InFocus IN5302 User manual

Regulatory models: F5300
5300
010-0652-00
IN5302, IN5304 User’s Guide

1
Declaration of Conformity
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville,
Oregon 97070 USA
We declare under our sole responsibility that this projector conforms to the
following directives and norms:
EMC Directive 2004/108/EC
EuP Directive 2005/32/EC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1:2005, MOD
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Apple, Macintosh, and PowerBook are trademarks or registered trademarks
of Apple Computer, Inc. IBM is a trademark or registered trademark of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows
are trademarks or registered trademarks of Microsoft Corporation. Adobe
and Acrobat are trademarks or registered trademarks of Adobe Systems
Incorporated. DLP® and the DLP logo are registered trademarks of Texas
Instruments and BrilliantColor™ is a trademark of Texas Instruments.
InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks
or trademarks of InFocus Corporation in the United States and other
countries.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation
may void authority to operate the equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Agency Approvals
UL, cUL
Other specific Country Approvals may apply. Please see product
certification label.
This document applies to regulatory model M5300.
Input ratings: AC 100-240V, 4.8-1.7A,50-60Hz
InFocus reserves the right to alter product offerings and specifications at
any time without notice.

2
Table of Contents
Introduction 5
Positioning the projector 7
Ceiling Mount 8
Cable management 9
Connecting power 10
Connecting a computer source 10
Optional computer connections 11
Displaying an image 12
Adjusting the image 13
Connecting a video device 14
Video device connections 14
Shutting down the projector 16
Troubleshooting your setup 16
Using the remote control 24
Using the audio 25
Using the keypad buttons 26
Optimizing computer images 26
Presentation features 26
Optimizing video images 27
Customizing the projector 27
Dynamic Messaging 27
Using the menus 28
Basic Picture menu 29
Advanced Picture menu 30
Setup menu 31
Status and Service menu 34
Help 34
Using Network Functions 35
Using LitePort 40
Maintenance 43
Cleaning the lens 43
Replacing the projection lamp 44
Using the security lock 45
Appendix 46
SplitScreen Compatibility 47
RS232 Commands 47
Index 54

3
Important Operating Considerations for Safety
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Place the projector in a horizontal position no greater than 8 degrees off
axis.
• Locate the projector at least 4' (1.2m) away from any heating or cooling
vents.
• Do not block ventilation openings. Locate the projector in a well-
ventilated area without obstructions to intake or exhaust vents. Do not
place the projector on a tablecloth or other soft covering that may block
the vents.
• Do not place the projector in direct sunlight, humid, greasy or dusty
places or in places where the projector may come into contact with
smoke or steam.
• Do not look directly into the lens while the projector is being used.
• Do not drop the projector.
• Do not spill liquid on the projector. Spilled liquid may damage the
projector.
• Use the power cord provided. Connect the power cord to a receptacle
with a protective safety (earth) ground terminal. A surge-protected
power strip is recommended.
• Do not overload wall outlets.
• When disconnecting the power cord, hold the plug, not the cord.
• Wash hands after handling the cables supplied with this product.
• The projector remote control uses batteries. Make sure the batteries’
polarity (+/-) is aligned correctly. Dispose of used batteries in
accordance with local disposal laws.
• Use an InFocus approved ceiling mount kit for proper fitting,
ventilation and installation. The warranty does not cover any damage
caused by use of non-approved ceiling mount kits or by installing in an
improper location.
• When the projector is ceiling mounted, wear protective eyewear to
prevent eye injury before opening lamp door.
• The projector must be installed by a qualified professional in order to
ensure proper operation and reduce the risk of hazards or injury. It is
not recommended you install the projector yourself.
• Refer all service to qualified service personnel. Servicing your own
projector can be dangerous to you and will void the warranty.
• Only use replacement parts specified by InFocus. Unauthorized
substitutions may result in fire, electrical shock, or injury, and may
void the warranty
• Only genuine InFocus lamps are tested for use in this projector. Use of
non InFocus lamps may cause electrical shock and fire, and may void
the projector warranty.
•Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
• The projector uses a high-pressure mercury glass lamp. The lamp may
fail prematurely, or it may rupture with a popping sound if jolted,
scratched, or handled while hot. The risk of lamp failure or rupture
also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
• In the unlikely event of a lamp rupture, particles may exit through the
projector vents. Keep people, food, and drinks out of the "keep out"
area under and around the projector, as indicated by the "X" areas
below.
2’ / 0.6 m
3’ / 1 m
5’/1.5m
8’/2.4m

