Leonton GINJ-0201-AT-24 Series User manual

LEONTON
GINJ-0201-AT-24 Series
(GINJ-0201-AT-24 / GINJ-0201-AT-24-T)
User Manual

© Copyright 2018 LEONTON Technologies, Co. Ltd.
All Rights Reserved
This document contains information, which is protected by copyright. Reproduction, adaptation or
translation without prior permission is prohibited, except as allowed under the copyright laws.
Disclaimer
LEONTON Technologies, Co. Ltd. provides this manual without warranty of any kind, expressed or
implied, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose. LEONTON Technologies, Co. Ltd. may make improvements and/or changes to
the product and/or specifications of the product described in this manual, without prior notice.
LEONTON Technologies, Co. Ltd. will not be liable for any technical inaccuracies or typographical
errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to
change without prior notice.

FCC Notice
This equipment has been tested and found to comply with the limits for a Class-A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio communications if the
equipment is not installed and used in accordance with the instructions. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
This document is the current official release manual. Please check our website (www.leonton.com)
for any updated manual or contact us by e-mail ([email protected]).

Contents
Overview......................................................................................................................1
Hardware Features................................................................................................1
Package Contents..................................................................................................2
Hardware Description ..................................................................................................1
Physical Dimensions..............................................................................................1
Front Panel............................................................................................................2
Top View................................................................................................................2
LED Indicators........................................................................................................3
Cabling ..................................................................................................................3
Wiring the Power Inputs........................................................................................3
Grounding Note.....................................................................................................4
Mounting Installation...................................................................................................5
DIN-Rail Mounting.................................................................................................5
Wall Mounting.......................................................................................................7
Hardware Installation...................................................................................................9
Installation Steps...................................................................................................9
Maintenance and Service...........................................................................................10
Trouble Shooting........................................................................................................11

1
Overview
PoE and Non-PoE are both highly utilized in the industrial networking applications nowadays;
however, it sometimes goes to an awkward situation that end-device, e.g. remote camera, supports
PoE function but the Ethernet switch does not. Is there any other solution but replacing the switch
with a PoE one?
GINJ-0201-AT-24 Series, launched by Leonton, solve the problem simply by deploying data and
power from non-PoE switch and power input to the PD device. PoE injector is a brilliant low-cost
solution for the case that only one side of devices is supporting PoE function. Therefore, Leonton’s
GINJ-0201-AT-24 Series will be your best choice to deal with the lack of PoE function cases.
GINJ-0201-AT-24 Series supports low voltage 24VDC model with power booster technology,
ensuring full 30W PoE output, for better usage in the automation industry. GINJ-0201-AT-24 Series
with fan less design, besides extending surely apply to various industrial application,
GINJ-0201-AT-24 Series works perfectly in polarized temperature from -40~75℃, and undoubtedly
becomes your best option in the industrial market.
Hardware Features
Interface & Performance
Embedded 1*10/100/1000Tx (PSE 30W) and 1*10/100/1000Tx copper port
Compliant IEEE802.3af/at PoE technologies
Support auto detection and classification for PoE application
Support short-circuit and current-overloading protection for PoE application
The total length from the device A through the Injector to the device B must not exceed 100
meters
Power Input
GINJ-0201-AT-24 Series
■Redundant power DC 12~55V with connective 1*4-pin removable terminal block
■Max. current 2.7A (Included PoE power budget)
■Max. PoE output: 30W
Certification
CE/FCC
Operating Temperature
Standard operating temperature model: -10°C ~ 65°C
Extended operating temperature model (–T): -40°C ~ 75°C

2
Case/Installation
IP-30 protection
Installation in a Pollution Degree 2 industrial environment
DIN-Rail and wall mount design
Package Contents
1 - GINJ-0201-AT-24(-T) product
2 - Wall mounting brackets and screws
1 –Quick Installation Guide (printed)

1
Hardware Description
Physical Dimensions
Figure 2.1, below, shows the physical dimensions of GINJ-0201-AT-24 series.
(W x D x H) is 26mm x 75mm x 95mm
Figure 2.1: GINJ-0201-AT-24 Series Physical Dimensions

2
Front Panel
The front panel of the GINJ-0201-AT-24 series industrial Gigabit PoE Injector is shown below in
Figure 2.2.
Figure 2.2: The Front Panel of GINJ-0201-AT-24 Series
Top View
Figure 2.3, below, shows the top panel of the GINJ-0201-AT-24 series injector that is equipped
with one 4-pin removal terminal block connector for dual 12-55VDC power inputs.
Figure 2.3: Top Panel View of GINJ-0201-AT-24 Series

3
LED Indicators
There are LED light indicators located on the front panel of the industrial PoE Injector that
display the power and PoE status. Each LED indicator has a different color and has its own
specific meaning, see below in Table 2.4.
LED
Color
Description
PWR
Green
On
Power input 1 or 2 is active
Off
Power input 1 and 2 is inactive
PoE
Green
On
The port is supplying power to the
powered-device
Off
No powered-device attached or power
supplying fails
Table 2.4: LED Indictors for GINJ-0201-AT-24 Series
Caution: "PWR" is the abbreviation for "Power".
Cabling
Use the four twisted-pair, category 5e, or the above cabling for RJ-45 port connections. The total
length from the device A through the INJECTOR to the device B must not exceed 100 meters.
Wiring the Power Inputs
Caution: Please follow the below steps to insert the power wire.
Step 1 Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-)
contacts on the terminal block connector as shown below in Figure 2.5.
Figure 2.5: Power Terminal Block

4
Step 2 Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in
Figure 2.6.
Figure 2.6: Power Terminal Block
Caution: Only use copper conductors, 60/75°C, tighten to 5 in-lbs.
The wire gauge for the terminal block should range between 18~20 AWG.
Grounding Note
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the ground screw to the grounding surface prior to
connecting devices. The grounding screw symbol is shown blow in Figure 2.7.
Figure 2.7: Grounding screw
Caution: Using a shielded cable achieves better electromagnetic compatibility.

