Ingrid CRS-G User manual

Rev. 2.0 2021/03
CRS-G Manual EN
NOTE
SPECIFICATIONIMPORTANT NOTICE
MAINTENANCE
This product is not guaranteed against natural wear and deterioration from
normal use and aging.
!!! PERIODICALLY CHECK THE TIGHTENINGS. INCORRECT
TIGHTENING MAY CAUSE MALFUNCTIONING OR BREAKAGE
Make sure to read all instruction manuals included with the product.
This manual is intended primarily for use by professional bicycle
mechanics. Users who are not professionally trained for bicycle assembly
should not attempt to install the components
If any part of the information on the manual is unclear to you, do not
proceed with the installation. Instead, contact your place of purchase or a
local bicycle dealer for their assistance.
All manuals can be viewed on our website http://ingrid.bike
MOSCONI s.r.l. raccomanda di seguire le istruzioni fornite per la corretta installazione ed utilizzo; in caso
le istruzioni non vengano seguite, la garanzia decade. I manuali d'uso INGRID si possono trovare online
all'indirizzo ingrid.bike
La garanzia non copre una manutenzione ordinaria o straordinaria mancante, sbagliata o non appropria-
ta, non copre i danni causati da errato montaggio o assemblaggio con componenti non compatibili, non
copre danni dovuti a urti, cadute o incidenti, la normale usura, l'alterazione o la modifica del prodotto ori-
ginale e i danni causati dal trasporto. Se MOSCONI s.r.l., dopo aver controllato il prodotto, ritiene che il
danno è dovuto ad uno dei motivi di cui sopra, la richiesta di garanzia non sarà accettata e l'articolo difet-
toso verrà restituito al ricorrente che sosterrà le eventuali spese di spedizione.
MOSCONI s.r.l. non è responsabile per danni o lesioni causati da un'installazione non corretta o uso non
corretto del prodotto.
Nella misura ammessa dal diritto locale, fatta eccezione per gli obblighi stabiliti specificatamente nella
presente garanzia, in nessun caso MOSCONI s.r.l. o suoi fornitori di terze parti sarà responsabile per dan-
ni diretti, indiretti, speciali, incidentali o consequenziali.
INGRID È UN MARCHIO CEDUTO IN LICENZA TEMPORANEA A MOSCONI s.r.l.
MOSCONI s.r.l. garantisce i suoi prodotti contro difetti di fabbricazione o di materiale per un periodo di
due anni a partire dalla data di acquisto del primo acquirente, comprovata dalla ricevuta fiscale/scontrino
o comprovata dalla fattura in caso di acquisto diretto. Il difetto deve essere comunicato dal primo proprie-
tario al rivenditore in caso di acquisto non diretto o per posta /e-mail a [email protected] in caso di acquisto
diretto. In caso di restituzione, solo dopo la nostra autorizzazione, gli oneri e rischi di trasporto sono a cari-
co del cliente.
INGRID IS A TRADEMARK TEMPORARY LICENSED TO MOSCONI s.r.l.
MOSCONI s.r.l. guarantee its products against materials or manufacturing defects for a period of two
years starting from the date of purchase of the first buyer, proven by the receipt or proven by the invoice in
case of direct purchase. The defect has to be communicated by the first owner to the dealer in case of
non-direct purchase or by mail/e-mail to [email protected] in case of direct purchase.
MOSCONI s.r.l. is not responsible for damages or injury caused by improper installation or wrong usage
of the product.
To the extent allowed by local law, except for the obligations specifically set forth in this warranty state-
ment, in no event shall MOSCONI s.r.l. or its third party suppliers be liable for direct, indirect, special, inci-
dental, or consequential damages.
In case of return, just after our authorization, transport charges and risks are at customer cost.
