Inspiration York Fitness 53041 User manual

© 2008 YORK FITNESS
Instruction Manual
*Artist expression, actual product may vary from illustration.
AccomplishMagBike_Manual.indd 1 1/15/09 5:56:41 PM

2 • Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL
READ THIS FIRST
Customer Support
York Fitness U.K. Ltd. (England)
York Way, Daventry, Northants, NN11 4YB, England
Tel: [phone]
Help desk Tel: [phone]
Fax: [phone]
Email: helpdesk@yorktness.co.uk
York Fitness (Australia) pty. ltd.
Unit 1, Lot 2, Swaham Road, Minto, N.S.W. 2566, Australia
Tel: [phone]
Help desk Tel: [phone]
Fax: [phone]
Email: service@yorktness.com.au
Should you require any assistance regarding this product
please gather the following information, and then contact
us using the details above.
S• erial no. - this can be found on the sticker located as
indicated. For future reference, please write down your
serial number in the space below.
O• riginal purchase date.
P• lace of purchase.
I• nformation about the place and conditions of use.
P• recise description of the issue / defect.
Serial No:
Disclaimer
While every eort has been made to ensure that the
information contained in this guide is accurate and
complete, no liability can be accepted for any errors or
omissions. York Fitness reserves the right to change the
specications of the hardware and software described
herein at any time without prior notice.
No part of this guide may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated
into any language in any form, by any means, without the
prior written permission of York Fitness.
York Fitness makes no warranties for damages due to
mistaken operation or malfunction of the equipment.
AccomplishMagBike_Manual.indd 2 1/15/09 5:56:42 PM

Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL • 3
READ THIS FIRST
Safety Precautions
Before using the equipment, please ensure that you read
the safety precautions described below. Always ensure that
the equipment is operated correctly.
The safety precautions noted below are intended to
instruct you in the safe and correct operation of the
equipment to prevent injuries or damage to yourself, other
persons and equipment.
THIS LIST IS NOT EXHAUSTIVE. Save these instructions.
Fitness Precautions:
Before you undertake any programme of exercise that will
increase cardiovascular activity, please be sure to consult
with your doctor. Frequent strenuous exercise should be
approved by your doctor and proper use of your product is
essential.
If you feel any pain or abnormal symptoms, STOP
YOUR WORKOUT IMMEDIATELY. Consult your physician
immediately.
Equipment Safety:
P• lease keep all children away from exercise products
when in use. Do not allow children to climb or play on
them when they are not in use.
R• egularly check to see that all nuts, bolts and ttings
are securely tightened. Periodically checking all
moving parts for obvious signs of wear or damage.
C• lean only with a damp cloth, do not use solvent
cleaners. If you are in any doubt, do not use your
product. Contact CUSTOMER SUPPORT.
B• efore use, always ensure that your product is
positioned on a solid, at surface. If necessary, use a
rubber mat underneath to reduce the possibility of
slippage during use.
U• se this appliance only for its intended use as
described in this manual. Do not use attachments not
recommended by the manufacturer.
Exercise Safety:
W• ear proper workout clothing: Do not wear loose
clothing.
D• o not wear shoes with leather soles or high heels. Tie
all long hair back.
R• emove all personal jewelry before exercising.
A• fter eating, allow 1-2 hours before exercising as this
will help to prevent muscle strain.
I• njuries to health may result from incorrect or excessive
training.
MAX. User Weight: 110KG (250LB)
Your product is intended for use in clean dry
conditions. You should avoid storage in excessively
cold or damp places as this may lead to corrosion and
other related problems that are outside our control.
WARNING
AccomplishMagBike_Manual.indd 3 1/15/09 5:56:42 PM

TABLE OF CONTENTS
Thank you for
purchasing a
YORK FITNESS
equipment.
You have chosen a high quality, safe and innovative piece
of equipment as your training partner and we are certain
it will keep you motivated on the way to achieving your
personal tness goal.
The precautions noted within this guide are intended to
instruct you in the safe and correct use of the products and
to prevent injuries or damage to yourself, other persons and
property. Please read and ensure that you understand them
before proceeding to other sections of this guide.
Table of contents
Read This First .............................................................. 02 - 03
•Disclaimer/Customer Support .................................... 02
•Safety Precautions ........................................................... 03
Table Of Contents ............................................................... 04
Introduction .......................................................................... 05
Assembly Instructions ............................................. 06 - 10
•Getting Started ................................................................. 06
•Hardware Identification Chart .................................... 06
•Assembly Instructions ........................................... 07 - 10
Operational Instructions ........................................ 10 - 11
•Operating Instructions ................................................... 10
•Using The Electronic Meter ........................................... 11
•Batteries Installation ....................................................... 11
Fitness Guide ......................................................................... 12
•Conditioning Guidelines ............................................... 12
Warranty .................................................................................. 13
Part List ............................................................................ 14 - 16
AccomplishMagBike_Manual.indd 4 1/15/09 5:56:45 PM

Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL • 5
HANDLEBAR
HAND PULSE SENSOR
HANDLEBAR SUPPORT
SEAT CUSHION
SEAT POST
MAIN FRAME
RIGHT PEDAL
REAR STABILIZER
FRONT STABILIZER
LEFT PEDAL
COMPUTER
TENSION CONTROL KNOB
INTRODUCTION
Smooth magnetic system•
8 levels of manual resistance•
5 function computer•
Hand pulse sensors•
Adjustable seat height•
AccomplishMagBike_Manual.indd 5 1/15/09 5:56:45 PM

6 • Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL
ASSEMBLY INSTRUCTIONS
Getting Started
Place all parts from the box in a cleared area and position
them on the oor in front of you. Remove all packing
materials from your area and place them back into the box.
Do not dispose of the packing materials until assembly
is completed. Read each step carefully before beginning.
If you are missing a part, please contact our technical
support.
After unpacking the unit, open the hardware bag and make
sure that you have all the following items. Some hardware
may be already attached to the part:
Hardware Identification Chart
This chart is provided to help identity the hardware used
in the assembly process. Place the washers, the end of
the bolts, or screws on the circles to check for the correct
diameter. Use the small scale to check the length of the
bolts and screws.
NOTE: The length of all bolts and screws except those
with at heads is
measured from below
the head to the end of
the bolt or screw. Flat
head bolts and screws
are measured from
the top of the head to
the end of the bolt or
screw.
Part No. 18 x 2
ALLEN HEAD SCREW (M8 X 78MM)
Part No. 65 x 2
ALLEN HEAD SCREW (M8 X 72MM)
Part No. 30 x 7
WASHER (M8 X 1.2MM)
Part No. 62 x 3
M8 WASHER
Part No. 31 x 7
M8 SPRING WASHER
Part No. 35 x 2
M8 CAP NUT
Part No. 20 x 3
ALLEN HEAD SCREW (M8 X 15MM)
Part No. 84 x 2
ALLEN HEAD SCREW (M5 X 12MM)
Part No. 58 x 3
M8 NYLOCK NUT
Part No. 61 x 1
QUICK RELEASE KNOB
Part No. 59 x 1
CLAMP COVER
Part No. 60 x 1
T KNOB
AccomplishMagBike_Manual.indd 6 1/15/09 5:56:46 PM

Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL • 7
STEP 1
Part No. 18 x 2
ALLEN HEAD SCREW (M8 X 78MM)
Part No. 30 x 4
WASHER (M8 X 1.2MM)
Part No. 31 x 2
M8 SPRING WASHER
Part No. 35 x 2
M8 CAP NUT
STEP 2
Part No. 65 x 2
ALLEN HEAD SCREW (M8 X 72MM)
Part No. 30 x 2
WASHER (M8 X 1.2MM)
Part No. 31 x 2
M8 SPRING WASHER
ASSEMBLY INSTRUCTIONS
AccomplishMagBike_Manual.indd 7 1/15/09 5:56:46 PM

8 • Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL
ASSEMBLY INSTRUCTIONS
STEP 3
Part No. 20 x 3
ALLEN HEAD SCREW (M8 X 15MM)
Part No. 31 x 3
M8 SPRING WASHER
Part No. 30 x 3
WASHER (M8 X 1.2MM)
STEP 4
Part No. 58 x 3
M8 NYLOCK NUT
Part No. 62 x 3
M8 WASHER
Part No. 61 x 1
QUICK RELEASE KNOB
AccomplishMagBike_Manual.indd 8 1/15/09 5:56:46 PM

Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL • 9
ASSEMBLY INSTRUCTIONS
STEP 5
Part No. 59 x 1
CLAMP COVER
Part No. 60 x 1
T KNOB
STEP 6
Part No. 84 x 2
SCREW (M5 X 12MM)
AccomplishMagBike_Manual.indd 9 1/15/09 5:56:47 PM

