Indesit KN1G2/UA User manual
Contents
Installation, 2-5
Positioning and levelling
Electrical connections
Gas connection
Adapting to different types of gas
Technical data
Table of burner and nozzle specifications
Description of the appliance, 6
Overall view
Control panel
Start-up and use, 7-8
Using the hob
Using the oven
Oven cooking advice table
Precautions and tips, 9
General safety
Disposal
Respecting and conserving the environment
Maintenance and care, 10
Switching the appliance off
Cleaning the appliance
Gas tap maintenance
Replacing the oven light bulb
Assistance
Operating Instructions
COOKER
GB
English, 1 Укаінька,23
Română,34
У,11
RS UA
RO
GB
KN1G2/UA
KNJ1G2/UA
KN1G20/UA
2
GB !Before operating your new appliance please read
this instruction booklet carefully. It contains
important information concerning the safe installation
and operation of the appliance.
!Please keep these operating instructions for future
reference. Make sure that the instructions are kept
with the appliance if it is sold, given away or moved.
!The appliance must be installed by a qualified
professional according to the instructions provided.
!Any necessary adjustment or maintenance must be
performed after the cooker has been disconnected
from the electricity supply.
Room ventilation
The appliance may only be installed in permanently-
ventilated rooms, according to current national
legislation. The room in which the appliance is
installed must be ventilated adequately so as to
provide as much air as is needed by the normal gas
combustion process (the flow of air must not be
lower than 2 m3/h per kW of installed power).
The air inlets, protected by grilles, should have a
duct with an inner cross section of at least 100 cm2
and should be positioned so that they are not liable
to even partial obstruction (
see figure A
).
These inlets should be enlarged by 100% - with a
minimum of 200 cm2- whenever the surface of the
hob is not equipped with a flame failure safety
device. When the flow of air is provided in an
indirect manner from adjacent rooms (
see figure B
),
provided that these are not communal parts of a
building, areas with increased fire hazards or
bedrooms, the inlets should be fitted with a
ventilation duct leading outside as described above.
AB
!After prolonged use of the appliance, it is
advisable to open a window or increase the speed of
any fans used.
Disposing of combustion fumes
The disposal of combustion fumes should be
guaranteed using a hood connected to a safe and
efficient natural suction chimney, or using an electric
fan that begins to operate automatically every time
the appliance is switched on (
see figure
).
!The liquefied petroleum gases are heavier than air
and collect by the floor, therefore all rooms
containing LPG cylinders must have openings
leading outside so that any leaked gas can escape
easily.
LPG cylinders, therefore, whether partially or
completely full, must not be installed or stored in
rooms or storage areas that are below ground level
(cellars, etc.). Only the
cylinder being used should be stored in the room;
this should also be kept well away from sources
of heat (ovens, chimneys, stoves) that may cause
the temperature of the cylinder to rise above 50°C.
Positioning and levelling
!It is possible to install the appliance alongside
cupboards whose height does not exceed that of the
hob surface.
!Make sure that the wall in contact with the back of
the appliance is made from a non-flammable, heat-
resistant material (T 90°C).
To install the appliance correctly:
• Place it in the kitchen, dining room or the bed-sit
(not in the bathroom).
• If the top of the hob is higher than the cupboards,
the appliance must be installed at least 200 mm
away from them.
• If the cooker is installed underneath a wall cabinet,
there must be a minimum distance of 420 mm
between this cabinet and the top of the hob.
This distance should be increased to 700 mm if
the wall cabinets are flammable (
see figure
).
A
Fumes channelled through
a chimney or branched
flue system reserved for
cooking appliances)
Installation
Adjacent room Room requiring
ventilation
Ventilation opening for
comburent air
Increase in the gap between
the door and the flooring
Fumes channelled
straight outside
3
GB
• Do not position
blinds behind the
cooker or less than 200
mm away from its
sides.
• Any hoods must be
installed according to
the instructions listed in
the relevant operating
manual.
Levelling
If it is necessary to level the
appliance, screw the
adjustable feet into the places
provided on each corner of the
base of the cooker (
see
figure
).
The legs* fit into the slots on
the underside of the base of
the cooker.
Electrical connection
Install a standardised plug corresponding to the
load indicated on the appliance data plate (
see
Technical data table
).