MOS/INGRID recommends to follow the provided instructions for the correct usage and installation; in
case instructions are not followed, warranty expires. The INGRID user manuals can be found online at in-
grid.bike
Warranty do not cover missed, wrong or bad ordinary or extraordinary maintenance, damages caused by
wrong assembly or with non-compatible components assembly, impacts, falls or accidents, normal con-
sumption, alteration or modification of the original product and damages caused by transport. If
MOSCONI s.r.l., after checking the product, finds that the damage is due to one of the reasons mentioned
above, the warranty request will not be accepted and the defective item is sent back to the plaintiff who
supports the shipping fees.
Limited warranty and disclaimer
MOSCONI s.r.l. | via la Villa 28 zona artigianale Ghilardino 61034 Fossombrone, PU
Limitazione di garanzia ed esonero di responsabilità
SPECIFICATION
Our crankset system is designed following the common BB design-
standard that provides an asimmetry of 2.5mm on drive side for the
correct chain-line. We recommended to use the following bottom FSA
bracket and spacer:
- - BB-EVO7000BSA (68/73 mm)
- BB30 (68/73 mm) - BB-OS6000 + El226 (adapter)
- BB-EVO9500 (ceramic)
- Press Fit 30 (68/73 mm) - BB-PF6000 + El226 (adapter)
- BB-PF8200 (ceramic) + El226 (adapter)
- BB-OS8200 (ceramic) + El226 (adapter)
- Press Fit BB92 (92 mm) - EL237
- Press Fit BB89.5 (89.5 mm) - EL237 + MW114 (spacer)
To use the CRS-G with bottom bracket not included in this list, check
that the k-factor respects the dimensions required for our spindles
To install the bottom bracket refer to the manufacturer’s manuals.
INTENDED USE: TRAIL, ENDURO
Available cranks lenght: 170mm
Chainline: 49,5 mm (with L131 spindle), 52 mm (with L136 spindle)
Material: Al alloy 2024 (Cranks), Al alloy 7075 (Spindle)
Weight: 625g (L131 spindle without chainring)
Q-Factor: 163 mm (with L131 spindle), 168mm (with L136 spindle)

COMPATIBILITY
APPLY MEDIUM STRENGTH THREADLOCKER TO BLUE COLORED SURFACE
APPLY GREASE TO RED COLORED SURFACE
10 TIGHTENING TORQUE
40-45 Nm
10
TIGHTENING TORQUE
40-45 Nm TO TIGHTEN
THE RING NUT USE
THE INGRID TOOL
ING-T-CS
TIGHTENING TORQUE
12-15 Nm
DSNDS
!! AFTER
INSTALLATION
CHECK THIS
DIMENSION !!
Screw the RING to preload
the crankset until it stops.
Make sure there is no play.
Tighten LOOSELY the screw to lock the
preload ring by a T9 Torx screwdriver.
APPLY GREASE TO RED COLORED SURFACE
DO NOT USE
WAVE WASHERS
min 11.5 mm
SPINDLE ASSEMBLY
CRANCKSET AND CHAINRING ASSEMBLY/DISASSEMBLY
!!! DO NOT REMOVE THE RING NUT
TO REMOVE THE CRANKS USE ONLY A
10MM ALLEN KEY.
BEFORE UNSCREWING CLEAN AND
LUBRICATE THE SPACE BETWEEN THE
SCREW AND THE RING NUT
TO DISASSEMBLY
!!! PERIODICALLY CHECK THE TIGHTENINGS.
INCORRECT TIGHTENING MAY CAUSE
MALFUNCTIONING OR BREAKAGE
USE THE SPACERS
TO ADJUST THE
K-FACTOR
AND TO CENTER
THE CRANKSET
Total width of the bottom bracket
including bearing shields and spasers
DSNDS
IF NECESSARY
ADJUST THIS
DIMENSIONS
WITH SPACERS
L131 Splindle
L136 Splindle
K FACTOR
=+ 2.5mm*
Total 91.5mm
Total 96.5mm
=
* Our crankset system is designed following the common BB design-standard
that provides an asimmetry of 2.5mm on drive side for the correct chain-line
CHECK THAT THE K-FACTOR RESPECTS
THE DIMENSIONS REQUIRED FOR OUR SPINDLES