10 • Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL
ASSEMBLY INSTRUCTIONS
STEP 7
Operating Instructions:
A1. djusting the tension control knob:
To increase the load, turn the tension control knob in a clockwise
direction.
To decrease the load, turn the tension control knob in a
counterclockwise direction.
A2. djusting the rear stabilizer end cap:
Turn the rear stabilizer end cap on the rear stabilizer as needed to level
the bike.
A3. djusting the seat post:
Turn the round knob in a counterclockwise direction and then slide the
seat post up or down slightly to the desired hole for the suitable position.
Lock the seat post in place by tightening the round knob in a clockwise
direction.
S4. itting pose:
Sit on the seat cushion when exercising, please tighten the pedaling
straps and hold the handlebar with hands, adjust your posture according
to your exercise speed and intensity.
TENSION KNOB
AccomplishMagBike_Manual.indd 10 1/15/09 5:56:47 PM

Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL • 11
OPERATIONAL INSTRUCTIONS
Using The Electronic Meter
FUNCTION BUTTONS DESCRIPTION
MODE: P1. ress the button to select TIME, DISTANCE and CAL.
P2. ress again to select another workout value.
P3. ress the button and hold for 2 seconds to reset all value to zero (except Odometer).
**When the user replace batteries, all the values will reset to ZERO automatically.
SET: T• o setup the target value of TIME, DISTANCE or CAL, press the button and hold the button
for 2 seconds to speed up the increment.
RESET: Press the button to reset all function values.•
Press the button and hold for 2 seconds to reset all values to zero (except Odometer).•
**When the user replace batteries, all the values will reset to ZERO automatically.
FUNCTIONS DESCRIPTION
AUTO ON/OFF: T• he DISPLAY will show the workout values automatically as the user start to exercise.
The display will turn o automatically after 256 sec of inactivity, but the odometer value
will be held. Once user begins exercise again, the value of the odometer will accumulate
continuously from the previous workout.
AUTO SCAN: P• ress the Mode button to scan through the values of TIME, CAL, ODOMETER, PULSE, SPEED
and DISTANCE. Each value will be displayed for 6 seconds.
SPEED: D• isplay the current training speed from 0 to 99 in KPH or MPH.
DISTANCE: A• ccumulates distances from 0 to 9990. The user may set target distances by pressing SET
and MODE. The values will automatically count down from target set during exercise.
TIME: A• ccumulates total time from 00:00 to 99:59. The user my set target time by pressing SET
and MODE. The values will automatically count down from target set during exercise.
CALORIES: A• ccumulates total calories burnt during training from 0 to 9999 calories. The user may set
target calorie by pressing SET and MODE. The values will automatically count down from
target set during exercise.
**This data is a rough guide which can not be used in medical treatment.
ODOMETER: D• isplays the total accumulated distance from 0 to 999. User can also press MODE to
display the Odometer value.
PULSE: T• he monitor will display the user’s heart rate in beats per minute during training.
RESET: P• ress and hold the button for 2 seconds to reset all values to zero (except Odometer).
Batteries Installation:
Please install 2 AA 1.5V batteries in the battery case on the back of monitor. (Whenever batteries are removed, all the
functions values will be reset to zero.)
I• f the computer displays abnormally, please re-install the battery and try again.
B• attery Spec: 1.5V UM-3 or AA (2PCS).
T• he batteries must be removed from the appliance in order to dispose of the appliance safely.
AccomplishMagBike_Manual.indd 11 1/15/09 5:56:47 PM

