Infosight Labelase 1000exhaust User manual

LabeLase1000Exhaust Tag Printer

Operation Manual

Revision A2

April 2017

INFOSIGHT CORPORATION

20700 U.S. Highway 23

P.O. Box 5000

Chillicothe, Ohio 45601 USA

+1.740.642.3600 Tel. (M-F 8am-5pm US Eastern Time Zone)

+1-800.401.0716 Emergency Service U.S. & Canada (outside normal business hours)

+1.740.642.4666 Emergency Service International (outside normal business hours)

+1.740.642-5001 Fax.

www.infosight.com

This page intentionally left blank.

First Printing: August 2003

INFOSIGHT CORPORATION reserves the right to make changes in specifications and other information

contained in this manual without prior notice, and the reader should consult INFOSIGHT CORPORATION

to determine whether any such changes have been made.

In no event shall INFOSIGHT CORPORATION be liable for any incidental, indirect, special, or

consequential damages whatsoever (including but not limited to lost profits) arising out of, or relating to

this manual or the information contained in it, even if INFOSIGHT CORPORATION has been advised,

knew, or should have known of the possibility of such damages.

INFOSIGHT CORPORATION expressly warrants the equipment manufactured by it as set forth in the

Standard Terms and Conditions of Sale. INFOSIGHT CORPORATION makes no other warranties, either

expressed or implied (including without limitation warranties as to merchant ability or fitness for a

particular purpose).

InfoTag, LabeLase, PermaLabel®, Pic-Anneal®, and Kettle Tag®Plus are registered trademarks of

InfoSight Corporation.

LabeLaseProducer, Info-TintTM, Foam TagTM, Tough TagTM, AlumaTagTM, and X-Tag™ are

trademarks of InfoSight Corporation.

Windowsis a registered trademark of Microsoft Corporation.

Optical/Laser Safety

INVISIBLE LASER RADIATION

AVOID EYE OR SKIN EXPOSURE TO

DIRECT OR SCATTERED RADIATION

CLASS 1 LASER PRODUCT, USING

A CLASS 4 EMBEDDED LASER (10 W, 10.57 –10.63 μm)

The laser beam Exits the Final lens 5 inches from the tag

Never attempt to operate the Laser Tag Marker without the protective covers in place.

Never attempt to override any of the safety interlocks on the tag printer.

Never attempt to dismantle or repair the tag printer. In case of malfunction contact an Infosight service

representative.

Any of the actions mentioned above may result in permanent eye or skin damage. Refer to Laser Safety

((page 30) for more information on laser safety.

Labels / Warnings

Caution, Laser Radiation –See Appendix A

Warning label located on the front and top of the main cover:

CLASS 4 INVISIBLE LASER

RADIATION WHEN OPEN

AVOID EYE OR SKIN EXPOSURE TO

DIRECT OR SCATTERED RADIATION

Warning label located above the rating plate on the back of the Laser

Marker:

CLASS 1 LASER PRODUCT

Environmental

Conditions

The LabeLase®Printer is intended for Indoor use only. Altitude up to 6500

feet, operating temperature 40 to 100 degrees F, 80% maximum relative

humidity, rated 100-240Vac 50/60 HZ, 5 Amps, pollution degree 2

CAUTION

If this printer is not used in the manner specified by this manual, the

safety features provided may be insufficient.

Warning Label located on the front of the printer, near the tag feed,

regarding California Proposition 65.

FUME EXTRACTION SAFETY INFORMATION

The printer includes a port for attaching the appropriate hoses. It also includes the capability to

automatically start the fume extractor. Customers are able to operate any fume extractor with this

printer. InfoSight recommends the purchase of a filter system (Part # 100-LF) from Filtronics for

this purpose.

SOFTWARE/FIRMWARE LICENSE AGREEMENT

IMPORTANT: THE SUBJECT PROGRAMS ARE LICENSED BY INFOSIGHT CORPORATION TO

END-USERS FOR THEIR USE ONLY ON THE TERMS BELOW. ACCEPTING AND USING THESE

PROGRAMS INDICATES YOUR ACCEPTANCE OF THESE TERMS. THIS IS A LEGAL

AGREEMENT BETWEEN YOU, THE END USER, AND INFOSIGHT CORPORATION.

