Infoblox 4005 series User manual

Infoblox Installation Guide 4005 Series Appliances

Trinzic TE-4015 and TE-4025

Network Insight ND-4005

Trinzic Reporting TR-4005

Introduction to the Infoblox 4005 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1 Infoblox Trinzic TE-4015 and TE-4025 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Infoblox Network Insight ND-4005 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Infoblox Reporting TR-4005 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Infoblox 4005 Series Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 System, Environmental, and Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6 DC Power Cable Color Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Accessing the Infoblox 4005 Series Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1 Connecting To The Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2 Auto Provisioning NIOS Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3 Specifying Appliance Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4 Infoblox NIOS CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installing the Infoblox 4005 Series Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1 Rack Mounting Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2 Powering the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3 Cabling the Appliance to a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Field Replaceable Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1 Managing the Disk Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2 Hard Disk Drive Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3 Replacing Fan Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4 Changing AC Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5 Changing DC Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6 International AC Power Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Introduction to the Infoblox 4005 Series

This guide provides an overview of the Infoblox 4005 Series appliances, and explains how to install and configure the system. The Infoblox 4005

Series includes the Infoblox Trinzic TE-4015 and TE-4025, the Network Insight ND-4005, and the Trinzic Reporting TR-4005. This guide

describes the features for each appliance model, the hardware elements, and installation and deployment information common to all models in

the Infoblox 4005 series. Consult the respective sections below for introductory descriptions of the unique features for your specific appliance:

Infoblox Trinzic TE-4015 and TE-4025 Product Overview

Network Insight ND-4005 Product Overview

Infoblox Reporting TR-4005 Product Overview

You configure and manage Infoblox 4005 Series appliances through the easy-to-use Infoblox GUI, Grid Manager, that works seamlessly in

Windows, Linux, and Mac environments using standard web browsers. For more information about Grid Manager, refer to the Infoblox NIOS

.Administrator Guide

The 4005 Series appliances are Class A and Class B (with limits) digital appliances per FCC regulations, and are RoHS compliant, and WEEE

compliant.

Infoblox Trinzic TE-4015 and TE-4025 Product Overview

The Infoblox Trinzic TE-4015 and TE-4025 are high performance network appliances that provide core network services, including DNS (Domain

Name System), DHCP (Dynamic Host Configuration Protocol), IPAM (IP Address Management), and NTP (Network Time Protocol). They may

operate as a Grid member or as a Grid Master, and can operate with a second Trinzic appliance of the same model in high availability (HA) mode.

You configure and manage the Trinzic appliances through the Infoblox Grid Manager.

Key features of the TE-4015 and TE-4025 include the following:

Support for Grid management and all administrative features for Infoblox IPAM, DNS, DDNS, and DHCP.

Optional 10GbE or 1GBE SFP+/SFP system configurations for fiber or copper support.

High availability support.

LOM (Lights Out Management) support.

Field replaceable hard disk drives and fan modules.

Hot-swappable AC supplies

Optional DC power supplies

CC and FIPS for TE-4015, TE-4025, TE-V4015, and TE-V4025

The Infoblox Trinzic TE-4015, TE-4025, TE-V4015, and TE-V4025 appliances can be made compliant with CC (Common Criteria) and FIPS

(Federal Information Processing Standard) 140-2 security standards. Both CC and FIPS give assurance that the product satisfies a set of

internationally recognized security measures. CC is a set of rules and specifications to evaluate the security of Information Technology (IT)

products. FIPS is a U.S government computer security standard that is designed to validate product modules that use cryptography. This is

necessary to maintain the integrity and confidentiality of the end-user information that is stored, processed, and transferred by the product

module. To ensure that your appliance is CC and FIPS compliant, make sure that your hardware and software settings match the evaluated

configuration that was certified for both CC and FIPS. For information about how to configure CC and FIPS, refer to the Infoblox NIOS

.Administrator Guide

Infoblox provides tamper evident FIPS labels that you must affix on the HDD cover, all PSU and fan canisters, over the IPMI port of the appliance

to make it FIPS compliant. You must install the FIPS tamper evident labels correctly onto the device for compliance with FIPS. This label is valid

for Infoblox Trinzic TE-4015 and TE-4025 appliances only. Note that these labels are not required for CC.

