Infinite Peripherals DPP-350 User manual

DPP–350 Mobile Printer
User Manual
2-inch Mobile Printer

DPP-350 User Manual
2
Contact Information
Mobility Sales/ Technical Support Center
Infinite Peripherals, Inc.
17681 Mitchell N
Irvine, CA 92614
Toll-Free: [phone]
Office: [phone]
Website: ipcmobile.com
Headquarters/ Main Warehouse
Infinite Peripherals, Inc.
2312 Touhy Avenue
Elk Grove Village, IL 60007
Toll-Free: [phone]
Office: [phone]
Fax: [phone]
Legal Notice
“Made for iPhone” (MFi) means that an electronic accessory has been designed to connect specifically to the iPhone and has been
certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note that the use of this accessory with an iPhone may affect wireless
performance.
Trademarks
Infinite Peripherals, Mobilize Your Enterprise, Linea Pro, Infinea Tab, and Infinea Omni are trademarks of Infinite Peripherals, Inc. All
other trademarks are the property of their respective owners.

DPP-350 User Manual
3
Table of Contents
Contact Information 2
Legal Notice 2
Trademarks 2
Overview 4
Guidelines for Use 4
Environmental 4
Mechanical 4
Technical Specifications 6
Box Contents 7
Getting Started 8
Developing Applications 8
Accessories 8
Product Overview 9
Charge Your DPP-350 10
LED Status 10
Replace the Battery 11
Status and Operational Modes 11
Using Your DPP-350 12
Installing a Paper Roll 12
Diagnostic Self-Test 12
DIP Switch Location 13
DIP Switch Settings 13
Memory Switch Settings 14
Set-up the Hardware Memory Switch 14
Memory Switch Configuration 14
Communication Configuration 14
Bluetooth Pairing 15
Pair Your iOS Device 15
Pair Your Android Device 15
(Optional) Magnetic Stripe Reader 16
Battery Disposal 16
Replacing the Battery 16
Resident Command Set 17/18
Troubleshooting 19
Servicing Your Printer 19
Product Returns & Servicing 19
Disclaimer 20
Warranty 20
Symbols 20
Federal Communications Commission 21

DPP-350 User Manual
4
Overview
With the DPP-350 mobile printer you can print data from your smart phone via Bluetooth. Before using the printer, ensure the battery is
fully charged.
Guidelines for Use
Environmental
To prevent printer failure and/or serious personal injury, avoid using the mobile printer under these conditions:
• Anywhere the printer may be exposed to dust, moisture, or direct sunlight/heat.
• Slanted surfaces or surfaces subject to shocks or vibrations.
• Temperatures exceeding 60 degrees C or less than -20 degrees C, or with relative humidity of 85% or more.
• Areas subject to electromagnetic noise or corrosive gas.
• If condensation exists on the mobile head, turn the power off until the condensation evaporates completely.
Mechanical
To prevent the heating elements and driver’s integrated circuit (IC) from exposure to static electricity, use caution when handling the
mobile head.
To prevent damage and/or contamination, avoid the following:
• Touching the dot line on the mobile head/driver IC with metal, sandpaper, or your ngers.
• Volatile chemicals, such as thinners or benzene for maintenance work.
• Opening the paper during printing.
• Pulling the paper out of the printer forcibly when the printer cover is closed.
• Loose paper or paper blocking exit tray may cause the paper to jam.
Note
If the paper jams in the paper exit tray, turn off the power to the printer.
• Do not attempt to disassemble or repair the printer, AC adapter, or power cord yourself. Contact Innite Peripherals at
https://ipcmobile.com/support/support-form