12 • Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL
FITNESS GUIDE
Conditioning Guidelines:
How you begin your exercise program depends on your physical condition. If you have been inactive for several years or are
out of shape, start slowly and increase your workout gradually. Increase your workout intensity gradually by monitoring your
heart rate while you exercise.
Remember to follow these essentials:
H• ave your doctor review your training and diet programs.
B• egin your training program slowly with realistic goals that have been set by you and your physician.
W• arm up before you exercise and cool down after you work out.
T• ake your pulse periodically during your workout and strive to stay within a range of 60% (lower intensity) or 90% (higher
intensity) of your maximum heart rate zone. Start at the lower intensity and build up to higher intensity as you become
more aerobically t.
I• f you feel dizzy or light-headed you should slow down or stop exercising.
Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic capacity will
improve over the next six to eight weeks. It is important to pace yourself while you exercise so you don’t tire too quickly.
To determine if you are working out at the correct intensity, use a heart rate monitor or use the table below. For eective
aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of your maximum heart rate. If just
starting an exercising program, work out at the low end of your target heart rate zone. As your aerobic capacity improves,
gradually increase the intensity of your workout by increasing your heart rate.
Measure your heart rate periodically during your workout by stopping the exercise but continuingly to move your legs or walk
around. Place two or three ngers on your wrist and take a six second heartbeat count. Multiply the results by ten to nd your
heart rate. For example, if your six second heartbeat count is 14, your heart rate is 140 beats per minute. A six second count is
used because your heart rate will drop rapidly when you stop exercising. Adjust the intensity of your exercise until your heart
rate is at the proper level.
Target Heart Rate Zone Estimated by Age*
AGE TARGET HEART RATE ZONE
(55% - 90% OF MAXIMUM HEART RATE)
AVERAGE MAXIMUM
HEART RATE 100%
20 YEARS 110-180 BEATS PER MINUTE 200 BEATS PER MINUTE
25 YEARS 107-175 BEATS PER MINUTE 195 BEATS PER MINUTE
30 YEARS 105-171 BEATS PER MINUTE 190 BEATS PER MINUTE
35 YEARS 102-166 BEATS PER MINUTE 185 BEATS PER MINUTE
40 YEARS 99-162 BEATS PER MINUTE 180 BEATS PER MINUTE
45 YEARS 97-157 BEATS PER MINUTE 175 BEATS PER MINUTE
50 YEARS 94-153 BEATS PER MINUTE 170 BEATS PER MINUTE
55 YEARS 91-148 BEATS PER MINUTE 165 BEATS PER MINUTE
60 YEARS 88-144 BEATS PER MINUTE 160 BEATS PER MINUTE
65 YEARS 85-139 BEATS PER MINUTE 155 BEATS PER MINUTE
70 YEARS 83-135 BEATS PER MINUTE 150 BEATS PER MINUTE
*For cardiorespiratory training benets, the American College of Sports Medicine recommends working out within a heart
rate range of 55% to 90% of maximum heart rate. To predict the maximum heart rate, the following formula was used: 220
- Age = predicted maximum heart rate.
AccomplishMagBike_Manual.indd 12 1/15/09 5:56:47 PM

Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL • 13
WARRANTY
This product is supplied with a standard warranty as follows:
1• 2 months frame
1• 2 months other parts
1• 2 months labour
This product is warranted for use in a home, personal, family or household environment
Please Note: Warranty details may vary from one market area to another
Warranty Terms
York Fitness warrants that the Product you have purchased from an authorized York Fitness reseller is free from defects in
materials and workmanship. The Warranty is valid subject to normal and reasonable use in the environment as described
above, and correct assembly of the product during the warranty period. The warranty period extends to the original
purchaser only. It is not transferable to anyone who subsequently purchases the Product from you.
The warranty excludes normal wear and tear on parts.
Your sales receipt, showing the date of purchase of the product, is your proof of the date of purchase.
This warranty becomes valid only if the Product is assembled / installed according to the instructions / directions included
with the product. This warranty does not extend to any product that has been damaged or rendered defective: (a) as a result
of accident, misuse, abuse or lack of reasonable care; (b) by the use of parts not manufactured by York Fitness or sold by York
Fitness; (c) by modication of the product; (d) as a result of service by anyone else other than York Fitness or an authorized
York Fitness warranty service provider.
During the warranty period, York Fitness will at no additional charge provide replacement part(s) or repair the product (at
York Fitness’s option) if it becomes defective, malfunctions or otherwise fails to conform with this warranty under normal,
non-commercial, personal, family or household use. In repairing the product, York Fitness may replace defective parts or at
the option of York Fitness, use serviceable used parts that are equivalent to new parts in performance. All exchanged parts
and products replaced under this warranty will become the property of York Fitness. York Fitness reserves the right to change
manufacturers of any part to cover any existing warranty.
If the product must be returned, you must return the Product or defective part to York Fitness in its original container (or
equivalent) with Proof of Purchase. Any evidence of alteration, erasing or forgery of proof of purchase documents will be
cause to void this warranty. You must prepay any shipping charges and you are responsible for insuring any product or part
that is returned. Should any product submitted for warranty service be found to be ineligible, an estimate of repair cost will
be furnished and the repair will be made if requested, upon York Fitness’s receipt of payment or acceptable arrangement
of payment. Under no circumstances will returns be accepted without return authorization by our Customer Service
department.
To obtain warranty service you must provide the following information:
Name of Product, Product Code, Batch No, Date Purchased, and Nature of fault or part number required.
Neither dealer of this product nor any retail establishment selling this product has any authority to make any warranties or to
promise remedies in addition to, or inconsistent with, those stated above. This warranty does not aect your statutory rights.
Please note that warranty terms may vary from one market area to another.
AccomplishMagBike_Manual.indd 13 1/15/09 5:56:47 PM