Clean the chassis before affixing tamper evident FIPS labels. Apply these labels as shown in the figures below:

FIPS label

Install a sticker on the drive bay cover as shown in the picture

Install a sticker on both of the back corners of the top cover as shown in this picture

Install stickers for each of the fans into the chassis as shown in this picture

Install a sticker for each power supply module as shown in this picture

Install a sticker covering the IPMI port as shown in this picture

Infoblox Network Insight ND-4005 Product Overview

The Network Insight ND-4005 is a high performance network appliance that supports device discovery and network discovery features, using

SNMP and other protocols to discover, query, manage and catalogue network devices such as enterprise Ethernet switches, routers, firewalls and

other security devices, VoIP softswitches, load balancers, end host devices and more. You configure the ND-4005 appliance through Infoblox

Grid Manager. For more information about the Discovery features, refer to the Infoblox NIOS Administrator Guide.

Key features of the Network Insight ND-4005 appliance include the following:

Three (3) active 1GbE Ethernet interfaces: two (2) active interfaces to support Device Discovery features, and one interface (MGMT) for

device management. (The HA port is inactive and reserved for future use.)

Optional 10GbE or 1GBE SFP+/SFP system configurations for fiber or copper support.

Management through the Infoblox Grid.

LOM (Lights Out Management) support.

Replaceable hard disk drives and fan modules.

Hot-swappable AC or DC power supplies in a redundant 1+1 configuration.

Note: The Network Insight ND-4005 does not support HA operation and acts only as a Grid member.

Infoblox Reporting TR-4005 Product Overview

The Infoblox Reporting TR-4005 is a high performance network appliance that collects data from Infoblox Grid members, stores the data in the

reporting database, and generates reports that provide statistical information about IPAM, DNS, DHCP, and system activities and performance.

You configure and manage the TR-4005 and view its reports through the Infoblox Grid Manager. For more information about Reporting features

and licensing, refer to the .Infoblox NIOS Administrator Guide

Key features of the Trinzic Reporting TR-4005 appliance include the following:

Three (3) active 1GbE Ethernet interfaces: two (2) active interfaces to support event reporting features across the network, and one

interface (MGMT) designated for device management. (The HA port is inactive and reserved for future use.)

Optional 10GbE or 1GBE SFP+/SFP system configurations for fiber or copper support.

Management through the Infoblox Grid.

LOM (Lights Out Management) support.

Replaceable hard disk drives and fan modules.

Hot-swappable AC or DC power supplies in a redundant 1+1 configuration.

Note: The Trinzic Reporting TR-4005 does not support HA operation and acts only as a Grid member.

Infoblox 4005 Series Hardware Components

The Infoblox 4005 Series are 2-U appliances that you can efficiently mount in a standard equipment rack. For information about rack mounting,

see .Rack Mounting Procedures

Front Panel

Infoblox 4005 Series front panel components include communication ports and hard disk drives, as shown in the and described in thefigure table

below. The hard disk drives are concealed under a removable drive bay door. You must remove the door to access the hard disk drives, as shown

in the . For more information, see and .figure Ethernet port LEDs Interface Connector Pin Assignments

Table below describes the Infoblox 4005 Series front panel components.

Front Panel Components

Component Description

Hard Disk Drives Four hot-swappable Infoblox data storage devices configured in a RAID 10 (Redundant Array of Independent Disks)

array. Each disk drive has LEDs on the far left side of each drive carrier,that indicate the connection and activity

status on the disk drive. The top LED flickers green when the disk drive is operational and performing read-write

operations. The lower LED is dark(inactive) during all operations. Both drive LEDs are dark when the disk drive is not

connected.You must use the Grid Manager UI or the NIOS CLI to verify disk operation. For more information, see Ev

.aluating the Status of the Disk Subsystem

On/Off Switch A power switch to turn the power supply of the appliance on and off. The switch is hidden. Usea small blunt object,

such as a paper clip, to gently push the switch.

