Insignia NS-SP1X7 User manual

Before using your new product, please read these instructions to prevent any damage.
SETTING UP & USING YOUR SMART PLUG
1Connect your mobile device to a WiFi network.
2Download and open the free Insignia Connect app .
3Log in or sign up for an Insignia or Best Buy account.
4Plug the Smart Plug into an outlet. A blinking green
LED means it’s ready for setup.
Note: If LED is not blinking, press and hold down
button for 10 seconds until LED stars blinking green.
5In the app, tap Set Up Device and follow directions.
6Plug a fan, heater, decorative lights, and more into the
plug and control it from the app, or use the Smart
Plug button. You can also use the Smart Plug to set a
schedule for your device.
Final at size: 17 × 4.92 in. (431.8 × 125 mm)
Final fold size: 4.25 x 4.92 in. (101.95 × 125 mm)
QUICK SETUP GUIDE
WiFi Smart Plug
NS-SP1X7
SYSTEM REQUIREMENTS
• Home WiFi network
• Insignia Connect app
• iOS 8.0 or later
• Android Jellybean (5.0) or later
ELECTRICAL RATINGS
• 120V Volts AC, 60Hz
• 15A
• 180 0W
SAFETY INFORMATION
• Plug directly into an electric outlet (not into an extension cord)
• For indoor use only
• Remove the Smart Plug from the outlet before cleaning
• Keep children away from the Smart Plug and the outlet
• Test the device locally for safe operation before attempting to control it
remotely
• DO NOT use with medical or life support equipment.
• DO NOT clean with liquid
• DO NOT remove the ground pin (middle pin)
• DO NOT use in wet or damp areas
• DO NOT exceed the recommended electrical ratings
• DO NOT use in precision timing applications where inaccurate timing
could be dangerous, such as sunlamps or saunas.
• DO NOT use with devices that should not be operated unattended
• DO NOT use with an outlet controlled by a wall switch as the switch may
be turned o
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modications not expressly approved by the grantee of this device could void the user's authority to operate
the equipment.
FCC Caution
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent form that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Compliance
IC Statement
This device complies with Industry Canada’s licence exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your
body.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
1-877-467-4289 (U.S. and Canada) • 01-800-926-3000 (Mexico)
www.insigniaproducts.com
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service
mark of Apple Inc.
Google Play and the Google Play logo are trademarks of Google Inc.
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved.
Made in China
REVIEWERS: with the larger [taller] doc size requested by Andy, we were
able to eliminate two panels. This should save print costs but still
allow sucient space for text in translated version.
REVIEWERS:
please
provide
screenshot of
app

V1 ENGLISH 16-0548
SETTING UP & USING YOUR SMART PLUG
1Connect your mobile device to a WiFi network.
2Download and open the free Insignia Connect app .
3Log in or sign up for an Insignia or Best Buy account.
4Plug the Smart Plug into an outlet. A blinking green
LED means it’s ready for setup.
Note: If LED is not blinking, press and hold down
button for 10 seconds until LED stars blinking green.
5In the app, tap Set Up Device and follow directions.
6Plug a fan, heater, decorative lights, and more into the
plug and control it from the app, or use the Smart
Plug button. You can also use the Smart Plug to set a
schedule for your device.
FEATURES • Press once for manual control
• Press and hold for 10 seconds to reset (LED ashes
green and the Smart Plug resets upon release. Use the
app to recongure network settings.) All previous
settings are erased and the Smart Plug returns to
factory mode.
• Lights up when the Smart Plug is on and electricity is
owing through it
• Blinks once when rmware is successfully installed
• Flashing green: searching for/disconnected from a WiFi
network
• Solid green: connected to a WiFi network and plug is on
• No LED: outlet is o or LED has been disabled from the
app
SAFETY INFORMATION
• Plug directly into an electric outlet (not into an extension cord)
• For indoor use only
• Remove the Smart Plug from the outlet before cleaning
• Keep children away from the Smart Plug and the outlet
• Test the device locally for safe operation before attempting to control it
remotely
• DO NOT use with medical or life support equipment.
• DO NOT clean with liquid
• DO NOT remove the ground pin (middle pin)
• DO NOT use in wet or damp areas
• DO NOT exceed the recommended electrical ratings
• DO NOT use in precision timing applications where inaccurate timing
could be dangerous, such as sunlamps or saunas.
• DO NOT use with devices that should not be operated unattended
• DO NOT use with an outlet controlled by a wall switch as the switch may
be turned o
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modications not expressly approved by the grantee of this device could void the user's authority to operate
the equipment.
FCC Caution
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent form that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Compliance
IC Statement
This device complies with Industry Canada’s licence exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your
body.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
1-877-467-4289 (U.S. and Canada) • 01-800-926-3000 (Mexico)
www.insigniaproducts.com
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service
mark of Apple Inc.
Google Play and the Google Play logo are trademarks of Google Inc.
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved.
Made in China
Power button
Power & WiFi status
indicators
The app
cannot nd
the
SmartPlug.
I can’t nd
the app.
I can’t turn
devices on
or o with
the app.
• Make sure that your mobile device and the SmartPlug are
connected to the same WiFi Network.
• Make sure your network is working properly.
• Reset your SmartPlug. Press and hold for 10 seconds (LED
will ash green and the Smart Plug will reset upon
release).
Get the app from the Apple App store or Google Playstore.
Your device must have iOS 8.0 or later or Android Jellybean
(5.0) or later.
• Make sure the devices you connected to the SmartPlug
are set to the on position.
• Make sure your mobile device and the SmartPlug are
connected to the same WiFi network.
TROUBLESHOOTING
Problem Solution