DPP-350 User Manual
5
Electrical
Turn off the printer and disconnect the AC adapter from the power outlet when/IF these happen:
• Smoke, odd smells, or unusual noises are emitted by the printer.
• Metallic objects are dropped, or any liquid is spilled inside the printer.
• Printer is not in use.
Important: Do Not
• Connect or disconnect the AC adapter with wet hands as this can result in electric shock, short circuit, and failure.
• Use any AC adapter or power cord or place heavy objects on top of the printer as this may cause damage to the cord and/or create a re or electric
shock.
• Bend the power cord or place heavy objects on top of it as this can cause damage the cord and/or cause re or electric shock.
• Drop any metallic objects or spill liquids such as coffee, water into the printer.
• Do not touch the head as it is hot after printing. Ensure the thermal head is cool before replacing the paper or cleaning the printer head.
• Remove the cable or adapter from the connector or the receptacle by gripping the connector or the plug. In addition, never pull the cable itself since
this may cause damage to the cable and/or adapter.
Operational
Use only specified paper or equivalent in your printer. Other paper can reduce the life of the printer head and decrease the printing
quality. Store the paper in a cool, dry, and dark location.
Note
Any substances with Sodium (Na+), Potassium (K=), or chlorine (CI-) can reduce the life of the printer head remarkably.
Ensure the paper is stored in a cool, dry, dark place. We recommend you do not expose the paper to bright light for extended periods
of time, organic solvents, or vinyl chloride film, erasers, or adhesive tapes. In addition, do not store the paper in high temperature or
humidity environments, damp areas or areas with exposure to direct sunlight. If pasting printed pages, only use water-based glue, that
is starch glue, synthetic glue, and so forth.
Important: Do Not
• Store the paper on diazo print paper or on wet, freshly made paper copies.
• Handle the paper with wet hands or hard objects since it can cause tears, ngerprints, or smudges.
• Expose the paper
* To bright light or extended periods of time.
* To organic solvents.
* To vinyl chloride lm erasers, or adhesive tapes.
• Store the paper
* In high temperatures, high humidity, damp areas.
Note
If the printer is used continuously under improper conditions can lead to failure, fire, and/or electric shock. This may void your
warranty. If a fault condition continues, contact https://ipcmobile.com/support

DPP-350 User Manual
6
Technical Specifications
Printing
Printing Method Line thermal dot printing
Printing Speed 60mms/s (480 dots per second) at 8.5V
Print Width 72mm/576 dots per line
Resolution 203dpi (8 x 9 dot/mm)
Dot Pitch Horizontal and vertical: 0.125mm (8 dots/mm)
Resident Fonts A: 12 x 24 dots (48 char per line)
B: 9 x 16 dots (64 char per line)
Loadable Fonts C: 12 x 24 (48 char per line)
D: 9 x16 dots (64 char per line)
Logo Registration One black and white with 576 x 248 dots
Input Buffer 36,864 bytes
Resident Barcodes 1D: EAN13, EAN8, UPC-A, UPC-E, Codebar, Code39, Code128
2D: PDF417, QR Code
Emulation ESC/POS Continuous Paper Mode
Thermal Paper 78mm +0/-1mm x 50mm diameter
57mm x 50mm diameter (Optional)
Reliability Printing head: 50km
Printing rate: 25% maximum
Physical
Compatibility Apple iOS devices, Window O/S, Android O/S
Dimensions W x D x H 118mm x 90mm x 51mm (4.6” x 3.5” x 2”)
Weight 340 grams ( oz) - Without paper
430 grams ( oz) - With paper
Electrical
Battery Capacity User-replaceable, rechargeable Li-ion battery
7.4V / 110mAH
Battery Life ~30,000 lines per charge
Power Supply AC adapter: DC 9V, 1A
AC 100-240V 13.A, 50/60 Hz
Magnetic Stripe Reader (Optional) 3-track unencrypted read head, ISO7811
Connectivity (Optional) Bluetooth 2.0 class 2 SPP
(Optional) Bluetooth 3.0 class 2 SPP, iPod accessory protocol
mini USB port
RS232 C 115200bps maximum serial port
Environmental
Operating Temperature
Relative Humidity
+0°C to +45°C (32°F to +113°F)
35% to 85%
Storage Temperature
Relative Humidity
-20°C to +60°C (-4°F to +140°F)
10% to 90%

DPP-350 User Manual
7
Box Contents
• Before using your DPP-350 printer, remove the printer and all included accessories from the shipping carton and verify the contents
against the packing list.
• Retain all packing materials, invoice, and bill of lading. This may be required to return the unit for servicing later, or to process a claim
with the shipping carrier.
• Inspect carefully the contents inside the box carefully for any signs of damage. Do not use if any sign of damage. Notify your Innite
Peripherals account executive or contact technical support at https://ipcmobile.com/support/technical-services
• Ensure the battery pack is fully charged before rst use.
DPP-350 Printer / Belt Clip (1) / Battery Inside
AC Charger (1)
RS-232 Interface Cable (1)
Note
Box contents and SKUs vary based on your order configuration.
Roll of Thermal Paper(1)