1) GRANT OF LICENSE. INFOSIGHT CORPORATION ("INFOSIGHT") agrees to grant to you a non-

exclusive license to use the INFOSIGHT software/firmware program (the "PROGRAM") subject to the

terms and conditions of this license agreement.

2) DEFINITION OF TERMS. The term SOFTWARE refers to a computer program stored on CDROM,

floppy diskette, hard disk, magnetic tape, paper tape or other media that must be loaded into the computer's

memory to be executed. The term FIRMWARE refers to a computer program stored in semiconductor

memory (ROM, PROM, EPROM, EEPROM, NVRAM, etc.) that is an integral part of the computer's

memory. Together, these forms of computer programs are referred to as the "PROGRAM".

3) COPYRIGHT. The PROGRAM(s) and Documentation are owned by INFOSIGHT and are protected

by United States copyright laws and international treaty provisions. The PROGRAM(s) contain trade

secrets and proprietary property of INFOSIGHT. You may make one copy of the PROGRAM(s) solely for

backup or archival purposes provided that the copy clearly displays the INFOSIGHT copyright notice.

Additional copies may be made when authorized to do so in writing by INFOSIGHT. In addition to any

other right of INFOSIGHT, INFOSIGHT has the right to terminate this license if the terms of this license

are violated.

4) RESTRICTION ON USE AND TRANSFER. The single-processor version(s) of the PROGRAM(s)

and Documentation are to be used on one computer or embedded system at any one time. The multi-

processor version(s) of the PROGRAM(s) and Documentation may be used over a network provided that

the number of computers accessing the network simultaneously shall not exceed the number authorized by

INFOSIGHT or for which you paid the corresponding multi-processor fee. You may not distribute the

PROGRAM(s) or Documentation to a third party. You may transfer the license and complete package

(retaining nothing) if the transferee agrees to the terms of this License Agreement. Neither the

PROGRAM(s) nor the Documentation may be changed or translated without express written permission of

INFOSIGHT. You may not reverse engineer, decompile or disassemble the PROGRAM(s).

5) WARRANTY for the subject PROGRAM(s) is covered under the INFOSIGHT STANDARD

TERMS AND CONDITIONS OF SALE.

6) TERM. The license is effective until terminated. It may be terminated if you fail to comply with any

term or condition of this License Agreement. You may terminate this License Agreement at any time. In

the event of termination, you agree to destroy the PROGRAM(s) and Documentation together with all

copies and related material.

7) YOUR USE OF THIS PROGRAM(S) acknowledges that you have read this License Agreement and

agree to its terms. This agreement is complete and supersedes any other agreement that may have related to

the subject matter of this agreement.

PREFACE

The LABELASE1000Exhaust Tag Printer is fourth in the family of InfoSight laser tag markers. The

LABELASE1000Exhaust series contains many new features, including: a higher internal processor clock

speed, a PC-driven interface and the ability to print multilingual fonts.

This OPERATIONS manual is intended as a companion to the ONLINE REFERENCE MANUALS

supplied with the Producer & Designer software package and also available on the Infosight webpage:

http://www.infosight.com/labelaseproducer2/producer

http://www.infosight.com/labelaseproducer2/designer

This OPERATIONS AND MAINTENANCE manual will be automatically installed on your computer hard

drive when installing the Producer™ software. It may be found under the PROGRAMS menu with other

INFOSIGHT software and HELP files.

MINIMUM SYSTEM REQUIREMENTS

IBM PC 100% compatible computer.

Windows 7 (32/64bit) / Windows 8/8.1 (32/64 bit) / Windows 10 (32/64 bit)

1 Serial Com port, USB port, or Ethernet port (for connection to the printer).

Color monitor (1024X768 resolution or higher recommended).