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum
contact opening of 3 mm installed between the
appliance and the mains. The circuit-breaker must be
suitable for the charge indicated and must comply with
NFC 15-100 regulations (the earthing wire must not be
interrupted by the circuit-breaker). The supply cable
must be positioned so that it does not come into
contact with temperatures higher than 50°C at any point.
Before connecting the appliance to the power
supply, make sure that:
• The appliance is earthed and the plug is compliant
with the law.
• The socket can withstand the maximum power of
the appliance, which is indicated by the data plate.
• The voltage is in the range between the values
indicated on the data plate.
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min. mm.
420
Min. mm.
* Only available in certain models
!Once the appliance has been installed, the power
supply cable and the electrical socket must be
easily accessible.
!The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only.
!The manufacturer declines any liability should
these safety measures not be observed.
Gas connection
Connection to the gas network or to the gas cylinder
may be carried out using a flexible rubber or steel
hose, in accordance with current national legislation
and after making sure that the appliance is suited to
the type of gas with which it will be supplied (see the
rating sticker on the cover: if this is not the case
see
below
). When using liquid gas from a cylinder, install a
pressure regulator which complies with current national
regulations. To make connection easier, the gas
supply may be turned sideways*: reverse the position
of the hose holder with that of the cap and replace the
gasket that is supplied with the appliance.
!Check that the pressure of the gas supply is
consistent with the values indicated in the Table of
burner and nozzle specifications (
see below
). This
will ensure the safe operation and durability of your
appliance while maintaining efficient energy
consumption.
Gas connection using a flexible rubber hose
Make sure that the hose complies with current
national legislation. The internal diameter of the hose
must measure: 8 mm for liquid gas supply; 13 mm
for methane gas supply.
Once the connection has been performed, make
sure that the hose:
• Does not come into contact with any parts that
reach temperatures of over 50°C.
• Is not subject to any pulling or twisting forces and
that it is not kinked or bent.
• Does not come into contact with blades, sharp
corners or moving parts and that it is not
compressed.
• Is easy to inspect along its whole length so that
its condition may be checked.
• Is shorter than 1500 mm.
• Fits firmly into place at both ends, where it will be
fixed using clamps that comply with current
regulations.
4
GB
A
V
!If one or more of these conditions is not fulfilled or
if the cooker must be installed according to the
conditions listed for class 2 - subclass 1 appliances
(installed between two cupboards), the flexible steel
hose must be used instead (
see below
).
Connecting a flexible jointless stainless steel pipe
to a threaded attachment
Make sure that the hose and gaskets comply with
current national legislation.
To begin using the hose, remove the hose holder on the
appliance (the gas supply inlet on the appliance is a
cylindrical threaded 1/2 gas male attachment).
!Perform the connection in such a way that the hose
length does not exceed a maximum of 2 metres,
making sure that the hose is not compressed and
does not come into contact with moving parts.
Checking the connection for leaks
When the installation process is complete, check
the hose fittings for leaks using a soapy solution.
Never use a flame.
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas
other than the default type (this is indicated on the
rating label on the cover).
Adapting the hob
Replacing the nozzles for the hob burners:
1. Remove the hob grids and slide the burners off
their seats.
2. Unscrew the nozzles using a
7 mm socket spanner (
see
figure
), and replace them with
nozzles suited to the new type
of gas(
see Burner and nozzle
specifications table
).
3. Replace all the components
by following the above
instructions in reverse.
Adjusting the hob burners’ minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory
screw, which is positioned inside or next to the tap
pin, until the flame is small but steady.
!If the appliance is connected to a liquid gas
supply, the regulatory screw must be fastened as
tightly as possible.
3. While the burner is alight, quickly change the position
of the knob from minimum to maximum and vice versa
several times, checking that the flame is not
extinguished.
!The hob burners do not require primary air adjustment.
Adapting the oven
Replacing the oven burner nozzle:
1. Remove the oven compartment.
2. Slide out the protection
panel A
(
see diagram
).
3. Remove the oven burner
after unscrewing the screws V
(
see figure
).
The whole operation will be
made easier if the oven door
is removed.
4. Unscrew the nozzle using a
special nozzle socket spanner
(
see figure
) or with a 7 mm
socket spanner, and replace it
with a new nozzle that is
suited to the new type of gas
(
see Burner and nozzle
specifications table
).