DPP-350 User Manual
8
Getting Started
Refer to these sections to help you get the DPP-350
printer ready for use:
What to do Section
Charge the DPP-350
Lithium-ion battery pack
fully before first use.
Charging Your DPP-350
Load DPP-350 print
media, that is thermal
paper.
Using Your DPP-350
Install software from
the SDK onto your
mobile device to use the
features of the printer.
Developing Applications
Set-up Bluetooth pairing
to communicate with the
printer.
Bluetooth Pairing
Developing Applications
Software is not provided with your mobile printer. Please
contact your reseller or Infinite Peripherals for Third Party
software solutions.
Integrating the printer with your mobile application requires
the use of the Infinite Peripherals Software Developers
Kit (SDK). The SDK incorporates an API specifically
for developing applications to use the magnetic strip
functionalities of the mobile printer.
To download the InfineaSDK or IPCMPPrinterSDK, access
our Development Portal at https://developer.ipcmobile.com/
Accessories
Visit our website at https://ipcmobile.com or contact your
Infinite Peripherals account representative for additional
information about our current and future product
accessories.

DPP-350 User Manual
9
Product Overview
Magnetic Card Reader
(Optional)
Paper Feed (LF)
Paper Cover Lever
Serial RS232 Port
Smart Card Reader
(Optional)
Contactless Card Reader
(Optional)
Charger Input
Power On/Off Button
Online/Error LED
(STATUS)
Mini USB Port
Reader LED
Charging LED

DPP-350 User Manual
10
Charge Your DPP-350
Before operating the DPP-350 printer, install the Lithium Ion rechargeable battery. Ensure the battery pack is charged for at least 4
hours.
Note
Ensure the input cord is connected to the AC adapter before charging the battery.
To prevent electrical damage to your printer and/or battery pack, only use the approved AC charger provided with the printer.
1. Pull the DC jack port tab backwards.
2. Insert the AC adapter into the port.
3. Introduce the AC adapter plug into an appropriate power outlet to begin charging.
Note
LED status during charging is displayed.
LED Status
After the initial battery charge is completed, you can monitor the battery status, as needed. If the operating time of a fully charged
battery is too short, you may need to replace the battery.
Solid Red = Charging
Solid Green = Fully Charged

DPP-350 User Manual
11
Replace the Battery
1. Open the battery compartment cover on the bottom of
the printer by rotating the two locking levers.
2. Remove the battery cover.
3. Lift the battery upwards from the compartment carefully.
4. Pull the battery connector wires to detach the battery
connector gently.
5. Replace the cover.
Note
Dispose of used batteries in accordance with Federal law.
This may include disposing them at a recycling center or
hazardous waste collection site.
Status and Operational Modes
The LEDs on the printer indicate the modes of operations.
LEDs illuminate information about the connection status,
charging and/or low battery status.
The statuses and descriptions are
LED Color Description
Red
Solid
Battery charging, or
Paper is out or at the end
Green
Solid
Battery charging complete
Power is on
Green
Flashes 1 per sec
Low battery
Red flash
Green flash
Printer head is overheating

DPP-350 User Manual
12
Using Your DPP-350
Installing a Paper Roll
Before replacing the paper roll or closing the cover, ensure
the mobile head is cool. The mobile head may be very hot
immediately after printing.
Note
Touching the mobile head while hot may result in burn
injuries.
1. To open the printer cover, lift the paper cover up.
2. Place a new paper roll into place.
Note
Ensure at least 12mm or more of the media is above the
top of the printer before closing the printer cover.
3. Use both hands to close the paper cover to ensure it is
closed completely.
4. Close the paper cover until you hear the lock into place.
Diagnostic Self-Test
The built-in test pattern shows the DPP-350 printer’s
current configuration and resident fonts. The self test
is used for troubleshooting and helps you determine
printing issues or battery statuses.
LP button operation modes are completed when the
print is turned on:
Action Result
1. Hold LP for ~0.5
second.
2. Release after
one beep.
Short self text prints automatically
3. Hold LP for ~2.5
seconds.
4. Release after
two beeps.
Hex dump mode
All input data is printed as
hexadecimal
5. Hold LP for 8.5
seconds.
6. Release after
the fth beep
(long 4-tone).
Program mode
Loads printer firmware
7. Hold LP for ~4
seconds.
8. Release after
one beep.
Forces 9600 bps serial speed
temporarily
9. Hold ON button
for ~6 seconds.
Hardware set-up mode
Long Self Test
When the printer is turned on, press and hold the LP button.
Release after 4.5 seconds when you hear three beeps. A long
self test prints with information about these criteria:
• Resident font sizes
• Characters per line
• Text formatting
• Resident character set
• Resident barcode symbols
• Printer conguration