TABLE OF CONTENTS

PRINTER SETUP_________________________________________________________ 1

SOFTWARE INSTALLATION________________________________________________ 1

SYSTEM CONNECTIONS & POWER-UP: ______________________________________ 2

PRINTER COMMUNICATIONS______________________________________________ 2

STARTUP SEQUENCE: ____________________________________________________ 3

LOADING NEW TAGS ____________________________________________________ 4

PREPARING TO PRINT TAGS –USING VACUUM FUME EXTRACTOR _______________ 5

PRINTING A TAG ________________________________________________________ 7

LABELASE



PRODUCER



SOFTWARE_______________________________________ 7

PRINTER CONFIGURATION & LASER SETTINGS ________________________________ 9

CYCLE TIME CONSIDERATIONS_____________________________________________ 9

BASIC TROUBLE SHOOTING ______________________________________________ 11

NORMAL MAINTENANCE & SERVICING_____________________________________ 12

AIR FILTER REMOVAL & REPLACEMENT ____________________________________ 12

FUSE REPLACEMENT____________________________________________________ 13

CUSTOMER SERVICE ____________________________________________________ 15

FUNCTIONAL BLOCK DIAGRAM ___________________________________________ 16

Declaration of Conformity _______________________________________________ 17

Appendix A | Laser Safety _______________________________________________ 19

ENGINEERING DRAWINGS _______________________________________________ 23

This page intentionally left blank.

PRINTER SETUP

The LABELASE1000Exhaust Tag Printer requires 100-240 VAC, 50/60 Hz, 2.4 A.

NOTE: both sides of the incoming line voltage are fused. See the Maintenance section for

instructions on replacing fuses.

The LABELASE® 1000Exhaust Tag Printer should be positioned so that the power supply cord exits from

the back of the machine.

The LABELASE1000Exhaust Tag Printer should be placed in a temperature controlled environment.

This marker, though designed for industrial use, should be treated as any typical computer system and

printer. Dirty environments will necessitate a more frequent cleaning schedule for internal optics.

NOTE: If the printer is housed in a secondary protective enclosure, the two exhaust fans located on the

bottom of the printer directly underneath the tag feed drive area must not be obstructed. Ideally the fans

should be exhausted to the environment outside the enclosure, with clean & dry makeup air entering the

enclosure toward the back of the printer near the foam element air filter.

An RS-232 serial communications cable is provided for communicating with your Windows-based PC. A

USB cable is also provided with the USB/Ethernet communications module. See the serial connector

wiring diagram at the back of this manual for additional information if another serial cable is required.

The LabeLase 1000Exhaust Tag Printer should be positioned near the chosen fume extractor. The hoses

should be properly attached. An outlet exists on the back of the machine intended to power the fume

extractor. The outlet for the fume extractor is rated at 3 amps. Plug the fume extractor power cord into this

outlet.

SOFTWARE INSTALLATION

Before connecting the printer to your PC, LabeLase® Producer™ software should first be installed on your

PC.

The easiest way to install the software is to use the Installer Thumb Drive that came with your new printer.

In addition to installing the correct version of Producer™ and Designer for your specific printer model, it

will also allow you to configure the appropriate communications interface.

If your original Installer Thumb Drive is not available OR for the latest release of Producer™ and Designer

software, downloaded the installer package directly from http://www.infosight.com/support/software/37-

labelase-producer-metal-tag-production-software. This is a self-contained, single self-installing file.

However, it will not automatically guide you through the configuration process for communications, and

you must therefore follow the steps outlined in the LabeLase® Producer™Software Installation Manual.

The LabeLase®Producer™Software Installation Manual is available and shipped with your equipment.

The Installation Manual covers printer connection, communication connections, and installation of the

software. Refer to this manual for any issues during software installation on your PC.

NOTE: LabeLase® Producer™ and Designer Software are separate executable programs, however they are

bundled together and downloaded/installed together.

NOTE: rear panel layouts may vary,

depending on the printer

configuration

USB & Ethernet connectors.

Refer to the LabeLase® Producer™

Software Installation Manual for

instructions on installing required

drivers.

SYSTEM CONNECTIONS & POWER-UP:

1.Attach the included RS-232 cable from the LABELASE

1000Exhaust Tag Printer to your Windows-based PC

running LabeLaseProducersoftware.

2.Insert the AC power cord of the fume extractor into the

provided outlet.

3.Connect the AC power cord to the printer and plug the

other end into a nearby power receptacle. NOTE: both

sides of the incoming line voltage are fused. See the

Maintenance section for instructions on replacing

fuses.

4.Place the security key into rear of machine. The key

functions as an ON-OFF switch.

5.Turn key to the vertical (ON) position. NOTE: The

security key can only be removed when in the OFF

position.

6.Press the power switch to the ON position (1).

PRINTER COMMUNICATIONS

LL1000Exhaust series of printers requires a communication link to a PC running Producer™ software. In

addition to the standard serial RS232 link, an integrated USB/Ethernet module is provided. The LabeLase®

Producer™Software Installation Manual addresses Printer Communications in Sections “Connection

Type”, “RS232 Serial COM Port”, “USB Port”, and “Ethernet Network Connection”.