Adjusting the gas oven burner’s minimum setting:
1. Light the burner (
see Start-up and Use
).
2. Turn the knob to the minimum position (MIN) after
it has been in the maximum position (MAX) for
approximately 10 minutes.
3. Remove the knob.
4. Tighten or loosen the adjustment screws on the
outside of the thermostat pin (
see figure
) until the
flame is small but steady.
!If the appliance is connected to liquid gas, the
adjustment screw must be fastened as tightly as
possible.
5
GB
5. Turn the knob from the MAX position to the MIN
position quickly or open and shut the oven door,
making sure that the burner is not extinguished.
We recommend cleaning the oven before using it for
the first time, following the instructions provided in
the "Care and maintenance" section.
SS
R
A
TECHNICAL DATA
Oven dimensions
(HxWxD)
34x39x38 cm
Volume 50 l
Useful
measurements
relating to the oven
compartment
width 42 cm
depth 44 cm
height 17 cm
Power supply voltage
and frequency
see data plate
Burners
may be adapted for use with any
type of gas shown on the data
plate, which is located inside the
flap or, after the oven
compartment has been opened,
on the left-hand wall inside the
oven.
EC Directives: 2006/95/EC dated
12/12/06 (Low Voltage) and
subsequent amendments -
2004/108/EC dated 15/12/04
(Electromagnetic Compatibility)
and subsequent amendments -
2009/142/EC dated 30/11/09
(Gas) and subsequent
amendments - 93/68/EEC dated
22/07/93 and subsequent
amendments - 2002/96/EC.
1275/2008 (Stand-by/ Off mode)
Table of burner and nozzle specifications
* At 15°C and 1013 mbar- dry gas
** Propane P.C.S. = 50,37 MJ/Kg
*** Butane P.C.S. = 49,47 MJ/Kg
Natural P.C.S. = 37,78 MJ/m3
KN1G2/UA
KNJ1G2/UA
KN1G20/UA
Table 1 Liquid Gas Natural Gas
!""
#
$
!""
#
!""
#
! %&&
#
'$% ( ) + 26 :2 :+ 6 :26 +( :26
;#
<&; )> ? + ( ) (2 (6 6 2 2 2
@D
;@ >> + ( > )( ) )? ?> 2 ?>
EF : +2+? 62 +> +( ) ? + ?
;
!G
<G
<DG
:2(
:
(>
()
:>
+>
:
)
:>
(
6H>
2
6
GB
Description of the
appliance
*Only available in certain models.
Control panel
Overall view
OVEN
control knob
Hob BURNER
control knobs
Electronic Lighting
for Hob Burners*
Button for Oven Light*
7
GB
Using the hob
Lighting the burners
For each BURNER knob there is a complete ring
showing the strength of the flame for the relevant
burner.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an
anticlockwise direction so that it is pointing to the
maximum flame setting E.
3. Adjust the intensity of the flame to the desired
level by turning the BURNER knob in an
anticlockwise direction. This may be the minimum
setting C, the maximum setting Eor any position in
between the two.
If the appliance is fitted with
an electronic lighting
device* (
see figure
), press
the ignition button, marked
with the symbol , then
hold the BURNER knob
down and turn it in an
anticlockwise direction, towards the maximum flame
setting, until the burner is lit.
Several models are equipped with an ignition device
which is built into the knob; in this case the
electronic ignition device* is present (
C
) but the
ignition button is not. Simply press the BURNER
knob and turn it in an anticlockwise direction so that
it is pointing to the maximum flame setting, until the
burner is lit. The burner may be extinguished when
the knob is released. If this occurs, repeat the
operation, holding the knob down for a longer period
of time.
!If the flame is accidentally extinguished, switch off
the burner and wait for at least 1 minute before
attempting to relight it.
If the appliance is equipped with a flame failure
safety device*(X), press and hold the BURNER knob
for approximately 2-3 seconds to keep the flame
alight and to activate the device.
To switch the burner off, turn the knob until it
reaches the stop position •.
Practical advice on using the burners
For the burners to work in the most efficient way
possible and to save on the amount of gas
consumed, it is recommended that only pans that
have a lid and a flat base are used. They should
also be suited to the size of the burner.
Start-up and use
To identify the type of burner, please refer to the
diagrams contained in the “Burner and nozzle
specifications”.
