INAPOD PHONE BOOTH Series User manual

ASSEMBLY DIAGRAM

INSTALLATION MANUAL
PHONE BOOTH SERIES
M POD
Please read installation manual carefully before assemble.
ATTENTION
First remove the accesory box. Carton number (20)
Follow the carton number when unboxing.
Complete assemble each according to the carton number and proceed to the next.

TOP PANEL
REAR
TOP SUPPORT
REAR GLASS
RIGHT PANEL
LEFT PANEL
BASE
CARPET BOARD
BASE FRAME
GLASS SWING DOOR
DOOR LATCH
HANDLE
REINFORCE 'L' BRACKET
TABLE SET
LEFT PANEL
INTERNAL COVER
(Acoustic Board) RIGHT PANEL
INTERNAL COVER
(Acoustic Board)

1
DETAIL : (A)
Adjustable foot cap for leveling
Push to final position
before setting up the booth
Level the base before installation
Step 1
Step 2
Step 3
Adjustable Foot Cap
x24 pcs
Leveling tool
DETAIL : (A)
BASE FRAME
Cap screw with flat washer
(m8 x 20zp)

2
DETAIL : (B)
Do not tighten
Cap screw with flat washer
(m8 x 20zp)
DETAIL : (B)
REINFORCE 'L' BRACKET

3
DETAIL : (C)
Do not tighten
Cap screw with flat washer
(m8 x 20zp)
DETAIL : (C)

4
DETAIL : (D)
DETAIL : (E)
SPECIAL TOOL
SPECIAL TOOL
DETAIL : (D) DETAIL : (E)
Cap screw with flat washer
(m5 x 16zp)
Rear
Top Support
Rear
Bottom Support

5
DETAIL: (MT3)
STEP 1 STEP 2 STEP 3
Rear Glass
Top Panel Rear
Top Support
Rear Glass
Top Panel Rear
Top Support
Rear Glass
Top Panel Rear
Top Support
VENTILATION FAN
TOP PANEL
DETAIL : (MT3)
Pan head screw
(m4 x 12)
Cap screw with flat washer
(m8 x 20zp)

6
REAR GLASS RUBBER SEAL
(1990mm x 2pcs)
REAR GLASS
(x2pcs)
REAR GLASS 'I' JOINT
(2025mm x 1pc)
REAR GLASS RUBBER SEAL
(1110mm x 2pcs)
GLASS HOLDER BRACKET
(395mm x 15pcs)

7
DETAIL : (G)
STEP 1 STEP 2 STEP 3
STEP 4 STEP 5
REAR GLASS REAR GLASS RUBBER SEAL
(2018mm x 1pc) GLASS HOLDER BRACKET
(395mm x 5pcs)
REAR GLASS RUBBER SEAL
(1990mm x 2pcs) REAR GLASS HOLDER BRACKET
(395mm x 10pcs)
Do not tighten
DETAIL : (F)
DETAIL : (G)
Do not tighten
REAR GLASS
REAR GLASS
'I' JOINT
DETAIL : (F)
Cap screw
with flat washer
(m8 x 20zp)
Pan head screw
(m4 x 12)

8
Check Leveling
Tighten all screw to ensure steady structure
DETAIL : (H,I,J & K)
DETAIL : (H) DETAIL : (I) DETAIL : (J)
DETAIL : (K)
STEP 1
STEP 2
DETAIL : (H)
DETAIL : (J)
DETAIL : (K)
DETAIL : (I)
90°
90°
90°
90°

9
DETAIL : (L)
Cap screw with flat washer
(m8 x 20zp)
DETAIL : (L)

10
GLASS SWING DOOR

11
DETAIL : (M)
Pan Head Shelf Drilling Screw
(XR ZP #8 X 1/2")
Pan Head Shelf Drilling Screw
(XR ZP #8 X 1/2")

12
DETAIL : (N)
SCREW
COVER
SCREW
HANDLE
SHAFT
COVER
HANDLE
SCREW
GLASS PROTECTION NYLON
DOOR LATCH
HANDLE
DETAIL : (N)

13
DETAIL : (O)
Before the first use,please open the battery
cover and remove the *protective film*
PAIR WITH RF RECEIVER
1- Click "learning key" on RF receiver
2- Click ON or OFF button on RF remote
3- LED lights connected with the receiver will
flicker once
4- The receiver is paired with remote successfully
HOW TO DELETE THE PAIRING
1- Press and hold down "learning key" on the
RF receiver for over 3 seconds until connected
LED lights flicker twice, which means the pairing
deleted successfully.
RF REMOTE
(REMOVE)
*PROTECTIVE FILM*
BATTERY COVER
BATTERY CR2430
LED LIGHT STRIP
RF RECEIVER
"LEARNING KEY"
6W SPLITTER
3W SPLITTER
VENTILATION FAN
INCOMING SUPPLY
SENSOR
LED LIGHT
VENTILATION FAN
SOCKET OUTLET
VENTILATION FAN
DETAIL : (O)
VENTILATION FAN
VENTILATION FAN
VENTILATION FAN
VENTILATION FAN
CONTROL BOX

RIGHT PANEL
INTERNAL COVER
(Acoustic Board)
14
BASE CARPET BOARD
LEFT PANEL INTERNAL COVER
(Acoustic Board)
TOP PANEL INTERNAL COVER
(Acoustic Board)
Cap screw with flat washer
(m5 x 16zp)

15
DETAIL : (P)
SOCKET OUTLET SOCKET OUTLET
TABLE POLE
x2pcs
TABLE POLE
COVER x2pcs TABLE SUPPORT
TABLE TOP
DETAIL : (P)
Cap screw with flat washer
(m8 x 20zp) JCBC SCREW
(m6 x 16 ZP)

16
ALU FIXED GLASS SEAL
(2000mm x 2pcs)
SIDE STEP
S/S A2 CSK HD MC SCREW
(m5 x 12)

17