4/5

STARTUP SEQUENCE:

1. Install tag stock onto tag payoff reel. Be sure to re-attach the keeper bar to prevent the tag roll from

falling off the reel.

2. Confirm that the rear power switch is ON and the rear key switch is in the vertical ON position.

3. Remove E-STOP by twisting the red button on the top of the printer by one-quarter turn clockwise.

4. Feed tag stock into printer. If necessary, press the tag FEED button to align tags to the breakoff

location.

5. Start LabeLaseProducersoftware on your PC.

6. Load a pre-existing tag layout, or design a new tag layout. NOTE: designing or changing a tag layout

requires SUPERVISOR login and using LabeLase® Designer Software.

A. Refer to the LabeLase®Producer™Software Manual for loading a tag layout.

B. Refer to the LabeLase®Producer™Software Manual and Designer Software Manual for

changing and/or designing a tag layout.

7. Adjust printer setup parameters if necessary (e.g., laser speed). NOTE: other than setting laser speed

(LIGHTER/DARKER slider bar), this feature requires SUPERVISOR login.

NOTE: The Producersoftware is password protected for all features beyond loading an

existing tag layout, entering tag variable data, adjusting laser speed and initiating printing.

The default password for new installations is blank (no data, no spaces). A new password

should be created before printer is commissioned for regular operator use.

LOADING NEW TAGS

Loading a new roll of tags is as easy as mounting the new roll on the payoff reel so that it unwinds from the

bottom, and hand-feeding the leading edge of the tag stock into the rear feed slot. The marking side of the

tag stock should be facing UP. Gently push it into the slot until it stops against the internal (rear drive)

roller. The printer will then automatically draw the tag stock into the printer.

If necessary, tag stock can be manually fed into the printer by pressing the FEED button located beside the

large red E-STOP button.

CAUTION: DO NOT GRIP THE TAG STOCK BY ITS EDGES WHEN FEEDING

INTO THE PRINTER. PROTECT YOUR HANDS AND FINGERS FROM THE

SHARP EDGES OF THIN METAL TAG STOCK AT ALL TIMES.

Feed Button Operation:

Press & Release Quickly = feed one tag-length OUT (forward).

Press & Hold for 1 Second = feed one tag-length IN (reverse).

Press & Hold for longer than 2 Seconds = CONTINUOUS REVERSE FEED.

Reminder - The marker is not ready for use and will not feed tags until the E-STOP

button is returned to the OUT position by twisting the red button one-quarter turn

CLOCKWISE.

Tag Reel

Keeper Bar

PREPARING TO PRINT TAGS –USING VACUUM FUME EXTRACTOR

LabeLase Producer Software is capable of automatically operating the Vacuum Fume Extractor. The

power supply (maximum 3 amps) to the Vacuum Fume Extractor chosen by the customer should be

connected in the rear of the machine. LabeLase Producer Software is then able to supply power to the

Vacuum Fume Extractor.

The LabeLase Producer Software will turn on the Vacuum Fume Extractor and run it for 10 seconds prior

to printing a tag. This is called the Filter Delay. The LabeLase Producer Software will also automatically

reverse feed tag material to properly align metal tags for their start print location and the break-off point.

This is called Auto Reverse Feed.

Printer Configuration for Metal Tags without Fume Extractor

1. In the LabeLase Producer Software Screen, select Setup/Printer Configuration:

2. Select the Printer Configuration Tab.

3. Check the box next to Disable Filter Delay.

4. The Auto Reverse Feed should be enabled.

5. Print tags according to directions below: PRINTING A METAL TAG.

Printer Configuration for Metal Tags with Fume Extractor

1. In the LabeLase Producer Software Screen, select Setup/Printer Configuration:

2. Select the Printer Configuration Tab.

3. Uncheck the box next to Disable Filter Delay (thus enabling the Filter Delay).

4. The Auto Reverse Feed should be enabled.

5. Print tags according to directions below: PRINTING A METAL TAG.

LabeLase Producer Screens for Printer Configuration:

Please note these screens may change with different versions of LabeLase Producer Software.