Using the oven
!The first time you use your appliance, heat the
empty oven with its door closed at its maximum
temperature for at least half an hour. Ensure that the
room is well ventilated before switching the oven off
and opening the oven door. The appliance may emit
a slightly unpleasant odour caused by protective
substances used during the manufacturing process
burning away.
!Before operating the product, remove all plastic
film from the sides of the appliance.
!Never put objects directly on the bottom of the
oven; this will avoid the enamel coating being
damaged. Only use position 1 in the oven when
cooking with the rotisserie spit.
Lighting the oven
To light the oven burner, apply
a lighted match or a lighter to
hole and while pressing in all
the way set the oven knob on
maximummaximum
maximummaximum
maximum EE
EE
E.
The burner can be used at
maximum or intermediate
settings. These settings, maximummaximum
maximummaximum
maximum EE
EE
E. and
minimumminimum
minimumminimum
minimum CC
CC
Care indicated on the knob, plus off,
identified by the symbol • and operative when this
symbol points to the notch.
For the minimum to maximum settings turn the knob
counter clockwise from “Off”.
To turn off the burner, turn the knob clockwise until it
stops (corresponding again with setting •).
!The oven is fitted with a safety device and it is
therefore necessary to hold the OVEN control knob
down for approximately 6 seconds*.
F
*Only available in certain models.
Burner ø Cookware diameter (cm)
Fast(R) 24-26
SemiFast(S) 16-20
Auxiliary(A) 10-14
X
C
8
GB
*Only available in certain models.
A
S
!If the flame is accidentally extinguished, switch off
the burner and wait for at least 1 minute before
attempting to relight the oven.
Oven light*
The light may be switched on at any moment by
pressing the OVEN LIGHT button.
Timer*
To activate the Timer proceed as follows:
1. Turn the TIMER knob in a clockwise direction 4
for almost one complete revolution to set the buzzer.
2. Turn the TIMER knob in an anticlockwise direction
5to set the desired length of time.
Lower compartment*
There is a compartment
underneath the oven that may
be used to store oven
accessories or deep dishes. To
open the door pull it
downwards (
see figure
).
!The internal surfaces of the compartment (where
present) may become hot.
!Do not place flammable materials in the lower oven
compartment.
In gas cooker models, there is
a sliding protection layer A
that shields the lower
compartment from the heat
generated by the burner (
see
figure
).
To remove the sliding
protection remove the screw S
(
see figure
). To replace it, lock
it in place with the screw S.
!Before using the oven make
sure that the sliding protection
is fixed correctly.
Oven cooking advice table
Food to be cooked Wt.
(Ig)
Cookin position of
shelves from
bottom
Temperature
(LO)
Pre-heatin time
(min)
Cookin time
(min.)
Pasta
Lasagne
Oannelloni
Pastabakesaugratin
2.5
2.5
2.5
3
3
3
210
200
200
10
10
10
60-75
40-50
40-50
Meat
Qeal
Ohicken
Duck
abbit
Pork
Lamb
1.7
1.5
1.8
2.0
2.1
1.8
3
3
3
3
3
3
200
220
200
200
200
200
10
10
10
10
10
10
85-90
90-100
100-110
70-80
70-80
90-95
Fish
Mackerel
Dentex
Tr o u t bakedinpaper
1.1
1.5
1.0
3
3
3
180-200
180-200
180-200
10
10
10
35-40
40-50
40-45
Pizza
Neapolitan 1.0 3 220 15 15-20
Cake
Biscuits
Ta r t s
Savourypie
aisedOakes
0.5
1.1
1.0
1.0
3
3
3
3
180
180
180
165
15
15
15
15
30-35
30-35
45-50
35-40
NB:cookingtimesareapproximateandmayvaryaccordingtopersonaltaste.
9
GB
Precautions and tips
!This appliance has been designed and manufactured in
compliance with international safety standards.
The following warnings are provided for safety reasons and
must be read carefully.
General safety
•These instructions are only valid for the
countries whose symbols appear in the
manual and on the serial number plate.•
The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial use.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• Do not touch the appliance with bare feet or with wet or
damp hands and feet.
•The appliance must be used by adults only for
the preparation of food, in accordance with the
instructions outlined in this booklet. Any other
use of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous.
