InnoChain HDR 70m HDBaseT Quick start guide

HDR 70m HDBaseTTM Repeater
4K@60hz YUV 4:4:4

Operating Instructions
Thank you for purchasing this product. For optimum performance and safety, please
read these instructions carefully before connecting, operating or adjusting this
product. Please keep this manual for future reference.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this
equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
To prevent fire or shock hazard, do not expose the unit to rain, moisture
or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through any openings
or empty slots in the unit, as you may damage parts inside the unit.
Do not attach the power supply cabling to building surfaces.
Use only the supplied power supply unit (PSU). Do not use the PSU if it
is damaged.
Do not allow anything to rest on the power cabling or allow any weight
to be placed upon it or any person walk on it.
To protect the unit from overheating, do not block any vents or openings
in the unit housing that provide ventilation and allow for sufficient space
for air to circulate around the unit.
2

Operating Instructions
1. INTRODUCTION
The HDBaseT Repeater is an economical and stable device for extending and
cascade your HDBaseT signal, supporting the highest quality of uncompressed high
definition HD Video of 4K2K, uncompressed multi-channels audio up to 8CH,
Bi-directional control systems, allows HDBaseT signals to be transmitted over a
Single CAT5e/6 cable.
2.APPLICATIONS
Household entertainment sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control
Classroom display and control
3. PACKAGE CONTENTS
1Main unit
2Operating instructions
324V1A Four countries DC power supply
41x IR TX unit
51x IR RX unit
61x Phoenix plugs for RS232 cable termination
71x USB AM to Micro 5P 0.8m cable
82x Fixed Hanger
4. SYSTEM REQUIREMENTS
Input HDBaseT Transmitter and Output HDBaseT Receivers with CAT5e/6/7
connection cables and 3x HDMI output display (TV or monitor).
3

Operating Instructions
5. Features
HDMI2.0Bandwidthupto18Gbps, resolution up to 4k @60hz
YUV 4:4:4 (Work with our TX and RX Devices)
Transmit up to 70m under 1080p, 40m under 4k
Support HDR10, 3D
1x HDBT in; 1x HDBT out with 3x looping HDMI out
Bi-directional wide band IR and RS232 Pass through and EDID Setting
Audio rate up to 48Khz, Maximum support 7.1ch & Dolby True HD, DTS-HD
Support cascade upto 4 layers
HDCP2.2/ HDCP1.4 Compliant
Support Micro USB updating
Support EDID management
6. Specifications
Operating Temperature Range -10 to +55°C (14 to +131 °F)
Operating Humidity Range 5 to 90 % RH (no condensation)
Input Video Signal 0.5-1.0 volts p-p
Input DDC Signal 5 volts p-p (TTL)
Video Format Supported DTV/HDTV:
4K/1080P/1080i/720P/576P/480P/576i/480i
Output Video UHDTV HDMI 2.0 + HDCP 2.2
Output Audio Support 7.1ch DTS-HD, Dolby-HD
Maximum Transmission Distance 70 meters for 1080P, 40 meters for 4K
Power Supply 24V1A
RS232 pass through Baud Rate 115200 bps
Power Consumption 11Watts
Dimensions 245mmL×139mmW×21mmH
Mass (Main unit) 1.06Kg
4

Operating Instructions
7. OPERATION CONTROLSAND FUNCTIONS
7.1 Front Panel:
①IR In: Connect to the supplied IR Receiver cable for IR signal transmission. Place
the IR blaster in direct line-of-sight of the equipment to be controlled.
②IR Out: Connect to the supplied IR Emitter cable for IR signal transmission. Place
the IR blaster in direct line of sight of the equipment to be controlled.
③RS-232: Connect to a PC or laptop with phoenix terminal for the transmission of
RS232 commands.
④FW: USB port to update the firmware.
⑤EDID: Through a 4 PIN DIP switch, the first and second bits are EDID. Two
modes of EDID can be set. Upper means 0; Lower means 1.
ID: Through a 4 PIN DIP Switch, Set the ID number on the 3rd and 4th bits. Upper
means 0, Lower means 1.
⑥RESET: Short press for EDID setting; Long press and plug in power for reset the
product.
⑦HDBT IN; HDMI OUT1; HDMI OUT2; HDMI OUT3; HDBT OUT.
⑧POWER: The LED will illuminate when the device is connected.
5

Operating Instructions
7.2 Rear Panel
①DC/24V: Plug the 24V DC power supply into the unit and connect the adaptor to
an AC outlet
②HDBaseT Out: Connect to the receiver with a single CAT5e/6/7 cable
③HDMI Out1: Connect to a HDMI equipped TV/Monitor
④HDMI Out2: Connect to a HDMI equipped TV/Monitor
⑤HDMI Out3: Connect to a HDMI equipped TV/Monitor
⑥HDBaseT In: Connect to the transmitter with a single CAT5e/6/7 cable
6