1. Setup/Printer Configuration:

2. Select Printer Configuration Tab and check or uncheck desired boxes:

Select Printer Configuration

Don’t Reverse from Tear-Off Before

Print (Or Disable Auto Reverse Feed):

Check Box when printing Flexible Film

Tags

Disable Filter Delay:

Check box when printing

Metal Tags

PRINTING A TAG

Note - The following assumes the LABELASE1000Exhaust Tag Printer has already been setup with a tag

layout.

There are several ways to print a tag using the LABELASE1000Exhaust.

A) If tag stock is loaded in the machine from the rear payoff reel and properly aligned at the break off

exit point:

1. Pressing the PRINT button located beside the red E-STOP will initiate printing of 1 or

more tags, depending on operator-entered data on the main Producer™screen.

2. Pressing the F12 key on your PC.

3. Placing the mouse pointer over the Begin Print button on your PC and left clicking.

4. A print command may be sent from your host computer to your PC via Extended

Protocol.

B) If there is no tag stock feeding in from the back of the machine, a single tag inserted in the

FRONT slot will be automatically drawn into the printer.

5. If the AUTO PRINT SINGLE ITEMS box is checked (enabled) in the SETUP /

PRINTER CONFIGURATION menu (requires supervisor login), then tag printing will

begin automatically with no further action or input required.

6. If the auto print box is NOT checked, then any of the above methods in paragraph (A)

may be used to initiate printing.

NOTE: The SINGLE PRINT feature of the printer requires a minimum tag or tag-strip

length of three inches (76mm).

For example, a single 3x3 (or 3x4, 3x6, etc.) tag may be printed. If single printing of a

1x3 (25 x 76mm) tag is desired, a strip of at least 3 tags must be inserted in the front slot.

CAUTION: DO NOT GRIP THE TAG STOCK BY ITS EDGES WHEN FEEDING

INTO THE PRINTER. PROTECT YOUR HANDS AND FINGERS FROM THE

SHARP EDGES OF THIN METAL TAG STOCK AT ALL TIMES.

LABELASEPRODUCERSOFTWARE

LabeLaseProduceris an integrated, Windows-based application for complete control of tag design and

printing. For complete details, please refer to the ONLINE REFERENCE MANUAL supplied with the

software, or on the web at http://www.infosight.com/labelaseproducer2/producer.

Features:

The software has many features designed to provide maximum flexibility to serve the customer’s specific

marking needs. Some of these features include:

Built-in and online (web access) HELP.

Total freedom to change tag layout whenever needed.

WYSIWYG (“What You See Is What You Get”) user interface for simple and intuitive tag design.

New features emulating popular presentation software packages to speed layout and organization

of complex designs containing multiple text and graphics fields.

An unlimited number of data, text, barcode and graphics fields.

Move fields easily with drag-and-drop.

Rotate fields in 90-degree increments.

Unlimited UNDO-REDO to easily correct mistakes.

Optional placement grid with snap-to placement aid.

Optional field anchor display shows field alignment.

Zoom in/out for detailed display.

Tag geometry features such as holes, slots, bare edges and bend lines can be shown.

Prints all PC-installed fonts, including Unicode characters for all languages.

User-selectable download of message data from a host computer via RS-232, network TCP/IP, or

network file transfer. A wide selection of communications protocols includes InfoSight

Extended, emulation of Zebra and Intermec standard printers, and simple comma or tab-separated,

flat-file formats.

Operator entry of message data, for example if the host computer is unavailable.

Easy control over printer setup parameters such as laser speed and high/low pixel density (i.e.,

“draft” and “normal” printing modes)

Auto-print feature for single tag printing (i.e., whenever a roll of tags is not loaded, a single tag

can be auto-printed simply by inserting the tag in the front tag slot).

Auto-incrementing of all text and number fields, for unattended batch printing.

Option to make text and graphic fields “non-printable”

Option to make non-printable fields visible in the File Open dialog, and on the Producer™ main

screen.

PRINTER CONFIGURATION & LASER SETTINGS

The LabeLase®1000Exhaust printer and LabeLase®Producer™ software are designed with a high degree

of flexibility and user-control, to enable the system to be used in a wide range of applications and on an

ever-increasing array of laser-markable materials.

Calibration and configuration settings are accessed in LabeLase®Producer™ under SETUP-PRINTER

CONFIGURATION. On-line help instructions will guide you through each of the available settings. The

most common parameters for fine-tuning the performance of the printer beyond the easy-to-use

LIGHTER/DARKER SLIDER BAR are LASER SPEED, LASER OFF TICKLE, and LASER ON DUTY

CYCLE, all of which are found under the LASER tab. Each of these parameters separately and together

can be adjusted to create the right balance of black/white contrast, fineness of detail and cycle time.

