Innbox G31 User manual

Quick Start
Innbox G31 GPON Home Gateway

2
Contents
Safety Precautions............................................................................................................................... 3
Introduction............................................................................................................................................ 4
Light indicators...................................................................................................................................... 5
Back panel............................................................................................................................................. 6
Powering on Innbox G31 gateway...................................................................................................... 7
Connectingthe PC............................................................................................................................... 8
Connectingthe STB............................................................................................................................. 9
Starting the internet session ............................................................................................................. 10
Web managementinterface.............................................................................................................. 11
Accessing the web management interface................................................................................ 11

3
Safety Precautions
The following requirements should be fulfilled in order to ensure optimal performance of the
device up-to- date technology without any danger of damaging the equipment or the users:
•Please read the installation instructions in the User Manual thoroughly before you
set up the unit.
•Correct handling ensures the safety of the user and the equipment.
•The device is designed for indoor use. The unit should be used in a sheltered
area, within a temperature range from +5 to +40 Celsius.
•Do not expose the unit to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
•Avoid using the device in dusty or damp places and places where there is a risk of
explosion.
•Do not expose the device to humidity (in a bathroom for example).
•When the device is placed close to devices emitting electromagnetic
interferences such as a microwave oven, HiFi equipment, etc., its performance is
degraded. Move the device outside the disturbance range and the modem resumes
its normal operation.
•Do not try to open or repair the unit yourself. The unit is a complicated electronic
device that may be repaired only by authorized and qualified personnel.
•Only use the power adapter that comes with the package. Using a different
voltage rating power adapter may damage this unit.
•Place this unit on a stable surface or mount it on the wall.
•Disconnect the power adapter before moving the unit.
•Do not put the cables where people can fall over them.
•Keep the package out of reach of children.

4
Introduction
This quick start includes a short description and installation instructions for your Innbox G31
home gateway.
Light indicators
Back panel
Front panel
Powering on Innbox G31 series gateway
Connecting the PC
Connecting the STB
Starting the internet session
Web management interface

5
Light indicators
The following figure shows the front panel of your Innbox G31 home gateway.
Front panel light indicators
Power Green
On - The device is powered on and in operation.
Off - The device is powered off or the power supply is defected.
GPON Green
On - GPON connection is established and working properly.
Flashing - GPON connection failed.
Off - The device failed to receive any optical signal or the signal
strength is too low to detect.
LOS Red
On - The device failed to receive any optical signal or the signal
strength is too low to detect.
Flashing - The received power of the signal is low.
Off - The connection is established and working properly.
Internet Green
on green - The connection to the internet is established.
blinking green - Broadband traffic activity is in progress.
off - The internet connection is disabled.
Phone Green
On -External phone line is plugged and the service is ready to be used.
Flashing - Phone service in use
Off - External phone line is not plugged or the service is disabled.
LAN1...LAN2 Green
On - Devices are connected to the home gateway and turned on.
Flashing - Data transfer activity is in progress.
Off - No devices are connected to the home gateway, or the devices a
re
turned off.

6
Back panel
The following figure shows the rear panel of your Innbox G31 series home gateway.
Rear panel connectors
GPON Optical interface for connection to the outside world.
PHONE
Port for connecting analog phone.
LAN2...LAN1
Two Ethernet ports for connecting the data (PC) or video devices (STB).
RESET This button is used to reset the configuration of the home gateway to factory
default values. When you press this button, the light indicators will briefly go off
and then on again and the home gateway will reset. The factory default settings
will only be valid for the time the device is running. If you want to preservefactory
default settings, save the configuration.
POWER
Power plug for connecting to the supplied 12VDC power adapter.
ON/OFF Button for turning the home gateway on or off. The home gateway is turned on
when the button is pressed in.

7
Powering on Innbox G31 gateway
You require:
•The home gateway unit
•The AC power adapter
1. Take the home gateway and remove the protective cap that closes the GPON optical
port.
2. Connect the GPON optical connector to the GPON port on the device.
3. Plug the DC jack of the power adapter to the to the POWER port on the home
gateway, and the other end to your electricity power outlet.
The ON/OFF button (on the side of the unit) is used to turn the home gateway on or off. The
device is turned on when you press this button and it is pressed in.
When you turn the home gateway on, observe the light indicators. It takes about 30 seconds
for the home gateway to boot up - the Internet and GPON lights are on uninterruptedly.

8
Connecting the PC
You require:
•The home gateway unit
•Ethernet RJ-45 UTP cable
1. Plug one end of the Ethernet cable to one of the two ports on the home gateway as
shown in the picture (LAN 1 or/and 2).
Note: The ports can be pre-configured for specific service - data (PC) or video
(TV). You will obtain this information from your service provider, than plug
your device to the designated port accordingly.
2. Plug the other end of the Ethernet cable to the Ethernet port on your PC.
When the home gateway is turned on and your PC connected, observe the corresponding
LAN light indicator. The light is on uninterruptedly or occasionally blinks.

9
Connecting the STB
You require:
•The home gateway unit
•Ethernet RJ-45 UTP cable
•STB unit
1. Plug one end of the Ethernet cable to one of the two ports on the home gateway as
shown in the picture (LAN 1 or/and 2).
2.
3. Plug the other end of the Ethernet cable to the Ethernet port on your STB device.
Note: Your STB device may differ from the sample device in this picture. The
picture shows only how to connect a STB device to your home gateway. For
instructions on how to power-on your STB and how to connect it to your TV
set, please refer to the user documentation that came with your STB device.
Note: The ports can be pre-configured for specific service - data (PC) or video
(TV). You will obtain this information from your service provider, then plug
your device to the designated port accordingly.
When the home gateway is turned on and your STB connected, observe the corresponding
LAN light indicator. The light is on uninterruptedly or occasionally blinks. If you have properly
connected the STB device to your TV set, you can start using the IPTV and video services
immediately.

10
Starting the internet session
Once you have powered on your home gateway and connected the PC to the home
gateway, you are ready to use the internet. The internet connection is established
automatically.
Note: Before you start using the internet, make sure that you have your PC set
up to obtain the IP address automatically. This is done in the Local Area
Connection properties or settings in your operating system.
ž

11
Web management interface
The web management interface enables you to view the home gateway settings that you can
edit and configure. This is a sample page of the web management interface.
Left frame (navigation tree) lists the home gateway functions that you can change. The
function names are hyperlinks. When you click a link, a corresponding configuration page will
be displayed in the right frame.
Right frame (display area) displays a configuration page for the selected function.
Accessing the web management interface
To access the web management interface, you require:
IP address of the home gateway - default address is 192.168.1.1
User authentication information - the default username is user and password user.
Note: The actual login information could differ from the above information – please check the
label on the bottom surface of the device or consult with your service provider.
1. Start an internet browser on your PC.
2. Type in the IP address http://192.168.1.1 and enter your credentials (username and
password).
3. Enjoy the vast configuration options your new Innbox device is offering.