4
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty Booklet

5
Introduction
Your new digital projector is simple to connect, easy to use, and
straightforward to maintain. It is a versatile projector that is flexible enough
for business presentations and home video viewing, too. The IN5302 has
native XGA 1024x768 resolution, and the IN5304 has WXGA 1280x800
resolution. This guide applies to both products. They are compatible with a
wide variety of computers and video devices.
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our support website at www.infocus.com/support, as specifications are
subject to change.
Online registration
Register your projector on our website at www.infocus.com/register to
activate your warranty and receive product updates, announcements, and
registration incentives.
Included Items
Optional Accessories
Optional accessories include optional top covers in a variety of finishes, the
Commander-2 remote, ceiling mount, DisplayLink Extender, DisplayLink
Wireless Adapter, and LiteShow II. These items and other accessories can be
found on our website at www.infocus.com or at your local dealer.
Projector
Remote Control
Power Cord
VGA Computer cable
Documentation USB cable
LiteTouch keypad
Lens Remote control
receiver (IR)
Top front cover
Top rear cover
Lamp access
panel
Connector panel
Power cord
connector

6
Connector panel
The projector provides both computer and video connection options,
including:
•VGAcomputer(2)
•HDMI(2)
•S-video
•Compositevideo
• Component video
• BNC RGBHV and YPbPr for RGBHV, EDTV and HDTV
• Separate audio inputs for video and computer
• USB DisplayLink connector, for computer audio/video input. This
USB connection also provides power out for the DisplayLink Wireless
Adapter.
The projector also provides the following connectors:
• Monitor out, to provide an image on your desktop computer as well as
on the projection screen.
• LAN port for network control and web server.
• LitePort, for connecting a USB flash drive containing JPEG images.
• Audio out, to provide sound for external speakers.
• 5 volt DC output
• 12V screen trigger output
• Wired remote jack (for use with optional Commander 2 remote)
•IRrepeaterjack
• RS-232 connector for serial control. Command control codes are in the
Appendix and on our support website at www.infocus.com/support.
NOTE: Only VGA video is sent to the Monitor out connector.
5 volt DC output
The coaxial 6.4mm x 2.2mm jack provides a constant 5 volt, 2 amp DC
output when the projector is on, and will also provide power when the
projector is in standby (powered off) if Network and DisplayLink items in
the Always-On Functions submenu are set to Yes. It is designed to provide
power to an InFocus LiteShow II wireless device or InFocus DisplayLink
Extender device.
12V Screen Trigger output
The 3.5mm mini-jack screen trigger provides a 12 volt, 0.25 amp DC output.
It turns on when the lamp is lighted. If you connect your projection screen
to this output using the cable that came with your screen, the screen will
move down when the lamp is turned on and the screen will return to its
storage position, when the lamp is turned off.
screen trigger
12V DC
250 mA
wireless
ready
audio 5
video 5 video 4
video 3
remote
computer 4
computer 2 computer 3
L
R
VH
B G R YPbPr
RR
LL
audio 4 audio 3
audio 2
audio 1
LitePort computer 1
DisplayLink
audio out
IR
serial
monitor out
LAN
+5V DC; 2A
DisplayLinkTM
certified
Audio in
Security lock RS-232
Screen
Trigger/5V
Audio out /
IR repeater
Composite
video
RGBHV
YPbPr
HDMI
Monitor out
Component
video
LAN/ Liteport
Cable cover
S-video
DisplayLink
connector
VGA
Wired
remote