The manufacturer may not be held liable for
any damage resulting from improper, incorrect
and unreasonable use of the appliance.
• The instruction booklet accompanies a class 1 (insulated)
or class 2 - subclass 1 (recessed between 2 cupboards)
appliance.
• Keep children away from the oven.
• Make sure that the power supply cables of other electrical
appliances do not come into contact with the hot parts of
the oven.
• The openings used for the ventilation and dispersion of
heat must never be covered.
• Do not close the glass hob cover (selected models only)
when the burners are alight or when they are still hot.
• Always use oven gloves when placing cookware in the
oven or when removing it.
• Do not use flammable liquids (alcohol, petrol, etc...) near
the appliance while it is in use.
• Do not place flammable material in the lower storage
compartment or in the oven itself. If the appliance is
switched on accidentally, it could catch fire.
• Always make sure the knobs are in the • position and that
the gas tap is closed when the appliance is not in use.
• When unplugging the appliance, always pull the plug from
the mains socket; do not pull on the cable.
• Never perform any cleaning or maintenance work without
having disconnected the appliance from the electricity
mains.
• If the appliance breaks down, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may cause
injury or further malfunctioning of the appliance. Contact
Assistance.
• Do not rest heavy objects on the open oven door.
• The appliance should not be operated by people
(including children) with reduced physical,
sensory or mental capacities, by inexperienced
individuals or by anyone who is not familiar with
the product. These individuals should, at the very
least, be supervised by someone who assumes
responsibility for their safety or receive
preliminary instructions relating to the operation of
the appliance.
• Do not let children play with the appliance.
Disposal
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using the
normal solid urban waste cycle. Exhausted appliances
should be collected separately in order to optimise the cost
of re-using and recycling the materials inside the machine,
while preventing potential damage to the atmosphere and
to public health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations regarding
separated waste collection.
Exhausted appliances may be collected by the public
waste collection service, taken to suitable collection areas
in the area or, if permitted by current national legislation,
they may be returned to the dealers as part of an
exchange deal for a new equivalent product.
All major manufacturers of household appliances
participate in the creation and organisation of systems for
the collection and disposal of old and disused appliances.
Respecting and conserving the
environment
• You can help to reduce the peak load of the electricity
supply network companies by using the oven in the hours
between late afternoon and the early hours of the morning.
• Check the door seals regularly and wipe them clean to
ensure they are free of debris so that they adhere properly
to the door, thus avoiding
heat dispersion.
10
GB
Care and maintenance
Switching the appliance off
Disconnect your appliance from the electricity supply
before carrying out any work on it.
Cleaning the appliance
!Do not use abrasive or corrosive detergents such as
stain removers, anti-rust products, powder detergents or
sponges with abrasive surfaces: these may scratch the
surface beyond repair.
!Never use steam cleaners or pressure cleaners on the
appliance.
• It is usually sufficient simply to wash the hob using a
damp sponge and dry it with absorbent kitchen roll.
• The stainless steel or enamel-coated external parts and
the rubber seals may be cleaned using a sponge that
has been soaked in lukewarm water and neutral soap.
Use specialised products for the removal of stubborn
stains. After cleaning, rinse well and dry thoroughly. Do
not use abrasive powders or corrosive substances.
• The hob grids, burner caps, flame spreader rings
and the hob burners can be removed
to make cleaning easier; wash them in hot water and
non-abrasive detergent, making sure all burnt-on
residue is removed before drying them thoroughly.
• For hobs with electronic ignition, the terminal part of the
electronic lighting devices should be cleaned
frequently and the gas outlet holes should be checked
for blockages.
• The inside of the oven should ideally be cleaned after
each use, while it is still lukewarm. Use hot water and
detergent, then rinse well and dry with a soft cloth. Do
not use abrasive products.
•Clean the glass part of the oven door using a sponge
and a non-abrasive cleaning product, then dry
thoroughly with a soft cloth. Do not use rough abrasive
material or sharp metal scrapers as these could
scratch the surface and cause the glass to crack.
• The accessories can be washed like everyday
crockery, and are even dishwasher safe.
• Stainless steel can be marked by hard water that has
been left on the surface for a long time, or by
aggressive detergents containing phosphorus. After
cleaning, rinse well and dry thoroughly. Any remaining
drops of water should also be dried.
