INAPOD PHONE BOOTH Series User manual

ASSEMBLY DIAGRAM

INSTALLATION MANUAL
PHONE BOOTH SERIES
S POD
ATTENTION
Please read this instruction carefully and check all the parts before assembly.
Please be careful during the assembly to prevent hurting or damage of product.

1
BASE FRAME
DETAIL : (A)
Adjustable foot cap for leveling
Leveling tool
Push to final position
before setting up the booth
Level the base before installation
Step 1
Step 2
Step 3
DETAIL : (A)
Adjustable Foot Cap
x8 pcs

DETAIL : (B)
2
REINFORCE 'L' BRACKET
DETAIL : (B)
Do not tighten
Cap screw with flat washer
(m8 x 20zp)

DETAIL : (C)
DETAIL : (C)
3
LEFT PANEL
RIGHT PANEL
Do not tighten
Cap screw with flat washer
(m8 x 20zp)

4
DETAIL : (D)
DETAIL : (E)
DETAIL : (D)
DETAIL : (E)
Rear
Top Support
Rear
Bottom Support
Cap screw with flat washer
(m5 x 16zp)
REAR VIEW
SPECIAL TOOL
SPECIAL TOOL

5
GLASS HOLDER BRACKET
(1004mm x 4pcs)
REAR GLASS
REAR GLASS RUBBER SEAL
(1990mm x 2pcs)

6
STEP 1
Do not tighten
STEP 2
STEP 3
Pan head screw
(m4 x 12)
REAR GLASS
REAR GLASS RUBBER SEAL
(1990mm x 2pcs)
REAR GLASS HOLDER BRACKET
(1004mm x 4pcs)

7
STEP 1 STEP 2 STEP 3
Rear Glass
Top Panel Rear
Top Support
Rear Glass
Top Panel Rear
Top Support
Rear Glass
Top Panel Rear
Top Support
DETAILS
VENTILATION FAN
TOP PANEL
TOP PANEL
TOP PANEL
TOP PANEL
STEP 1
STEP 2
STEP 3
Pan head screw
(m4 x 12)

8
GLASS HOLDER BRACKET
(800mm x 1pc) STEP 1
STEP 2
STEP 3
REAR GLASS RUBBER SEAL
(825mm x 1pc)
Pan head screw
(m4 x 12)
Cap screw with flat washer
(m8 x 20zp)
REAR GLASS RUBBER SEAL
(825mm x 1pc)
REAR GLASS HOLDER BRACKET
(800mm x 1pc)
SCREW

9
90°
90°
90°
90°
DETAIL : (H)
DETAIL : (F)
DETAIL : (I)
DETAIL : (G)
Check Leveling
Tighten all screw to ensure steady structure
DETAIL : (F,G,H & I)
DETAIL : (F) DETAIL : (G)
DETAIL : (I)
STEP 1
STEP 2
DETAIL : (H)

10
DETAIL : (J)
INCOMING SUPPLY
SENSOR
SOCKET OUTLET
LED LIGHT
VENTILATION FAN
CONTROL BOX
DETAIL : (J)
VENTILATION FAN
LED LIGHT STRIP
RF RECEIVER
"LEARNING KEY"
Before the first use,please open the battery
cover and remove the *protective film*
PAIR WITH RF RECEIVER
1- Click "learning key" on RF receiver
2- Click ON or OFF button on RF remote
3- LED lights connected with the receiver will
flicker once
4- The receiver is paired with remote successfully
HOW TO DELETE THE PAIRING
1- Press and hold down "learning key" on the
RF receiver for over 3 seconds until connected
LED lights flicker twice, which means the pairing
deleted successfully.
6W SPLITTER
3W SPLITTER
RF REMOTE
(REMOVE)
*PROTECTIVE FILM*
BATTERY COVER
BATTERY CR2430

11
TABLE BRACKET
BASE CARPET BOARD
Cap screw with flat washer
(m8 x 20zp)

12
TOP PANEL INTERNAL COVER
(Acoustic Board)
LEFT PANEL INTERNAL COVER
(Acoustic Board)
RIGHT PANEL INTERNAL COVER
(Top Acoustic Board)
RIGHT PANEL INTERNAL COVER
(Bottom Acoustic Board)
1
2
3
4

13
TABLE TOP
SIDE STEP
S/S A2 CSK HD MC SCREW
(m5 x 12) JCBC SCREW
(m6 x 16 ZP)

14
GLASS SWING DOOR

15
DOOR LATCH HANDLE
DETAIL : (K)
DETAIL : (K)
SCREW
COVER
SCREW
HANDLE
SHAFT
COVER
HANDLE
SCREW
GLASS PROTECTION NYLON