Power LED An LED that glows green when there is power to the appliance. When it is dark, the appliance is not receiving power,

even if the power cable is plugged in. When it glows red, there is an error. Ensure that you power on the appliance

through the On/Off switch using a small blunt object, such as a paper clip.

USB Port Reserved for future use.

IPMI Port Dedicated Ethernet port used for LOM (Lights Out Management) with specific releases of NIOS.The IPMI/LOM Port

supports 10/100/1000 Mbps operations. Ensure that the IPMI port is properly connected to the network before you

configure LOM through the Grid Manager for remote management. The IPMI port auto-negotiates up to Fast Ethernet

100BASE-TX speeds; ensure that the switch port to which the IPMI port connects will auto-negotiate to 100Mbps

operation.Follow best practices for IPMI usage in the network by not allowing the IPMI port to connect to the

general-use data center network or to 1 Gbps/10 Gbps switch interfaces.

MGMT Port A 10/100/1000-Mbps gigabit Ethernet port for appliance management, or for appliance services on the network. You

enable the MGMT port and define its use through the Grid Manager after the initial setup.

LAN1 Port A 10/100/1000-Mbps gigabit Ethernet port that connects the appliance to the network. You use the LAN1 port for

initial appliance setup. The LAN1 port carries all traffic if you do not enable the MGMT and LAN2 ports. The passive

node in an HA pair (supported in the Trinzic2210 and 2220 appliances) uses this port to synchronize the database

with the active node.

Console Port A male DB-9 serial port for a console connection to change basic configuration settings and view basic system

functions through the CLI (command line interface). If your system lacks a DB-9 serial port, use a properly grounded

USB-to-Serial dongle for connection to the serial console port. If the dongle is connected to a laptop, the laptop also

must be properly grounded. Failure to do so may cause damage to the serial console port of the Infoblox appliance.

Infoblox is not responsible for such damage. For DB-9 pin assignments, see DB-9 Console Port and RJ-45 Port

.Pinouts

HA Port (Active for high

availability in the

TE-4015 and TE-4025

appliances)

A 10/100/1000-Mbps gigabit Ethernet port through which the active node in an HA (high availability) pair connects to

the network using a VIP (virtual IP) address. HA pair nodes also use their HA ports for VRRP (Virtual Router

Redundancy Protocol) advertisements. ND-4005 and TR-4005 Reporting Models: The HA Port is inactive and

reserved for future use. See for appliance support details.SFP/SFP+ Interfaces Support Summary

LAN2 Port A 10/100/1000-Mbps gigabit Ethernet port that connects the appliance to the network. The LAN2 port is disabled by

default. You enable the LAN2 port and define its use through the Grid Manager after initial setup.

UID Button The unit identification button. In a rack environment, the UID feature enables easier location of a server when moving

between the front and rear of the rack. You can also identify the appliance through the Grid Manager and CLI

command.

Ethernet Port LEDs

To see the link activity and connection speed of an Ethernet port, you can look at its Activity and Link LEDs. The shows the statusbelowfigure

the LEDs convey through their color and illumination (steady glow or blinking).

Ethernet Port LEDs (inc. SFP+ interfaces where noted)

Category 5 Cable: Up to 100 Mbps

Category 5e/6 Cable: Up to 1Gbps

Label Color Port Status

Activity Blinking Green Link is Up and Active (SFP+ only)

Steady Yellow Link is up but inactive

Blinking Yellow Link is up and active

Dark Link is down

Link Steady Blue 10000 Mbps (SFP+ only)

Steady Amber 1000 Mbps

Steady Green 1000 Mbps

Dark 10 Mbps

Category 5 Cable: Up to 100 Mbps

Category 5e/6 Cable: Up to 1Gbps

SFP/SFP+ Interface Support

All models in the Infoblox 4005 Series support optional interfaces to accept SFP transceiver modules, for 1GbE optical connectivity. The table

summarizes SFP and SFP+ support for appliance models in the Infoblox 4005 Series.below

Note: You cannot add SFP/SFP+ support after you have purchased an appliance model that does not have the SFP/SFP+ interfaces

pre-installed. Contact your Infoblox representatives if you are interested in purchasing appliances that support SFP/SFP+ interfaces.

