INAPOD PHONE BOOTH Series User manual

ASSEMBLY DIAGRAM

INSTALLATION MANUAL
PHONE BOOTH
SERIES W POD
�ATTENTION





TOP PANEL
LEFT PANEL
RIGHT PANEL
REAR
TOP SUPPORT
REAR GLASS
REAR
BOTTOM
SUPPORT
REINFORCE 'L' BRACKET
GLASS SWING DOOR
DOOR LATCH
HANDLE
BASE
CARPET BOARD
TABLE SET

1
Leveling tool
DETAIL : (A)
BASE FRAME
DETAIL : (A)
Adjustable foot cap for leveling
Push to final position
before setting up the booth
Level the base before installation
Step 1
Step 2
Step 3
Adjustable Foot Cap
x10 pcs

2
REINFORCE 'L' BRACKET
DETAIL : (B)
DETAIL : (B)
Do not tighten
Cap screw with flat washer
(m8 x 20zp)

3
LEFT PANEL
RIGHT PANEL
DETAIL : (C)
Do not tighten
Cap screw with flat washer
(m8 x 20zp)
DETAIL : (C)

4
DETAIL : (D)
DETAIL : (E)
Cap screw with flat washer
(m5 x 16zp)
Rear
Top Support
Rear
Bottom Support
DETAIL : (D)
DETAIL : (E)
SPECIAL TOOL
SPECIAL TOOL
REAR VIEW

DETAILS
TOP PANEL
TOP PANEL
STEP 1
STEP 2
STEP 3
Pan head screw
(m4 x 12)
5
TOP PANEL
STEP 1 STEP 2 STEP 3
Rear Glass
Top Panel Rear
Top Support
Rear Glass
Top Panel Rear
Top Support
Rear Glass
Top Panel Rear
Top Support

REAR GLASS RUBBER SEAL
(1990mm x 2pcs)
REAR GLASS
(x2pcs)
REAR GLASS 'I' JOINT
(2025mm x 1pc)
REAR GLASS RUBBER SEAL
(1618mm x 1pc)
GLASS HOLDER BRACKET
(395mm x 15pcs)
6

REAR GLASS
REAR GLASS
'I' JOINT
DETAIL : (F)
DETAIL : (G)
7
Pan head screw
(m4 x 12)
Cap screw
with flat washer
(m8 x 20zp)
STEP 1 STEP 2 STEP 3
STEP 4 STEP 5
REAR GLASS REAR GLASS RUBBER SEAL
(2018mm x 1pc) GLASS HOLDER BRACKET
(395mm x 5pcs)
REAR GLASS RUBBER SEAL
(1990mm x 2pcs) REAR GLASS HOLDER BRACKET
(395mm x 10pcs)
Do not tighten
DETAIL : (G)
DETAIL : (F)
Do not tighten

Check Leveling
Tighten all screw to ensure steady structure
90°
1632mm
8DETAIL : (H)
DETAIL : (J)
DETAIL : (K)
DETAIL : (H,I,J & K)
DETAIL : (H) DETAIL : (I) DETAIL : (J)
DETAIL : (K)
STEP 1
STEP 2
90°
90°
DETAIL : (I)

9
DETAIL : (L)
Cap screw with flat washer
(m8 x 20zp)
DETAIL : (L)
Cap screw with flat washer
(m8 x 20zp)
ALU FIXED GLASS

10
GLASS SWING DOOR

11
Pan Head Shelf Drilling Screw
(XR ZP #8 X 1/2")
DETAIL : (M)
Pan Head Shelf Drilling Screw
(XR ZP #8 X 1/2")
DETAIL : (M)

12
DETAIL : (N)
SCREW
COVER
SCREW
HANDLE
SHAFT
COVER
HANDLE
SCREW
GLASS PROTECTION NYLON
DOOR LATCH HANDLE
DETAIL : (N)

DETAIL : (O)
Before the first use,please open the battery
cover and remove the *protective film*
PAIR WITH RF RECEIVER
1- Click "learning key" on RF receiver
2- Click ON or OFF button on RF remote
3- LED lights connected with the receiver will
flicker once
4- The receiver is paired with remote successfully
HOW TO DELETE THE PAIRING
1- Press and hold down "learning key" on the
RF receiver for over 3 seconds until connected
LED lights flicker twice, which means the pairing
deleted successfully.
RF REMOTE
(REMOVE)
*PROTECTIVE FILM*
BATTERY COVER
BATTERY CR2430
13
VENTILATION FAN 2
LED LIGHT STRIP
RF RECEIVER
"LEARNING KEY"
6W SPLITTER
3W SPLITTER
VENTILATION FAN 1
INCOMING SUPPLY
SENSOR
LED LIGHT
VENTILATION FAN 1
CONTROL BOX
SOCKET OUTLET
VENTILATION FAN 2
DETAIL : (O)

Cap screw with flat washer
(m5 x 16zp)
SENSOR OUTLET
14
RIGHT PANEL
INTERNAL COVER
(Acoustic Board)
LEFT PANEL
INTERNAL COVER
(Acoustic Board)
BASE CARPET BOARD
TOP PANEL INTERNAL COVER
(Acoustic Board)
1
2
3
4

DETAIL : (P)
DETAIL : (P)
Cap screw with flat washer
(m8 x 20zp) JCBC SCREW
(m6 x 16 ZP)
TABLE POLE
TABLE POLE
COVER
TABLE SUPPORT
TABLE TOP
15

S/S A2 CSK HD MC SCREW
(m5 x 12)
16
ALU FIXED GLASS SEAL
(2000mm x 1pc)