Incept Tasman K40S User manual

K40S Tasman
Inflatable Sea Kayak
4.30 m, 1-person
Incept Marine Ltd
126 Hautapu Street, Taihape 4720, New Zealand.
ph ++64 6 388-0729
fx ++64 6 388-0747
email: [email protected]

Congratulations on your purchase of the Incept K40S Tasman Inflatable Sea Kayak!
An inflatable sea kayak which weighs just 17 kg and packs down to an ultra compact 75L -
inclusive of pump, decks, seat, pedals and rudder! And will carry an impressive load of 160
kg of crew and gear! And once familiar with the adjustments and fittings, you will take less
than 10 minutes to assemble!
There has been universal acclaim and reports of speed and handling comparable with well
known hard-shell kayaks. And because the decks are readily removable, it is a simple matter
to stow expedition gear.
Surprisingly strong and stable, the K40S Tasman will handle big seas and survive impacts
which would break rigid hulls. Made of durable reinforced polyurethane alloy, given basic
care the boat material will take the knocks and give exceptional service.
Truly a jet-setting kayak, the Incept K40S Tasman will repay your choice with reliable and
happy boating for many years.
FEATURES
Robust construction and innovative design give these kayaks a stiff frame, excellent speed,
high stability and good handling. Main features are -
• FOLDABILITY - a 16 kg, fully featured sea kayak which folds down into a piece
of airline baggage!
• RUDDER - detachable high-tech rudder and foot controls
• STOWAGE - zipped decks and room for stowing trip gear in stern and bow
allows plenty of options for optimum trim on expeditions
• ACCESS’BL DECKS - originally inspired by Audrey Sutherland and used by her for
thousands of sea miles, velcro’d decks have been upgraded with
water-resistant zips and full length access
• SPRAY SKIRT - standard off-the-shelf neoprene spray skirt on secure coaming
• SPEED / HANDLING - comparable with hard-shells
• COMFORT - adjustable seat and footrest give great support and comfort
• GRABLINE - full length fitted safety grab-line
• LINE SUPPORTS - plenty of external attachment points for tethers etc
•
PUMP - top quality strong, high-pressure US barrel pump

SPECIFICATIONS:
LENGTH 4.35 m 14' 3" CREW 1 person
WIDTH 67 cm 26" LOAD 160 kg 350 lb
TUBE 13 x 25cm 5 x 10" BARE WEIGHT 17 kg 37 lb
INTERNAL 40 cm 16" (includes all fittings and pump)
The Incept K40S inflatable sea kayak is constructed from a heavy duty and light weight
Polyurethane alloy boat material designed for Incept’s back-packable wilderness boats. It has
1100 dtex Polyester reinforcing, is exceptionally strong and hard wearing, and is protected
to withstand New Zealand’s extreme UV exposure.
ASSEMBLY
• INFLATE The main inflation valves are in the cockpit and operated by pressing
down the internal stem and twisting a quarter turn. When the stem holds
down the valve is open. Release the stem to close the valve for inflation.
The protective caps prevent the entry of gravel and dirt.
Close the inflation valves and inflate the three air chambers (sponsons
and floor). If you find the pump nozzle is a loose fit, use the blue adapter
in the pump bag.
Pump hard enough to blow the three relief valves. Fit the valve caps.
• RUDDER Set the rudder-raise control to the home
position (rudder down) in the jamcleat at left
(port) of the rear cockpit.
Fit the rudder and attach the three control
lines.
Be sure the rudder pin is pushed fully into
place, required for transmitting the steering
action.
If the plastic connecting nuts are given a half-
dozen counter twists beforehand, line
twisting will be minimised.
• SEATS Clip the seat into the cockpit (4 snaps). Inflate by mouth and twist the
valves closed.
Inflate the back-rest as hard as possible. Inflate the seat cushion very soft,
almost flaccid, for comfort, support and for getting the paddler weight
low.

The seat cushion valve is positioned between the legs so it can be opened at sea for
adjustment if you need it.
A small amount of adjustment is possible. The top of backrest should
be partially under the rear deck.
• FOOTREST The footrest / pedals assembly
is inflated by mouth to a
moderate pressure, not critical.
With the rudder in a neutral
(straight-ahead) position, the
rudder lines can be adjusted at
the forward tie-point so that
the pedals lean slightly towards
the paddler. This has been pre-
set at the factory but may need further adjustment after a settling period
or first use..
The footrest is adjustable on the webbing straps for leg length. The rudder
lines will automatically adjust without further attention.
The pedal elastic cords should be adjusted so tension is sufficient only to
hold the pedals up. To avoid drag in the rudder lines do not over-tension.
• DECKS The decks are an important and integral part of the
boat structure, stiffening the hull significantly
when closed.
Fit the curved fibreglass battens in the 4 pockets
provided in the deck undersides. Important: pull
the decks in to relieve the zips of any load when
closing them. An occasional spray with silicone
will keep the zips closing easily.
Important: When opening the decks it is
necessary to half withdraw the battens.