7
Positioning the projector
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9’ (1.5m) from the projection screen.
• Position the projector within 10’ (3m) of your power source and within
6’ (1.8m) of your video device (unless you purchase extension cables).
To ensure adequate cable access, do not place the projector within 6”
(.15m) of a wall or other object.
• Position the projector to the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting,
and the video format determine the size of the projected image.
• If the image is square but not centered on the screen or viewing area,
adjust it by using the lens shift dials. Use the Horizontal dial to shift the
lens left or right. Use the Vertical dial to shift the lens up or down.
NOTE: As the lens is shifted away from the lens centerline, the horizon-
tal shift range is reduced. To adjust lens shift efficiently we suggest you
follow these steps:
1Use vertical lens shift to move the image closer to the lens centerline
than the final vertical position.
2Use horizontal lens shift to determine the center horizontal position,
then move image to the center horizontal position.
3Use vertical lens shift to move the image away from the lens centerline
to the final vertical position.
4Use horizontal lens shift to move the image to the final horizontal posi-
tion.
5If lens shift is unable to move the image far enough, move the projector
(preferable) or tilt the projector and then use vertical and horizontal key-
stone to re-position the image.
• The vertical image offset range is 105%~130% for the IN5302 and
105%~125% for the IN5304 (default for both is 105%). The default
horizontal image offset is +/-15%, however at maximum vertical image
offset, there is no horizontal lens shift.
5%
25%
25%
100% (H)
100% (H)
Screen Height
Distance (L)
Screen
Maximum Shift
5%
20%
20%
100% (H)
100% (H)
Screen Height
Distance (L)
Screen
Maximum Shift
(IN5304)
(IN5302)
Horizontal Image Offset +/-15%

8
Ceiling Mount
If you wish to install the projector on the ceiling:
• The projector must be installed by a qualified professional in order to
ensure proper operation and reduce the risk of hazards or injury. It is
not recommended you install the projector yourself.
• We strongly recommend using InFocus approved ceiling mounts for
proper fitting, ventilation and installation. Refer to the installation
guide that comes with the InFocus Ceiling Mount Kit (p/n SP-CEIL-
INSTALL) for more information. The warranty does not cover any
damage caused by use of non-approved ceiling mount kits or by
installing in an improper location.
• The ceiling must be strong enough to support the projector and the
installation must be in accordance with any local building codes. Con-
sult your dealer for more information.
• Maximum supported physical pitch is +/-8º.
• Maximum supported physical horizontal roll is +/-8º.
• Keep all adjacent surfaces 3” (76mm) from sides, front and rear and
.87” (22mm) from the bottom of projector to preserve required airflow
around the projector.
Table 1: IN5302 (XGA)
Range of distance to the screen for a given screen size
Diagonal Screen
Size (inches/m)
Distance to screen
Minimum distance
(feet/m)
Maximum Distance
(feet/m)
60/1.524 6.43/1.96 10.63/3.24
80/2.032 8.63/2.63 14.21/4.33
90/2.286 9.71/2.96 16.01/4.88
150/3.810 16.34/4.98 26.77/8.16
Table 2: IN5304 (WXGA)
Range of distance to the screen for a given screen size
Diagonal Screen
Size (inches/m)
Distance to screen
Minimum distance
(feet/m)
Maximum Distance
(feet/m)
60/1.524 6.66/2.03 10.20/3.11
80/2.032 8.92/2.72 13.71/4.18
90/2.286 10.07/3.07 15.45/4.71
150/3.810 16.93/5.16 25.85/7.88
screentrigger
12VDC
250mA
wireless
ready
audio5
video5 video4
video3
remote
computer4
computer2 computer3
L
R
VHB G R YPbPr
RR
LL
audio4 audio3
audio2
audio1
LitePort computer1
DisplayLink
audioout
IR
serial
monitorout LAN
+5VDC; 2A
DisplayLink
TM
certified
8º

9
Cable management
The integrated cable management system allows you to keep the cables
organized. To use the cable management system, thread the cables into the
slots as shown in the illustration.
cable management system
Using the cable management
system provides you with a
clean, professional-looking
installation.