The cover
If the cooker is fitted with a
glass cover, this cover
should be cleaned using
lukewarm water. Do not use
abrasive products.
It is possible to remove the
cover in order to make
cleaning the area behind
the hob easier. Open the
cover fully and pull it
upwards (
see figure
).
!Do not close the cover when the burners are alight or
when they are still hot.
Inspecting the oven seals
Check the door seals around the oven periodically. If the
seals are damaged, please contact your nearest
Authorised After-sales Service Centre. We recommend
that the oven is not used until the seals have been
replaced.
Gas tap maintenance
Over time, the taps may become jammed or difficult to
turn. If this occurs, the tap must be replaced.
!This procedure must be performed by a qualifiedThis procedure must be performed by a qualified
This procedure must be performed by a qualifiedThis procedure must be performed by a qualified
This procedure must be performed by a qualified
technician who has been authorised by thetechnician who has been authorised by the
technician who has been authorised by thetechnician who has been authorised by the
technician who has been authorised by the
manufacturer.manufacturer.
manufacturer.manufacturer.
manufacturer.
Replacing the oven light bulb
1. After disconnecting the oven
from the electricity mains, remove
the glass lid covering the lamp
socket (
see figure
).
2. Remove the light bulb and
replace it with a similar one:
voltage 230 V, wattage 25 W, cap
E 14.
3. Replace the lid and reconnect the oven to the electricity
supply.
Assistance
Please have the following information handy:
• The appliance model (Mod.).
• The serial number (S/N).
This information can be found on the data plate located on
the appliance and/or on the packaging.
, 12-15
Э
,16
,17-19
Э
Э
,20
Э
,21-22
А А
RS
GB RS
KN1G2/UA
KNJ1G2/UA
KN1G20/UA
English, 1 і,23
Română,34
,11
UA
RO
12
RS !
. ,
,
.
! :
,
.
!
.
!
.
.
, ,
,
( 2 3/
1 ).
,
,
100 2
,
, (. и А).
Э 100% -
200 2-
(.
и В) – ,
,
- ,
, .
!
.
,
,
,
(. и).
! ,
,
.
,
,
,
(, ..).
,
(, , ),
50°C.
!
,
.
!, ,
,
(90°C).
:
• ,
(
);
•
,
200 .
•
,
420
.
Э 700 ,
(. );
•
200 .
A
(
)
AB
13
RS
•
,
.
(.
и).
*
.
Э
,
,
(. и иии
и).
3 ,
NFC
15-100 (
).
,
50°C.
:
•
;
•
, ;
•
;
•
.
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min. mm.
420
Min. mm.
*
;
.
!
,
.
!Э
.
!
.
!
.
,
(.
: . и).
,
.
*:
.
! ,
,
, «
» (. и).
,
.
: 8
; 13 .
, :
• ,
50°C;
• , , ;
• , ,
;
• ;
• 1500 ;
•
,
.
14
RS
A
V
!
,
2,
1 (,
),
(. и).
.
,
.
(
Ѕ «»).
!
2
. ,
, .
, .
,
(
).
:
1.
;
2.
7
(. и)
,
(. и
Хиии и
);
3.
,
.
:
1.
;
2. ,
,
.
!
.
3. ,
.
!
- .
:
1. ;
2.
(. и);
3.
, V-
(. и);
,
.
4.
(. и)
7
,
(. и
Хиии и
).
:
1. (. П иЭия);
2. 10
(),
();
3. ;
4. ,
(. и),
и и.
!
;
15
RS
5. ,
-
.
, ,
«
».
SS
R
A
* 15°C 1013 – *** P.C.S. = 49,47 /
** P.C.S. = 50,37 / P.C.S. = 37,78 /
:
:
:
: KN1G2/UA; KNJ1G2/UA; KN1G20/UA
: Indesit Company
-:
/ : 34x39x38 / 50
220-240 V ~
-
50/60Hz -
I
Э
Ы
,
cert.rus@indesit.com.
: : 2006/95/EC
12/12/06 ( )
– 2004/108/C
15/12/04 (Э )
– 2009/142/C
30/11/09 () - 90/68/ 22/07/93
– 2002/96/.
1275/2008 (Stand-by/ Off mode)
,
-
(S/N XXXXXXXXX *
XXXXXXXXXXX),
:
- 1- S/N
,
- 2- 3- S/N -
,
- 4- 5- S/N -
.
