Infinity Total Solutions TSS-FMK4000 User manual

TSS-FMK4000
Owner’s Guide
TOTAL SPEAKER SOLUTIONS
TSS-4000
INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 1

2TSS-FMK4000
INTRODUCTION
The TSS-FMK4000 allows you to recess a TSS-SAT4000 or
TSS-CENTER4000 into the wall. When installed, the speaker
will extend beyond the wall approximately 1."
Unpacking the Components
Finish unpacking the flush-mount kit and check the contents. If
you suspect damage from transit, report it immediately to your
dealer. Keep the shipping carton and packing materials for
future use.
Contents
Please verify that the package contains the following items:
(1) 3/16"-Thick Cardboard Template
(1) Speaker Frame
(2) End Brackets
(2) Mounting Blocks
(2) Sealing Strips
(4) #8 x 1" Flat-Head Wood Screws
(4) #8 x 1-1/8" Pan-Head
Wood Screws
(2) 1/4-20 x 3/4" Flat-Head
Machine Screws
INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 2

3
TSS-FMK4000
Step One
Remove both end caps of the speaker by unscrewing the single
center screws.
Step Two
Attach both of the end brackets to the speaker ends with the
1/4-20 x 3/4" flat-head machine screw, as shown.
End Bracket
End Bracket
1/4-20 x 3/4"
Flat-Head
Machine Screw
1/4-20 x 3/4"
Flat-Head Machine Screw
Speaker
End Cap
Center Screw
1/4-20 x 3/4" Screw
Important Notes:
1) In order to horizontally flush-mount the TSS-CENTER4000 in a wall
with standard 16" spacing between the studs, some modification to
that area of the wall will be necessary.This type of installation will
require a professional licensed contractor to install horizontal braces
that comply with the customer’s local building codes.
2) For a satellite installation, follow all the steps but cut the hole
in a vertical direction, perpendicular to the floor. See exploded view
on page 7.
INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 3

4TSS-FMK4000
Step Three
After you have found the correct placement on the wall for the
speaker, use the template provided to draw the exact-sized hole
required. Make sure to use a level when positioning the template
to ensure that your installation is level.Then cut out the drywall
to create the hole.
Step Four
Place the mounting blocks inside the hole at either end. Use two
#8 x 1" flat-head wood screws to secure them in place.
(4) #8 x 1"
Flat-Head
Wood Screws
Screw Holes
Wall
Template
Mounting Block
Mounting
Block
NOTE: The hole for
the speaker should be
22-1/2" x 4-3/8."
INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 4

5
TSS-FMK4000
Step Five
Attach speaker wires as described in the speaker’s owner’s
manual and, using four #8 x 1-1/8" pan-head wood screws
provided, screw the speaker assembly into place, making sure
that the screws anchor themselves into the mounting blocks
behind the drywall.
Step Six
Apply the sealing strips to either side of the speaker to cover the
remaining openings of the cutout in the drywall.
(4) #8 x 1-1/8"
Pan-Head
Wood Screws
Sealing Strip
INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 5

6TSS-FMK4000
Step Seven
Remove the paper cover from the gasket on the speaker-facing
side of the frame. Place the frame over the in-wall assembly and
snap it into place.
Remove Paper Cover
From Gasket
Frame
Center Speaker In-Wall Installation
INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 6

7
TSS-FMK4000
Satellite Installation Exploded View
For satellite installation, repeat the steps but cut the hole in
a vertical direction, perpendicular to the floor.
Satellite Speaker
In-Wall Installation
INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 7

© 2004 Harman International Industries, Incorporated
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4INF (USA only)
www.infinitysystems.com
Infinity is a registered trademark, and Total Solutions is a trademark, of Harman International Industries, Incorporated.
Part No. 400-OMINKIT 10/04
Infinity continually strives to update and improve existing products, as well as create new ones.
The specifications and construction details in this and related Infinity publications are therefore
subject to change without notice.
INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 8