To support connectivity to 10 Gigabit (10GbE) networking infrastructure, Infoblox also offers versions of the Infoblox TE-4015 and TE-4025,

Network Insight ND-4005 and Trinzic Reporting TR-4005 that provide 10-Gigabit Ethernet (10GbE) interfaces accepting SFP+ transceiver

modules, for 10GbE RJ-45 copper or optical connectivity.

The Infoblox TE-4015 and TE-4025 appliances support four active 10GbE interfaces in the optional 1GbE SFP and 10GbE SFP+ configurations.

Other appliances in the Infoblox 4005 Series, comprising the ND-4005 and TR-4005, support three active interfaces in the optional 1GbE SFP

and 10GbE SFP+ configurations. The port designated HA for these three models is inactive for these appliances. Order of ports from left to right

is otherwise the same.

In optional configurations for the Infoblox 4005 Series (any appliance that does not use the internal Ethernet ports), the Infoblox 1GbE SFP or

10GbE SFP+ ports replace the functionality in the original system MGMT, LAN1, HA and LAN2 ports, thereby disabling the built-in MGMT, LAN1,

HA and LAN2 ports. 10GbE support accepts Infoblox-provided SFP+ 10GbE Short Range and Long Range transceivers, Cisco SFP+ Direct

Attach 10GSFP+Cu, or HP HPJ9283B SFP+ Direct Attach 10GSFP+Cu transceivers.

You may mix media types in the set of ports (e.g., one copper SFP in the MGMT port and two or three fiber SFPs).

SFP and SFP+ transceivers also may be used in a mixed configuration in a 4-Port 10GbE system. One example involves installing 10GbE SR

SFP+ transceivers in the LAN1 and LAN2 ports for the Infoblox Trinzic TE-4015 and TE-4025 appliance, and installing 1GbE SFP copper

transceivers in the MGMT and HA interfaces.

Note: For ND-4005 and TR-4005 models configured with 1GbE SFP or 10GbE SFP+ interfaces, the HA port is reserved for future use and cannot

be used for network applications. Order of ports from left to right is otherwise the same.

SFP/SFP+ Interfaces Support Summary

Infoblox 4005

Series Model SFP/SFP+ Support # of active

SFP/SFP+ ports 10GbE Support Accelerated 10GbE

Support HA Disabled internal

RJ-45 ports

TE-4015 Y14 Y N Y Y2

TE-4025 Y14 Y N Y Y2

ND-4005 Y13 Y N N Y2

TR-4005 Y13 Y N N Y

1– With optional 1GbE or 10GbE line card. Disables internal RJ-45 ports.

2– Only in appliance configurations with optional SFP/SFP+ ports.

See the section for specific information on part numbers, availability, and device compatibility.Field Replaceable Units

Interface Connector Pin Assignments

An Infoblox 4005 Series appliance has three types of ports on its front panel:

USB port (reserved for future use)

Male DB-9 console port

RJ-45 10Base-T/100Base-T/1000Base-T auto-sensing gigabit Ethernet ports

The describes DB-9 and RJ-45 connector pin assignments. The DB-9 pin assignments follow the EIA232 standard. To make a serialfigure below

connection from your management system to the console port, you can use an RJ-45 rollover cable and two female RJ-45-to-female DB-9

adapters, or a female DB-9-to-female DB-9 null modem cable. The RJ-45 pin assignments follow IEEE 802.3 specifications. All Infoblox Ethernet

ports are auto-sensing and automatically adjust to standard straight-through and cross-over Ethernet cables.