As laser speed is increased printing cycle time will be faster. In general, as laser speed increases, duty

cycle must also be increased to achieve the same relative blackness. Some materials with especially

sensitive surfaces, such as PermaLabel®, will print more consistently at lower duty cycles, and therefore

correspondingly lower laser speeds. Tickle controls the readiness of the laser to fire and helps maintain

consistency of marking across the tag surface. Some tag materials are more sensitive to power variation

than others, but in most cases this parameter can be left at its factory setting.

Typical Range of Settings (DRAFT mode OFF):

Laser Speed: 50-75 ips

Laser Off Tickle: 7-15 µs

Laser On Duty Cycle: 60-95%

Each printer is calibrated in our factory before shipping, and the

results are recorded on two tags as shown at the right. Save

these tags in the event you ever want to return the printer to its

original factory configuration.

Experience has shown the following settings to be a good

starting point for the most common types of tag material. Each

individual application may then be fine-tuned to achieve the

right balance of cycle time, fineness of detail, and black/white

contrast.

Typical Laser Settings (DRAFT mode OFF)

InfoTag®

Hi - Temp

Pic-Anneal®

PermaLabel®

X-Tag™

Laser

Speed

Tickle

Duty

Cycle

95%

Calibration Tag

Factory Settings

CYCLE TIME CONSIDERATIONS

Tag layout and printer configuration can have a significant influence on cycle time. Here are a few

techniques that in many cases can significantly speed printing.

1. Select DRAFT mode. When DRAFT mode is on, stepper and

mirror resolution, laser speed, font sizes, and barcode and

graphic scales are automatically adjusted.

2. Increase laser speed (move slider bar to LIGHTER). It may be

necessary to increase Laser Duty Cycle to maintain black/white

contrast.

3. Use ARIAL BLACK font for text, to create darker easier-

to-read characters. Also try using the BOLD font setting

instead of a larger font size.

4. Design printing to run ACROSS the tag at 90° rotation

(right angles to tag feed) rather than down the tag at 0°

rotation (printing parallel to tag feed is slower).

5. Avoid drawing graphic boxes around text or other

graphics with long vertical (parallel to tag feed) lines.

6. Combine text strings into fewer lines. A single long line

of text is more efficient than several short lines of text (at

90° rotation, parallel to tag feed).

7. Keep graphics/logo X-scale and Y-scale factors equal to

1. If the graphic or logo must be re-sized to fit on the tag,

use an external application such as MS PAINT to change

the dimensions of the image and re-save the BMP file

before importing into Producer™.

Table of contents

Other InfoSight Printer manuals

InfoSight

InfoSight LabeLase 28 Series Assembly instructions

InfoSight

InfoSight LabeLase LL2800 Assembly instructions

InfoSight

InfoSight LabeLase 1000 Vector Manual

InfoSight

InfoSight LabeLase 4000 Manual

Popular Printer manuals by other brands

FujiFilm

FujiFilm 3000 user guide

Canon

Canon i250 Series specification

EC-PACK

EC-PACK EC-JET 1000Pro manual

DEK

DEK 265 horizon Engineering specification

Panasonic

Panasonic Network Printing DP2000/2500 Setup guide

Canon

Canon MG2900 Series Getting started

MIMAKI

MIMAKI JV3 Series Operation manual

ZHUHAI HONOR TECHNOLOGY

ZHUHAI HONOR TECHNOLOGY XPOS-I100 user guide

Macherey-Nagel

Macherey-Nagel NANOCOLOR UV/VIS II user manual

Polaroid

Polaroid MD100I user guide

Epson

Epson L1800 Service manual

Magicard

Magicard Avalon Duo user guide

Canon

Canon imagePROGRAF iPF6400 Basic guide

Epson

Epson Stylus Photo 900 Setup

MIMAKI

MIMAKI JV3-250 SP Operation manual

YAEN

YAEN POS58C1 user manual

DNP

DNP OP-TU80X operating instructions

Epson

Epson R2880 - Stylus Photo Color Inkjet Printer Start here

InfoSight LabeLase 1000Exhaust User manual

Popular Printer manuals by other brands