DPP-350 User Manual
13
DIP Switch Settings
With the different methods of communication designed
in the DPP-350, ensure the DIP switches remain as the
factory default, unless required for change. Two different
operational modes, which detect current conditions
differently, and are determined by the SW2 switch:
• Continuous Paper Mode.
• Black Mark Mode — Determines the proper alignment
for the starting print position on indexed media with
printed data.
Switch Off On
SW1 Enable Bluetooth Disable Bluetooth
SW2 Continuous Paper
Mode Black Mark Mode
SW3 None Xon / Xoff protocol
SW4 Normal operation
mode Protocol mode
DIP Switch Location
1. To locate the DIP switch settings, turn the printer to the
back side, and rotate the two locking levers (see 1a & 1b).
2. To remove the battery cover, lift it upwards.
3. Remove the battery.
4. Turn the desired switch On or Off, as needed.

DPP-350 User Manual
14
Memory Switch Settings
Non-volatile memory is used in storing the printer’s default
configuration settings.
Note
If you change any factory preset configurations, verify the
settings are correct.
The available options are:
Memory Switch Options
Memory switch (GS command) 1000000010
Baud Rate 115200 bps
Auto Off Time 10 minutes
Print Darkness 100%
Character Table Western (1252)
USB Device Class Printer
Set-up the Hardware Memory Switch
1. Turn the printer Off (ERR LED is off) before proceeding.
2. Press and hold down the Power button. ERR LED ashes
red and green every second.
3. Release the On button after approximately 6 seconds.
4. Wait for the Out of Current Memory settings page to
print, and then follow the instructions from the printer
and make any necessary changes.
* Press LF (Yes) to accept changes.
* Press On/Off (No) to cancel changes.
Memory Switch Configuration
Ten memory switches are available on the DPP-350.
Memory
Switch Description
SW1 Enable/disable buzzer
SW2 Disable CR
CR executed as LF
SW3 Enable/disable LF
SW4 LF after CR
Disable LF after CR
SW5 Font A (12x24)
Font B (9x16)
SW6-7 Reserved for future use
SW8 Enable - Prevents others from
discovering printer
Must be set after pairing finished
SW9 Enable/disable USB
USB port for communication is
allowed
SW10 (Off) Set USB for Host/Device mode
Communication Configuration
The configuration methods for communication using the
DPP-350 are via your smart phone or Bluetooth.
Note
If not using a driver or the SDK developer tools, set DIP
switch 4 to OFF.
* Indicates 1 or 0 may be used based on user requirements.
• Memory switch options 1-10: *******010
• Physical switch options DIP switch (1,2,3,4): *, Off, Off,
On
Configuration methods for communication with a personal
computer using a Windows printer driver and via Bluetooth,
USB, or Serial (SPP).
• Memory switch options 1-10: *******011
• DIP switch options 1,2,3,4: *, Off, Off, Off
Configuration methods for service mode to change printer
settings, load firmware, and communicate with a personal
computer or via SPP.
• Memory switch options (1-10): *******011
• DIP switch options 1,2,3,4: *, Off, *, On

DPP-350 User Manual
15
Bluetooth Pairing
Pair Your iOS Device
1. Enable Bluetooth on your iOS device.
2. To pair, select DPP-350 under Devices. The blue LED on
the printer blinks when the devices are connected.
3. Start the Library Demo app, and then select Print self test
to verify the Bluetooth connection.
Pair Your Android Device
1. Enable Bluetooth, and then search for available devices.
2. Once DPP-350 is displayed under Available devices, you
can pair it, and tap 0000 as the default pin.
3. After pairing is successful, open the Printer Sample app.
4. Select a device to connect either by tapping the
Bluetooth address for the DPP-350 or scan for devices.
5. To test the Bluetooth connection, tap Print self test.