DB-9 Console Port and RJ-45 Port Pinouts

DB-9 Connector Pin Assignments

Pin Signal Direction

1 (not used)

2 Receive Input

3 Transmit Output

4 DTE Ready Output

5 Ground —

6 DCE Ready Input

7 RTS (Request to Send) Output

8 CTS (Clear to Send) Input

9 (not used)

RJ-45 Connector Pin Assignments

Pin 10Base-T 100Base-T Signal 1000Base-T Signal T568AStraight-Through Wire Colo

T568BStraight-Through Wire Colo

1 Transmit + BI_DA+ White/Green White/Orange

2 Transmit - BI_DA- Green Orange

3 Receive + BI_DB+ White/Orange White/Green

4 (not used) BI_DC+ Blue Blue

5 (not used) BI_DC- White/Blue White/Blue

6 Receive - BI_DB- Orange Green

7 (not used) BI_DD+ White/Brown White/Brown

8 (not used) BI_DD- Brown Brown

Legend: BI_D = bidirectional; A, B, C, D = wire pairings

10Base-T Ethernet and 100Base-T fast Ethernet use the same two pairs of wires. The twisted pair of wires

connecting to pins 1 and 2 transmit data, and the twisted pair connecting to pins 3 and 6 receive data.

1000Base-T connections use all four twisted-pair wires for bidirectional traffic.

Appliance Rear Panel

The Infoblox 4005 Series appliances ship with dual AC power supplies and six fan modules. The power supplies and fan modules are field

replaceable. The power supplies are also hot-swappable so you can replace any one of them at a time without disrupting the operations of the

appliance.

Infoblox 4005 Series, Rear View

Rear Panel Components

Component Description

Fan Modules Six field replaceable fan modules to help maintain optimum operating temperature. Each fan has an air vent that allows

warm air to flow out of the appliance. Do not obstruct.

UID LED Blue = UID is activated through pressing the UID button on the appliance or through the Grid Manager or CLI command.

Dark = UID is deactivated

UID Button The unit identification button. In a rack environment, the UID feature enables easier location of a server when moving

between the front and rear of the rack. You can also identify the appliance through the Grid Manager and CLI command.

Grounding Post For DC installations, you securely connect a grounding wire to the chassis and to earth ground, which typically is the

equipment rack on which you install the appliance. The mounting nut is placed on the grounding post for convenience.

Remove the mounting nut, place the grounding wire connector onto the grounding post and replace the mounting

nut.Ensure that it is snug.

Power Supplies Each of the two redundant power supplies has a three-prong power outlet for connecting the appliance to a standard AC

(Alternating Current) power source.

System, Environmental, and Power Specifications

System specifications describe the physical characteristics of the Infoblox 4005 Series appliances. Environmental specifications describe Infoblox

4005 Series temperature and moisture limits. Power specifications describe the electrical range within which the appliance circuitry can operate.

This chapter reports power usage and heat generation characteristics against the hardware configuration for the Infoblox 4005 Series appliances.

Optional hardware configurations that affect electrical power budgets include the following:

Use of a single power-supply or 1+1 redundant PSU (power supply unit) configuration (see ).Appliance Rear Panel

1 GbE SFP network interface card (see ).SFP/SFP+ Interface Support

10 GbE SFP+ network interface card (see ).SFP/SFP+ Interface Support

You may choose to order a field-replaceable power supply to upgrade your appliance to a 1+1 redundant configuration. Doing so changes the

power usage and heat generation characteristics for your appliance. The same is true if you change out your AC power supply configuration for

DC power supplies. Consult the specifications for your appliance for both AC and DC information.

System Specifications

Form Factor: 2-U rack-mountable appliance

Dimensions: 88mm H x 441mm W x 534mm D

Weight: Approximately 29 lbs (13.15 kg)

Ethernet Ports: MGMT, HA, LAN1, LAN2 – auto-sensing 10Base-T/100Base-T/1000Base-T

Serial Port: DB-9 (9600/8n1, Xon/Xoff)

USB Ports: USB 3.0

Safety: FCC, CE, TUV, CB, VCCI, C-Tick, KCC, CCC, NOM, BIS, EAC

Environmental Specifications

Operating Temperature: 41°F – 95°F (5 – 35°C)

Storage Temperature: –40°F – 122°F (–40°C – 50°C)

Operating Relative Humidity: 5% to 95% (non-condensing)

Airflow CFM (Cubic Feet/Minute): 203 CFM

Airflow Direction: Front-to-Back

Environmental Certification: WEEE and RoHS

Electrical Power Specifications

AC Power Supply: 110 to 240VAC 600W (Maximum)