5
Mounting Installation
DIN-Rail Mounting
The DIN-Rail is pre-installed on the industrial PoE Injector from the factory. If the DIN-Rail is not
on the industrial PoE Injector, please see Figure 3.1 to learn how to install the DIN-Rail on the
injector.
Figure 3.1: The Rear Side of the Injector and DIN-Rail Bracket
Follow the steps below to learn how to hang the industrial PoE Injector.
Step 1 Use the screws to install the DIN-Rail bracket on the rear side of the industrial PoE
Injector.
Caution: The torque for tightening the screws on the device is 3.5 in-lbs.
Step 2 To remove the DIN-Rail bracket, do the opposite from Step 1.
Step 3 After the DIN-Rail bracket is installed on the rear side of the injector, insert the top of
the DIN-Rail on to the track as shown below in Figure 3.2.

6
Figure 3.2: Insert the Injector on the DIN-Rail
Step 4 Lightly pull down the bracket on to the rail as shown below in Figure 3.3.
Figure 3.3: Stable the Injector on DIN-Rail
Step 5 Check if the bracket is mounted tightly on the rail.
Step 6 To remove the industrial PoE Injector from the rail, do the opposite from the above
steps.

7
Wall Mounting
Follow the steps below to mount the industrial PoE Injector using the wall mounting bracket as
shown below in Figure 3.4.
Caution: “Wall” means industrial control panel wall.
Step 1 Remove the DIN-Rail bracket from the industrial PoE Injector by loosening the screws.
Step 2 Place the wall mounting brackets on the top and bottom of the industrial PoE
Injector.
Step 3 Use the screws to screw the wall mounting bracket on the industrial PoE Injector.
Step 4 Use the hook holes at the corners of the wall mounting bracket to hang the industrial
PoE Injector on the wall.
Step 5 To remove the wall mount bracket, do the opposite from the steps above.
Figure 3.4: Remove DIN-Rail Bracket from the Injector

8
Below, in Figure 3.5 are the dimensions of the wall mounting bracket.
Figure 3.5: Wall Mounting Bracket Dimensions

9
Hardware Installation
Installation Steps
This section will explain how to install GINJ-0201-AT-24 series.
Caution: This device is intended for use indoor and at altitudes up to 2000 meters.
Caution: The device is intended to be installed in an industrial control enclosure and panel
Installation Steps
Step 1 Unpack the industrial PoE Injector from the original packing box.
Step 2 Check if the DIN-Rail bracket is screwed on the industrial PoE Injector.
If the DIN-Rail is not screwed on the industrial PoE Injector, please refer to the
DIN-Rail Mounting section for DIN-Rail installation.
If you want to wall mount the industrial PoE Injector, please refer to the Wall
Mounting section for wall mounting installation.
Step 3 To hang the industrial PoE Injector on a DIN-Rail or wall, please refer to the Mounting
Installation section.
Step 4 Power on the industrial PoE Injector and then the power LED light will turn on.
If you need help on how to wire power, please refer to the Wiring the Power Inputs
section.
Please refer to the LED Indicators section for LED light indication.
Step 5 Prepare the twisted-pair, straight-through category 5 cable for Ethernet connection.

10
Maintenance and Service
If the device requires servicing of any kind, the user is required to disconnect and remove it
from its mounting. The initial installation should be done in a way that makes this as
convenient as possible.
Voltage/Power lines should be properly insulated as well as other cables. Be careful when
handling them so as to not trip over.
Do not under any circumstance insert foreign objects of any kind into the heat dissipation
holes located in the different faces of the device. This may not only harm the internal layout,
but might cause harm to user as well.
Do not under any circumstance open the device for any reason. Please contact your dealer for
any repair needed or follow the instructions within the manual.
Clean the device with dry soft cloth.

11
Trouble Shooting
Verify you have the right power cord or adapter. Never use a power supply or adapter with a
non-compliant DC output voltage or it will burn the equipment.
Select the proper UTP or STP cable in order to construct the network. Use an unshielded
twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 5e
for 10M/100M/1000Mbps. Also be sure that the length of any twisted-pair connection does
not exceed 100 meters (328 feet).
NOTE: The total length from the device A through the Injector to the device B must not exceed
100 meters
Diagnosing LED Indicators: To assist in identifying problems, the injector can be easily
monitored with the LED indicators which help to identity if any problems exist.
Please refer to the LED Indicators section for LED light indication.
If the power indicator LED does not turn on when the power cord is plugged in, the user may
have a problem with the power cord. Check for loose power connections, power losses or
surges at the power outlet.
Please contact LEONTON for technical support service, if the problem still cannot be
resolved.