DPP-350 User Manual
16
(Optional) Magnetic Stripe Reader
The built-in magnetic card reader incorporates a 3-track magnetic read head requiring a single swipe to capture field data from all three
tracks. The magnetic card reader is in the front of the printer.
Before using the magnetic strip reader, you must install the software to read and process the card data. Contact your Infinite
Peripherals or refer to https://developer.ipcmobile.com/
1. To read a magnetic stripe card, place the card with the stripe facing backwards.
2. To ensure the stripe passes over the read head Evenly.
3. Keep the bottom edge of the card at on the inner base of the reader.
4. Swipe the card evenly from start to nish, with the speed of the swipe consistent to accurately read the data on the card.
Magnetic Card Reader
Magnetic Strip
(Face this direction)
Card Swipe Direction

DPP-350 User Manual
17
Resident Command Set
Command Command
1 BLE Sounds Buzzer 41 ESC D Set horizontal tab position
2 HT Horizontal Tab 42 ESC E Set/cancel emphasized mode
3 LF Print a line/Paper feed 43 ESC F Fill/invert page are page mode
4 FF Print/paper to black mark position 44 ESC G Set/cancel double-strike mode
5 CR Based on flags 2,3,4 45 ESC I Set/cancel italic print
6 DC2= Image LSB/MSB selected 46 ESC J Print paper feed n/203”
7 DC3( Start Ruled Line Sequence 47 ESC L Set page mode
8 DC3+ Ruled line On 48 ESC N Read programmed serial #
9 DC3- Ruled line Off 49 ESC R Select country
10 DC3A Ruled Line A 50 ESC S Set serial port bps speed
11 DC3B Ruled Line B 51 ESC T Print short self-test
12 DC3C Clear ruled line buffer 52 ESC U Set/cancel underlined printing
13 DC3D Set single dot in ruled line buffer 53 ESC V Set/cancel 90°right turned char print
14 DC3 F Ruled line pattern set 54 ESC W Set max print speed
15 DC3 L Ruled line set 55 ESC Y Set intensity level
16 DC3 M Ruled line combination mode 56 ESC X Set maximum print speed
17 DC3 P Ruled line 1 dot line print 57 ESC Z Return diagnostic data
18 DC3 p Ruled line n dots line print 58 ESC \ Set relative horz position
19 DC3 v Ruled line image write 59 ESC ] Load default settings from flash memory
20 CAN Canceling print job in page mode 60 ESC ^ Save current settings in flash memory
21 ESC FF Print data in page mode 61 ESC_ Load factory settings
22 ESC RS Buzzer sounds 62 ESC Read battery voltage/thermal head temp
23 ESC SP Set character spacing 63 ESC a Align characters
24 ESC # Set Euro symbol position 64 ESC b Print increase text line height
25 ESC $ Specify absolute horizontal print position 65 ESC c5 Enable/disable LF button
26 ESC % Set/cancel download printing char set 66 ESC d Print/feed paper by n-lines
27 ESC & Set/cancel character set 67 ESC i Feed paper backwards
28 ESC ! Specify text print mode 68 ESC o Temp feed paper forward
29 ESC * Print graphics 69 ESC pair= Enable/disable pairing/save BT mode
30 ESC + Switch off the printer 70 ESC pwd= Program new BT PIN
31 ESC - Set/cancel underlining 71 ESC r Full command for buzzer
32 ESC . Print self-test/diagnostics 72 ESC s Read printer settings
33 ESC 2 Specify 1/6” line feed rate 73 ESC u Set code table
34 ESC 3 Specify line feed rate n/203” 74 ESC v Transmit printer status
35 ESC < Change to opposite print direction 75 ESC x Set time interval automatically turn off printer
36 ESC = Data input control 76 ESC y Set USB response strings
37 ESC > Set print direction 77 ESC { Set/cancel 180° turned characters print
38 ESC ? Read magnetic stripe card 78 GS FF Print page mode/return to standard mode
39 ESC @ Initialize printer 79 GS $ Specify page mode absolute vertical position
40 ESC CAL Black mark mode sensor calibration 80 GS ) Set printer flags/memory switches

DPP-350 User Manual
18
Resident Command Set
Command Asian Language Support Commands
81 GS / Print downloaded bit image 106 FS ! Set 2-byte text data print mode
82 GS * Define downloaded bit image 107 FS & Select 2-byte text mode (JIS or GB2312)
83 GS : Start/end macro definitions 108 FS - Set/cancel 2-byte underline text mode
84 GS B Enable/disable inverse white/black print 109 FS . Cancel 2-byte text mode
85 GS C Read realtime clock 110 FS C Set shift-JIS mode - Japanese version only
86 GS H Set HRI code print position 111 FS S Set 2-byte character spacing text mode
87 GS L Set left margin 112 FS W Set 2-byte double size character text mode
88 GS Q Print 2D barcodes
89 GS R Fill/invert page mode rectangle
90 GS S Set 2D barcode cell size
91 GS T Set page mode print direction
92 GS U Set standard mode
93 GS W Set print area width
94 GS X Draw standard thickness page mode rectangle box
95 GS Z Print page mode non-blank page area
96 GS \ Set page mode relative vertical position
97 GS^ Execute macro
98 GS c Set realtime clock
99 GS f Set HRI char barcode font
100 GS h Set barcode height
101 GS k Print barcode
102 GS p Set PDF417 2D barcode
103 GS q Set 2D barcode PDF 417 module height
104 GS w Set barcode scale factor/horizontal size
105 GS x Page mode direct text print