Operating Instructions
8. Button instruction:
Short press: Three different EDID modes can be switched, which are Default EDID,
Copy EDID and Priority mode
1). Default EDID mode: 4 different EDID types can be set according to the DIP
switch. After setting, the HDBT IN indicator light will turn off and then return to the
normal state.
DIP Switch EDID
00 4k60-444-2.0 （Default）
01 4K60-444-5.1-HDR
10 4K30-3D-2.0
11 1080P60-3D-2.0
2). Copy EDID mode: HDMI1, HDMI2, HDMI3 and HDBT Out can be copied
according to the DIP switch. After setting, the HDBT IN indicator will slowly flash
for 3 seconds and then return to the normal state
DIP Switch EDID
00 HDBT Out
01 HDMI 1 Out
10 HDMI 2 Out
11 HDMI 3 Out
3). Priority mode: HDMI1 as the highest priority, HDMI2 as a second priority,
HDMI3 to be the lowest level, when two different priority access to TV. EDID will
copy the highest priority, such as: HDMI1 and HDMI2 access any two TV, HDMI1
will be copied. After setting, HDBT IN light fast flash then back to normal after 3
seconds
Long press: Press about 3 seconds to restart the product. All the blue indicators will
flash 3 times, and then TV will re-read the EDID.
Note: After setting the EDID mode, when indicator return to normal, Then restart the
product to get the EDID mode. 7

Operating Instructions
8. IR pass through instruction:
Repeater can only achieve IR dual way pass through with transmitter Devices. It
can’t achieve between Repeater and Repeater.
But it can achieve between Transmitter and Receiver.
9. RS-232 pass through instruction:
ID: Through a 4 PIN DIP Switch, Set the ID number on the 3rd and 4th bits. Upper
means 0, Lower means 1. Then send the command to achieve RS-232 dual way
transmission. The ID number corresponds to the following instruction table:
For example: Repeater’s ID: 00; TX send command to the Repeater,
the command will be: #bypass id1 baud=115200 str=#down.
Then the repeater will get “#down”.
When paired with different devices, the commands are slightly different.
8
Head id% baud=%d str=%s
#bypass
ID number Baud rate Characters
0：all
1: ID 00
2: ID 01
3: ID 10
4: ID 11
115200
57600
38400
19200
14400
9600
4800
2400
Strings that conflict with the
cmd itself are not
supported: %d & %s

Operating Instructions
11. Firmware Update:
①The user should use the CD in color box, read and install CH340 driver and
software in PC;
②Connect unit to PC with usb cable from micro usb port,
click software to select correct usb port:
(Note: if PC is unable to identify the correct usb port, please install the driver
from CD first)
③Type in “A1” in PORT and select PATH with update file then click UPDATAwait
for update till display “Succeed” in red frame:
(Note:please differentiate the firmware before upgrade)
9

Operating Instructions
12. CONNECTION DIAGRAM
①HDBaseT Extender
10

Operating Instructions
②HDBaseT Splitter
11

Operating Instructions
13. MAINTENANCE
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner of benzine to
clean this unit.
14.PRODUCT SERVICE
(1) Damage requiring service:
The unit should be serviced by qualified service personnel if:
(a) The DC power supply cord or AC adaptor has been damaged;
(b) Objects or liquids have gotten into the unit;
(c) The unit has been exposed to rain;
(d) The unit does not operate normally or exhibits a marked change in
performance;The unit has been dropped or the cabinet damaged.
(2) Servicing Personnel: Do not attempt to service the unit beyond that described in
these operating instructions. Refer all other servicing to authorized servicing
personnel.
(3) Replacement parts: When parts need replacing ensure the servicer uses parts
specified by the manufacturer or parts that have the same characteristics as the
original parts. Unauthorized substitutes may result in fire, electric shock, or other
Hazards.
(4) Safety check: After repairs or service, ask the servicer to perform safety checks
to confirm that the unit is in proper working condition.
15.WARRANTY
If your product does not work properly because of a defect in materials or
workmanship, our Company (referred to as "the warrantor" ) will, for the length of
the period indicated as below, (Parts(2)Year, Labor(90) Days) which starts with the
date of original purchase ("Limited Warranty period"), at its option either(a) repair
your product with new or refurbished parts, or (b) replace it with a new of a
refurbished product. The decision to repair or replace will be made by the warrantor.
During the "Labor" Limited Warranty period there will be no charge for labor.
During the "Parts" warranty period, there will be no charge for parts. You must
mail-in your product during the warranty period. This Limited Warranty is extended
only to the original purchaser and only covers product purchased as new. A purchase
receipt or other proof of original purchase date is required for Limited Warranty
service.
12