14 • Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL
PART LIST
AccomplishMagBike_Manual.indd 14 1/15/09 5:56:47 PM

Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL • 15
PART LIST
AccomplishMagBike_Manual.indd 15 1/15/09 5:56:48 PM

16 • Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL
KEY NO. DESCRIPTION QTY
1BASE FRAME 1
2HANDLEBAR POST 1
3HANDLEBAR 1
4SADDLE POST 1
5SCREW (M5 X 12MM) 2
6MAGNET 1
7FRONT STABILIZER 1
8REAR STABILIZER 1
9MAGNETIC HOLDER 1
10 BRACKET 1
11 BUSH 1
12 CRANK 1
13 BELT WHEEL 1
14 FLY WHEEL 1
15 FLYWHEEL AXLE 1
16 FRONT PULLEY 1
17 BEARING IC1735-FT 1
18 ALLEN HEAD SCREW (M8 X 78MM) 2
19 ALLEN HEAD SCREW (M10 X 35MM) 1
20 ALLEN HEAD SCREW (M8 X 15MM) 4
21 HEX HEAD BOLT (M8 X 52MM) 1
22 HEX HEAD BOLT (M8 X 25MM) 1
23 SCREW #10 X 24 X 5/8 1
24 SCREW (M4 X 16MM) 2
25 SCREW (M5 X 10MM) 1
26 SCREW #10 X 24 X 5/8 4
27 WASHER (M30 X 0.8MM) 1
28 WASHER (M10 X 2.0MM) 1
29 WASHER (M8 X 1.5MM) 1
30 WASHER (M8 X 1.2MM) 10
31 M8 SPRING WASHER 8
32 M10 NYLONT WASHER 2
33 3/8” NUT (T=9MM) 1
34 3/8” NUT (T=3MM) 1
35 M8 CAP NUT 2
36 M10 NUT (T=6MM) 1
37 NYLOCK NUT M8 2
38 3/8”WH NUT 2
39 TOOL - SPANNER 1
40 TOOL - SPANNER 1
41 TOOL - ALLEN KEY 1
42 BEARING <6000ZZ> 1
KEY NO. DESCRIPTION QTY
43 BEARING <6003ZZ> 2
44 BEARING <6300ZZ> 1
45 38MM WASHER 1
46 BALL BEARING RING NUT (R) 1
47 BEARING BOWL 2
48 BALL BEARING RING NUT (L) 1
49 35MM WASHER 1
50 RING NUT 2
51 BALL BEARING 2
52 CLIP C10 1
53 SPRING (SMALL) 1
54 SPRING (BIG) 1
55 WHEEL ASSY 2
56 FRONT FOOT COVER 2
57 REAR FOOT COVER 1
58 M8 NYLOCK NUT 3
59 CLAMP COVER 1
60 T KNOB 1
61 QUICK RELEASE KNOB 1
62 M8 WASHER 3
63 SADDLE SUPPORT TUBE INSERT 1
64 DRIVE BELT WHEEL 1
65 ALLEN HEAD SCREW (M8 X 72MM) 2
66 PEDAL (L/R) 1
67 SEAT 1
68 FOAM GRIP 2
69 END CAP OF HANDLEBAR 2
70 BELT 1
71 CHAIN COVER (L) 1
72 CHAIN COVER (R) 1
73 CRANK COVER 2
74 WASHER CURVE M5 1
75 TENSION CONTROL 1
76 TENSION CONNECTOR 1
77 COMPUTER 1
78 COMPUTER WIRE 1
79 SENSOR WIRE 1
80 HAND PULSE WIRE 1
81 SENSOR BRACKET 1
82 HAND PULSE GRIPS 2
83 REAR FOOT COVER 1
84 SCREW (M5 X 12MM) 2
AccomplishMagBike_Manual.indd 16 1/15/09 5:56:48 PM

Inspiration Accomplish Mag Bike | INSTRUCTION MANUAL • 17
AccomplishMagBike_Manual.indd 17 1/15/09 5:56:48 PM

© 2008 YORK FITNESS
Instruction Manual
*Artist expression, actual product may vary from illustration.
AccomplishMagBike_Manual.indd 18 1/15/09 5:56:48 PM