Input Frequency: 50 to 60 Hz

Input Current: 7.5A @ 100V AC, 3.5A @ 240V AC

Inrush Current: <25A max at 240V

Heat Output (BTU/hour): 2355 Max

Power Consumption

IB-40x5-BASE-AC: 283W

IB-40x5-1GE-AC: 291W

IB-40x5-10GE-AC: 308W

IB-40x5-BASE-DC: 251W

IB-40x5-1GE-DC:311W

IB-40x5-10GE-DC: 337W

ND-4005 and TR-4005-BASE-AC: 310W

ND-4005 and TR-4005-1GE-AC: 335W

ND-4005 and TR-4005-10GE-AC: 356W

ND-4005-BASE-DC: 308W

ND-4005-1GE-DC: 316W

ND-4005-10GE-DC: 335W

Fan FRU (Field-Replaceable Unit) SKU (Stock Keeping Unit)

The Infoblox 4005 Series appliances ship with inbuilt fans that can be replaced. The following table lists the fans supported on an Infoblox 4005

series appliance:

SKU Description

T-PSU600-AC FRU, Trinzic 1405, 2205, and 4005 Series AC Power Supply Unit, 600W

T-PSU600-DC FRU, Trinzic 1405, 2205, and 4005 Series DC Power Supply Unit, 600W

T-2205-FAN FRU, Infoblox 2205 and 4005 Series, Rear Accessible Fan, Spare Accessory

DC Power Cable Color Codes

DC power cables ship with a label describing each lead. The label is located near the pigtail leads. The lists -48V DC powertable below

specifications.

-48V DC Power Connector

Cable Pin Cable Color Description

1 Black Positive Return

2 Red Negative Input Voltage

3 Green/Yellow Safety Ground

Accessing the Infoblox 4005 Series Appliance

The management system is the computer from which you configure and monitor the Infoblox appliance. You access the appliance from the

management system remotely across an Ethernet network or directly through a serial cable. After completing the steps in Cabling the Appliance

, you can open an HTTPS connection to the appliance and access the Infoblox Grid Manager using a supported Web browser. Youto a Network

must install and enable Javascript for the Grid Manager to function properly. Grid Manager supports only SSL version 3 and TLS version 1

connections. Infoblox recommends using the latest release of the supported versions of Internet Explorer, Mozilla Firefox or Google Chrome for

best performance.

Alternatively, start an SSHv2 connection and access the CLI through an SSHv2 client. You can also access the CLI by connecting a serial cable

directly from the console port of a management system to the console port on the appliance, and then using a terminal emulation program.

Infoblox recommends that the management system meet the following requirements to operate an Infoblox appliance.

Hardware Requirements for the Management System

Management System Hardware Requirements

Recommended System:

2 GHz (or higher) CPU with at least 1 GB of RAM available for the Infoblox GUI, and network connectivity to an Infoblox appliance

Monitor Resolution:

Minimum: 1280 x 768

Recommended: 1280 x 1024 or better

CLI Access

Secure Socket Shell (SSH) client that supports SSHv2

Terminal emulation program, such as minicom or Hilgraeve Hyperterminal®

Management System Software Requirements

OS Browser

Microsoft Windows 10® Microsoft Internet Explorer® 11.x*, 10.x*

Mozilla Firefox 39.x, 37.x, 32.x, 31.x, 25.x, 21.x, 16.x, and 10.x

Google Chrome 43, 42, 41, 40, 37.x, 36.x, 30.x, 27.x, 22.x, and 16.x

Microsoft Windows 8.1 and

8.0® Microsoft Internet Explorer® 11.x*, 10.x*

Mozilla Firefox 37.x, 32.x, 31.x, 25.x, 21.x, 16.x, and 10.x

Google Chrome 41, 40, 37.x, 36.x, 30.x, 27.x, 22.x, and 16.x

Microsoft Windows 7® Microsoft Internet Explorer® 11.x*, 10.x*, 9.x, and 8.x

Mozilla Firefox 32.x, 31.x, 25.x, 21.x, 16.x, and 10.x