Injectidry Systems DIRECT-IT IN User manual
OWNER’S MANUAL
DIRECT-IT IN
Injectidry Systems, Inc.
Phone: 425-822-3851 Fax: 425-745-8480 Toll Free: 800-257-0797
www.injectidry.com
October 2006
THE DIRECT-IT IN (UAA1)
USAGE
For use with most standard airmovers on the market today. This adapter dries
positively only by moving dry air into trapped spaces.
SERIOUS PERSONAL OR EYE INJURY CAN RESULT FROM FAILURE TO FOLLOW
SERIOUS PHYSICAL INJURY CAN RESULT FROM FAILURE TO
FOLLOW THESE INSTRUCTIONS:
1. Wear protective eyewear such as safety glasses when stretching, fastening or releasing
hooks. 2. Do not stretch cord more than 50%. (Example 12” to max 18”). Cords can be
stretched more than 50%, but could cause failure of cord or hook & result in serious eye or
other injury. 3. Inspect cord before use. Do not use if cord is frayed or hooks are bent or
damaged. 4. Cord acts like a rubber band. Do not stretch cord toward or away from you to
avoid being struck by hooks. Pull to one side and keep your face and body away from re-
bound path.
HOW TO ATTACH THE DIRECT-IT IN (UAA1)
Step 1. Place the Direct-It IN in front of the airmover to be used (as
shown in picture below).
Step 2. Insert the snout of the airmover into the back of the Direct-It
INhousing.
Step 3. While holding the Direct-It IN housing, carefully stretch the
lower bungee cord around the base of the airmover and
fasten the cord hook into the lower eyelet on the Direct-It IN.
Page 1 of 4
READ BEFORE OPERATING or ATTACHING THE ADAPTER
HOW TO ATTACH THE DIRECT-IT IN (UAA1) Continued
Step 4. Repeat Step 3.
Step 5. We recommend placing the Direct-It IN in the center of the
run to be dried. The hosecuffed ends of the supplied hoses may now
be installed on the Direct-It IN.
INSTALLATION OF DIRECT-IT IN
It is recommended that the drying device be set up at the center of the drying run.
Install in a safe manner. Keep aisles clear and always reduce any unnecessary trip
hazards. Set up warnings if trip hazard exists.
The Direct-It IN comes with the following parts:
01 - UAA1 (bungee cords attached)
03 - 1 ¼ inch Hoses (3 sections of 1 1/4 inch x 50 feet hose)
17 - 5/8 Wall Penetrators (WP2) (bagged)
17 - 1-1/4 Hose Cuffs
01 - CB1 Carry Bag
5/8” WALL PENETRATOR *Redesigned*
This part is black in color. It will slide into the end of the 1
1/4” hose or into a 1 1/4” Hose Cuff. The business end of the
Penetrator is 5/8”.
DRILLING HOLES
We HIGHLY RECOMMEND using an adjustable drill stop.
The depth of drill penetration will be based upon the
thickness of material being drilled. The drill should be
stopped from penetrating hidden wall components such as
electrical wires or plumbing pipes.
Page 2 of 4
Stair Drying Wall Drying Cabinet Drying
Page 3 of 4
SUGGESTED HOSE LENGTHS
We ship the hose blank. This allows you the freedom to choose whatever lengths
make the most sense to you. Replacement or extra hose is available. Be cautious
when cutting your hose with sharp instruments for your own safety and that of the
surface you are cutting on.
CONTAMINATION
On any restoration job when moving air, air filtration devices (AFD's) should be
used to control dust, debris and possible mold.
WARRANTY
DIRECT-IT / DIRECT-IT IN - 1 Year
Limitations: This warranty will not extend to Injectidry products showing any accidental damage, alteration, normal wear,
disassembly, lack of proper maintenance, damage from fire or flood, damage from corrosive or other chemicals, improper
voltage use, unauthorized repairs, use of non-genuine parts and materials, misuse, or any other causes beyond the control
of Injectidry. The warranty obligation extends only to the repairs or replacement of parts found to be defective upon the
examination and the decision of Injectidry Systems.
The preceding limitations constitute the entire warranty. No other warranty or responsibility is expressed or implied. The
warranty includes legal rights to the original purchaser, and additional rights may be available, varying state to state. In
addition, Injectidry Systems Repair Department must authorize all incoming products and/or repair work to be completed
by an authorized repair center. Injectidry Systems is not responsible for any repairs or modifications to any of its products,
unless completed by Injectidry Systems or an authorized service center. We are not responsible for subsequent damaged
caused by the user and or its agents.
CUSTOMER SERVICE
Please call one of our customer service representatives for technical support or to order parts. It is
our number one priority to take care of your needs in a fast and courteous fashion.
Incomplete Shipments
All shortages must be reported within five business days.
Be sure to check the number of cartons or packages. Compare this count with the total listed on
Bill of Lading and confirm that all cartons or packages pertaining to this shipment have been re-
ceived .
If quantities do not match, have the delivery driver note shortage. If the missing cartons or pack-
ages do not show up in the next few days, contact the Shipping Department and we can reship on
a new order.
You must file a Freight Claim for shorted packages if the count differs from the Bill of Lading. For
your protection, the carrier which delivers merchandise to your door is responsible for any loss or
damages. Acceptance of the shipment by the carrier company is acknowledgement that the articles
delivered to them were in good condition and properly packaged.
Freight Damage
Orders are shipped Freight on Board (F.O.B.) from our warehouse in Lynnwood, WA. Once the
product has shipped to the customer, it is the customer’s responsibility. We will assist the cus-
tomer in filing for any freight damage claims but these claims must be filed by the recipient.
We suggest that the shipment be inspected carefully upon receipt. If there is visible damage, note
this on the waybill before you sign and you must notify the carrier immediately.
We want to know if there are any freight damages, so please contact our shipping department
right away.
CONTACT US
Our phone number:
425-822-3851
Our fax number:
425-745-8480
Our toll free number in the U.S. and Canada:
800-257-0797
On the Web at: www.injectidry.com
Page 4 of 4
Table of contents