DPP-350 User Manual
19
Servicing Your Printer
When your printer requires servicing of any type, contact
your Infinite Peripherals account manager.
Important
Do not attempt to disassemble or repair your printer, AC
adapter, or power cord as this can void your warranty. Refer
to Product Returns and Servicing for information.
Troubleshooting
These troubleshooting guidelines can assist you in the
successful installation and configuration of the DPP-350
mobile printer. If you are having problems operating your
printer, first verify that there is power to the printer and that
it is powered on and sufficiently charged.
Once power and proper battery charge is confirmed, review
Troubleshooting for additional information. If a problem
persists or the problem is not described here , contact
technical support at https://ipcmobile.com/support. Your unit
may need to be returned for servicing.
Refer to Charging Your DPP-350 for additional information on
charging your printer.
Problem Reason / Solution
Paper feeds
after print job
command but
text not visible
on paper.
Thermal paper may not be loaded with
coating on outside of the roll.
Remove paper roll and then reload
correctly. Refer to the Installing a Paper
Roll section for details.
ERR LED
blinks red
continuously.
Paper cover may not be install
properly.
Printer may be out of paper or not
loaded correctly.
Text and/or
images are
printed too
lightly.
Battery voltage may be low. Refer to
Charging Battery Pack. Verify thermal
paper is the recommended media.
Non-standard
characters
print.
Battery voltage is low. Refer to the
section, Charging Your DPP-350.
Printer does
not respond to
print/paper feed
commands.
Reset printer:
Remove battery for 5 seconds, and then
reinstall battery into printer.
Text is too
light to read or
text is missing
on half of the
printed width.
Paper cover is not installed properly.
Refer to the Installing a Paper Roll
section for details. Printer components
are loose. Contact https://ipcmobile.
com/support
Product Returns & Servicing
Use the link in step 1 to create an account and gain access
to our Knowledge Base and online support services. Through
our online support center, you’ll be able to download files,
open a Support Ticket, manage your RMAs, view your
account Profile and subscribe to Alerts.
To request a RMA
1. Create a user account in the RMA Support Portal at
http://ipcmobile.com/support/rma/
2. Login to your user account, and then click Create RMA
Request.
3. Read the instructions provided and complete the online
request form.
4. Note the assigned RMA number and write it clearly on
your shipping carton.
5. Ship your equipment back to us using the address
provided.

DPP-350 User Manual
20
Warranty
Infinite Peripherals does not warrant, and is not responsible
for, any damage to the DPP-350 (“Product”) as a result of
liquid or solid particle intrusion into the Product, or damaged
caused by dropping the Product with the assembled iOS
device. If a material or workmanship defect arises with
regard to any Infinite Peripherals product, and a valid claim
is received within the Warranty Period, Infinite Peripherals
(at our sole discretion) will repair the Product using new
or refurbished parts, or replace the Product with a new or
refurbished Product.
For purposes of this limited warranty, “refurbished” means
a product or part that has been substantially returned to
its original specifications. In the event of a defect, these are
your exclusive remedies.
Disclaimer
NO WARRANTY. This technical documentation is provided
AS-IS. Further, the documentation does not represent a
commitment on the part of. Infinite Peripherals, Inc does
not warrant that it is accurate, complete or error free. Any
use of the technical documentation is at the risk of the
user. Infinite Peripherals, Inc reserves the right to make
changes in specifications and other information contained in
this document without prior notice, and the reader should
in all cases consult Infinite Peripherals, Inc to determine
whether any such changes have been made. Infinite
Peripherals, Inc shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental
or consequential damages resulting from the furnishing,
performance, or use of this material. Infinite Peripherals,
Inc does not assume any product liability arising out of or
in connection with the application or use of any product or
application described herein.
Symbols
Symbol Description
Refer to the instructions before using
this product
Manufacturer
Manufacture Date
Caution
Serial Number
P/N Part Number
Waste Electrical and Electric Equipment
Complies with part 15 of the FCC rules