:
Indesit Company S.p.A.
. 47, 60044, (),
: " "
01.01.2011: , 129223, ,
, , . 46
()
: 01.01.2011: , 127018, , .
, 12, . 1
KN1G2/UA
KNJ1G2/UA
KN1G20/UA
KN1G2/UA; KNJ1G2/UA; KN1G20/UA
,
,
(p.c.s.*)
1/100
1/100
*
/
1/100
*
/
1/100
*
/
. *** **
() (R) 100 3,00 0,7 41 86 218 214 116 286 143 286
() (S) 75 1,90 0,4 30 70 138 136 106 181 118 181
() (A) 55 1,00 0,4 30 50 73 71 79 95 80 95
-
()
()
()
28-30
20
35
37
25
45
20
17
25
13
6,5
18
2,00 1,00 48/49 68 145 143 107 190 190
114
16
RS
*
*
17
RS
Э
.
:
1.
;
2.
E.
3. ,
: C, E
.
* (C),
,
,
.
, .
* (. и),
.
. ,
,
.
,
.
!
1
.
* (X) ,
2-3
,
.
•.
, ,
, :
« ».
Э
!
30
. ,
. ,
, ,
.
!
, .
!
,
. 1
.
«F»
(. и.)
-
EE
EE
E..
,
-
. -
: EE
EE
E—
;CC
CC
C— , «•» —
. -
, •
()
.
( •).
В: -
,
«•» —
1 .
F
*
X
C
,
(R) 24–26
(S) 16–20
() 10–14
18
RS
*
S
!
,
6 *.
!
1
.
*
():
1. 4
;
2. 5
, .
*
,
.
(.
и).
!
.
! (
) .
A
,
(.
и).
S
(.
и).
S.
!
,
.
19
RS
*
,
,
.
-
,
°C
,
2,5 3 10 210 60-75
2,5 3 10 200 40-50
2,5 3 10 200 40-50
1,7 3 10 200 85-90
1,5 3 10 220 90-100
1,8 3 10 200 100-110
2,0 3 10 200 70-80
2,1 3 10 200 70-80
1,8 3 10 200 90-95
1,1 3 10 180-200 35-40
1,5 3 10 180-200 40-50
1,0 3 10 180-200 40-45
1,0 3 15 220 15-20
/ 0,5 3 15 180 30-35
1,1 3 15 180 30-35
1,0 3 15 180 45-50
1,0 3 15 180 35-40
20
RS
! -
.
-
, .
,
-
, .
-
.
-
( ).
/ .
, /
; ,
.
.
(., -
) .
, .
1 ( ) 2 -
1 ( ).
.
, -
.
,
.
*,
.
/ ,
.
(, ..) -
.
-
: -
.
, -
«”»,
.
,
, -
: .
* .
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
-
, .
, -
. , -
,
.
.
.
( ) , -
,
.
,
.
! -
.
.
-
.
2002/96/EC
-
(WEEE) -
:
,
.
,
-
.
-
-.
Э
.
-
, :
.
•
•
•
•
•
•
•
•
•
•
This manual suits for next models
2
Table of contents
Languages:
Other Indesit Cooker manuals
Indesit
Indesit KD6G25SAIR User manual
Indesit
Indesit IT50G User manual
Indesit
Indesit KJ1G1/R Quick start guide
Indesit
Indesit IT50G User manual
Indesit
Indesit KD6E35W User manual
Indesit
Indesit KG 3044 BE/G User manual
Indesit
Indesit I5GG10F User manual
Indesit
Indesit ID67G0MCB/UK User manual
Indesit
Indesit KN3T62SA/NL User manual
Indesit
Indesit IT50C1 User manual
Indesit
Indesit KD3C1/G User manual
Indesit
Indesit K 3G2/G User manual
Indesit
Indesit KN6 G110SA/NL User manual
Indesit
Indesit KP 59 MS.C (X)/G Operating manual
Indesit
Indesit ID5G00KMW/UK/L User manual
Indesit
Indesit KD6C0E User manual
Indesit
Indesit KD6G25M User manual
Indesit
Indesit I5GS1G/NL User manual
Indesit
Indesit KD6G25A User manual
Indesit
Indesit K6G2S/FR S User manual
