCH HANDLE
DETAIL : (N)

INCOMING SUPPLY
SENSOR
LED LIGHT
VENTILATION FAN 1
CONTROL BOX
SOCKET OUTLET
VENTILATION FAN 2
DETAIL : (O)
DETAIL : (O)
VENTILATION FAN 2
LED LIGHT STRIP
6W SPLITTER
3W SPLITTER RF RECEIVER
"LEARNING KEY"
Before the first use,please open the battery
cover and remove the *protective film*
PAIR WITH RF RECEIVER
1- Click "learning key" on RF receiver
2- Click ON or OFF button on RF remote
3- LED lights connected with the receiver will
flicker once
4- The receiver is paired with remote successfully
HOW TO DELETE THE PAIRING
1- Press and hold down "learning key" on the
RF receiver for over 3 seconds until connected
LED lights flicker twice, which means the pairing
deleted successfully.
VENTILATION FAN 1
RF REMOTE
(REMOVE)
*PROTECTIVE FILM*
BATTERY COVER
BATTERY CR2430
13

1
2
3
5
TOP PANEL INTERNAL COVER
WITH LAMP HOLE
(Acoustic Board)
TOP PANEL INTERNAL COVER
(Acoustic Board)
RIGHT PANEL
INTERNAL COVER
(Acoustic Board)
LEFT PANEL INTERNAL COVER
(Acoustic Board)
Cap screw with flat washer
(m5 x 16zp)
14
BASE CARPET BOARD
x2pcs
4
1

DETAIL : (P)
DETAIL : (P)
SENSOR
SOCKET OUTLET
SENSOR
SOCKET OUTLET
SENSOR
SOCKET OUTLET
Cap screw with flat washer
(m8 x 20zp) JCBC SCREW
(m6 x 16 ZP)
TABLE POLE
TABLE POLE
COVER
TABLE SUPPORT
TABLE TOP
15

SIDE STEP
FLOOR RUBBER SEAL
(2000mm x 1pc)
ALU FIXED GLASS SEAL
(2000mm x 2pcs)
S/S A2 CSK HD MC SCREW
(m5 x 12)
16

17
SOFA
x2pcs