• COCKPITS Insert the white rod into the cockpit coaming sleeve and pull in tight
with the tab closure. Pull the webbing strap tight for security. Leave the
black cord in the rod end hanging out for easy removal later.
• PUMP The barrel pump supplied is a heavy duty American pump which can
easily reach the higher boat pressures needed for this performance
kayak. Because it does not require a hose it can be used at sea to fix the
pressure drop at launching which occurs when the sea is cold and the
beach is hot. The inflation valves are located in the cockpit for this
reason.
• SPRAYSKIRTS Pull the sprayskirt up over your legs to chest height with the long part
of the skirt in front. Adjust the shoulder braces. You may choose not to
wear the braces - in which case tuck them inside the body tube.
Wear your paddle jacket and PFD (personal flotation device / life
jacket) over the spray skirt.
When you get into the kayak, reach behind with the back of the skirt
elastic and tuck it under the edge of the cockpit coaming. Stretch the
elastic edge of the skirt forward with both hands, one each side, tucking
under the coaming as you work towards the front. When you reach the
front of the skirt be sure the pull tab is out on TOP of the deck.
WARNING: This is a matter for your safety if you should need to
exit in emergency.
BOAT HANDLING
Performance is improved with pressure. Each of the main inflation chambers is fitted with
a pressure relief valve set to the optimum inflation pressures. If the boat is left on the
beach in the sun and internal pressures rise, the relief valves will blow. When the boat
subsequently cools (taken out of the sun or put in the water), there will be a corresponding
loss of pressure and you may wish to top up with the pump. You should only want to do
this if you notice undue flex in the boat at sea.
How to paddle a kayak is outside the scope of this manual. Good books on the subject of sea
kayaking are readily available.
It is essential that any user of this kayak take all reasonable steps to learn the basics of safety
at sea before venturing out. To gain experience, join a local sea kayak network or club.
The leaflet "A Basic Guide to Safe Sea Kayaking" is included with this manual. If this should
be missing, or additional copies are needed, please contact the agent who sold you this kayak
or Incept Marine Ltd or the Kiwi Association of Sea Kayakers, PO Box 23, Runanga 7854,
West Coast, New Zealand.

CARE
CLEANING & MAINTENANCE:
Use warm soapy water or light abrasive cleanser to remove dirt and stains.
Periodically clean and if necessary lubricate the zippers with a silicone spray.
Remove sand and gravel which may accumulate between the floor and the sidewalls.
Lubricate control lines with silicone where they pass through the guides.
Wipe the boat with 303 Protectant to restore lustre and keep your kayak looking new.
FOLDING / STOWING:
To stow the boat, remove the rudder, cockpit coaming rods, curved deck battens and seats.
Before storing, inflate the kayak, fit the valve caps and wash with fresh water.
Dry thoroughly: - with sponsons inflated and floor slack, lift off the ground supported at
bow and stern until dry, particularly in the sandflap (between floor and sponsons). Storing
wet will result in mildew and possibly permanent stains.
Open the inflation valves with a simple press down / quarter turn.
Fold the boat as in the diagram above.

Spend a moment in getting the boat flat with the sides turned in a little (1).
Fold the kayak from the bow to expel all air (2 & 3) then re-roll from the stern to protect the
valves (4 - 7) and get the bundle smaller. Kneel on the bundle as you go. Secure the package
with the compression strap supplied (8).
A little time spent in learning how to roll your boat properly will be most worthwhile.
Most damage to inflatable boats occurs off the water when in the folded state. Folded corners
which are dragged on hard ground can be expected to hole. In particular be careful with the
folded package where the internal parts of the valves protrude against the boat material. Do not
lay such a bump down on, say, the deck of a moving truck.
REPAIRS:
A basic repair kit of boat material and adhesive is included with the boat.
The adhesive requires warm and dry working conditions for best results. Preparation of a
permanent repair is as follows:-
• Cut a patch to fit the repair leaving 25mm (1") edge distance to the hole. Round corners
for appearance and resistance to lifting.
• Dry the surfaces and preferably clean with an M.E.K.(methyl ethyl ketone) solvent
damped cloth.
• Position the patch and mark the outline on to the boat with a pencil.
• Brush glue on to both surfaces. Do not over brush as the glue will drag and become
lumpy. Allow to dry 15 - 30 minutes, more in cool conditions.
• Place the patch and heat - warm to the touch - if necessary using a hair dryer or hot-air
gun. Heat activates the glue, providing an instant and permanent bond. Apply pressure
to the patch while warm. A portable camp cooker is a useful warming tool for on-trip
repairs (under a sheet in adverse conditions) - but do not overheat.
Temporary repairs can be made without heat or solvent if the patch is applied before one of
the glued surfaces is dry, i.e. while still slightly tacky.
WARRANTY
INCEPT’s K series inflatable kayaks in non-commercial use are guaranteed for a period of
five years from the date of purchase. Any manufacturing defects in materials or workmanship
found during the warranty period will be made good by Incept Marine Ltd at no cost,
provided only that the boat is returned to the nearest Incept repair station, freight paid. Call
the dealer from whom you purchased the boat, or Incept, for details.

[Mk 6 K50D Pacific Double, Stewart Island New Zealand]
INCEPT K40S Tasman
- proudly made in New Zealand by Incept -
BOAT SERIAL No. INC39
PURCHASE DATE / /
Copyright Incept Marine Ltd 2008