INSAFE Matrix 3 User manual

INSAFE HELPDESK
0800 52 63 88
[e-mail]
Matrix 3
USER INSTRUCTIONS

Enter each digit slowly and distinctly. The lock signals at each entry.
If a mistake is made press ‘#’ to clear.
Factory-set Master code: 00-12345678 (Change immediately after installation).
This code is for resetting the lock. Please keep it safe.
Factory-set Manager code: 01-123456 (Change immediately after installation).
This code opens the lock and can add or delete a second (02) user if required.
Opening the Lock for the first time
Enter Manager ID and code (01-123456)
the keypad will beep and flash green 3 times. 3 red
flashes indicate wrong code (see “Wrong Try Penalty”)
Turn keypad clockwise 1/4 turn within 3 seconds.
Open safe, turn handle, if any, and open safe door.
Now change your Master and Manager code
0 1 1 2 3 4 5 6
Changing the Master Code
Press #52 to put lock in program mode.
The green led will stay on during this process.
If the light goes out, restart the process
Enter ID (00) plus existing 8-digit code (12345678)
Enter ID (00) and new 8-digit code
Enter ID (00) and new 8-digit code again and press
the purple button to complete the process. The keypad
will beep and flash green 3 times. 3 low beeps and 3 red
LED flashes will indicate code not changed.
# 5 2
0 0
1 2 3 4 5 6 7 8
0 0
X X X X X X X X
0 0
X X X X X X X X
Enter each digit slowly and distinctly. The lock signals at each entry.

Manager / User Code Change
Press #52 to put lock in program mode.
The green led will stay on during this process.
If the light goes out, restart the process
Enter user ID and current combination “01-xxxxxx”
Enter user ID again followed by your new combination
“01-xxxxxx”
Enter ID and new combination again then press
purple button to complete the process. The keypad will
beep and flash green 3 times. 3 low beeps and 3 red LED
flashes will indicate code not changed
Test the code by opening and closing the lock with the
door in the open position.
# 5 2
Remember: Manager and User codes are 8 digits long (a fixed 2-digit ID followed by
a changeable 6-digit PIN).
Ensure door is open through the entire process (including testing).
0 1 X X X X X X
0 1 X X X X X X
0 1 X X X X X X
Adding 02 User Code
CODE MUST BE CHANGED BY THE USER BEFORE THE LOCK CAN BE OPENED.
Press #50 to enter Add User Mode. The green led will
stay on during this process. If the light goes out, restart
the process
Input Manager code (01-xxxxxx)
Input new user ID and code (02-xxxxxx)
Press 2 then 1, followed by the purple button to
complete the process. The keypad will beep and flash
green 3 times. 3 low beeps and 3 red LED flashes will
indicate code not added.
# 5 0
0 1 X X X X X X
0 2 X X X X X X
2 1

In case of difficulty, call the Insafe Helpdesk on 0800 526388
Deleting 02 User Code
Press #56 to enter Delete User Mode
Input Manager code (01-xxxxxx) followed by 02
Press purple button. The keypad will beep and flash
green 3 times. 3 low beeps and 3 red LED flashes will
indicate code not deleted.
# 5 6
0 1 X X X X X X
0 2
Wrong Try Penalty
The entry of four consecutive invalid combinations will start a 5-minute
penalty period. The keypad will not operate during this period.
Changing Batteries
1. Remove battery box located at the bottom of the keypad by pressing the button.
The spring-loaded mechanism will partially eject the battery pack out of the keypad.
2. Remove old batteries and install new 9 vdc ALKALINE only,
e.g. Energizer or Duracell batteries.
3. Reinstall battery pack.
Insafe International Limited
Insafe House Decimus Park Kingstanding Way Tunbridge Wells TN2 3GP
Telephone [phone]
I N S A F E . C O M
S A L E S & S E R VICE • S A L E S @ INS A F E . C O.U K
080 0 52 6 3 8 8