Intec Controls MSR ELECTRONIC PolyGard AT-1110 User manual

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
November 14, 2014 – Revision
Polygard® is a registered trademark of MSR AT-1110V3


























PolyGard® AT-1110 V3


ElectrochemicalCarbonMonoxideTransmitter
SerialNo.AT03003



June18,2009


Specifications subject to change without notice. | USA 141114 | Page 1of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3
January 04, 2016 – Revision

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 02

 

2.1ControlMode ...................................................................................................................................3
2.2Sensor .............................................................................................................................................3

3.1MountingInstructions.......................................................................................................................4
3.2Installation........................................................................................................................................4

4.1WiringConnection ...........................................................................................................................5

5.1Calibration........................................................................................................................................5
5.2ManualCalibration...........................................................................................................................6
5.2.1Zeropoint.....................................................................................................................................6
5.2.2Gain..............................................................................................................................................6
5.2.3CalculationofControlVoltage......................................................................................................7
5.3OptionRelayOutput ........................................................................................................................8

6.1Inspections.......................................................................................................................................9
6.2Calibration........................................................................................................................................9
6.3ExchangeofSensorElement ..........................................................................................................9

7.1AnalogMode..................................................................................................................................10


 
 
11.1IntendedProductApplication .....................................................................................................17
11.2Installers’Responsibilities ..........................................................................................................17
11.3Maintenance...............................................................................................................................17
11.4LimitedWarranty........................................................................................................................17

Specifications subject to change without notice. | USA 141114 | Page 2of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 2of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 03


 
The PolyGard

CO analog gas transmitter AT1110 utilizes digital processing the measuring values and
temperature compensation for the continuous monitoring of the ambient air to detect the presence of carbon
monoxidegas.Mainapplicationrangesareundergroundcarparks,tunnels,engineteststations,shelters,loading
areasetc.
The intended sites are all areas being directly connected to the public low voltage supply, e.g. residential,
commercialandindustrialrangesaswellassmallenterprises.
The PolyGard
®
 CO analog transmitter must not be used in potentially explosive atmospheres. The AT1110
Transmittermayonlybeusedwithinambientconditionsdescribedinthetechnicaldata.
 
 
Analogmode:
Theanalogoutputcanbeselectedascurrentsignalwith(0)420mAorasvoltagesignal(0)210V.Inthe(0)420
mAmodeandwithoutanysupplementaryoptions,theAT1110alsoworksinthe2wiretechnique.
 
Thesensorportionofthetransmitterisasealedelectrochemicalcellwiththreeelectrodes,sensing,counterand
reference or with two electrodes, sensing and reference. The ambient air to be monitored diffuses through a
membrane filter into the liquid electrolyte of the sensor. The chemical process of the measurement is one of
oxidationwhereonemoleculeofthetargetgasisexchangedforonemoleculeofoxygen.Thereactiondrivesthe
oxygen molecule to the counter electrode, generating a DC microampere signal between the sensing and
referenceelectrodes.Thissignalislineartothevolumeconcentrationofthesensedgas.Thesignalisevaluated
bytheconnectedamplifierandtransformedintoalinearoutputsignal.
Electrochemicalprocessesalwaysleadbyandbytoalossofsensitivity.Thereforeregularcalibrationofzeropoint
andgainisnecessary

Thereisasmallquantityofcorrosiveliquidinthesensorelement.Ifincaseofdamagepersonsorobjectstouch
theliquid,youhavetocleantheaffectedareasasfastandcarefullyaspossiblewithtapwater.Outofusesensors
mustbedisposedinthesamewayasbatteries.

Specifications subject to change without notice. | USA 141114 | Page 3of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 3of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 04

 
 
Avoid any force (e.g. by thumb) on the sensor element during operation or installation. Electronics can be
destroyedbystaticelectricity.Therefore,donottouchtheequipmentwithoutawriststrapconnectedtogroundor
withoutstandingonaconductivefloor.
 
Whenchoosingthemountingsitepleasepayattentiontothefollowing:
• Thespecificweightofcarbonmonoxideisasmallerthanthatofair(factor0.97).
Recommendedmountingheightis1.5m(5feet)to1.8m(6feet)abovefloor.
• Choosemountinglocationofthesensoraccordingtothelocalregulations.
• Considertheventilationconditions!Donotmountthetransmitterinthecenteroftheairflow(airpassages,
suctionholes).
• Mount the transmitter at a location with minimum vibration andminimum variation in temperature (avoid
directsunlight).
• Avoidlocationswherewater,oiletc.mayinfluenceproperoperationandwheremechanicaldamagemight
bepossible.
• Provideadequatespacearoundthesensorformaintenanceandcalibrationwork.
Ductmounting
• Mountonlyinastraightsectionofductwithminimumairvortex.Keepaminimumdistanceof1m(3,5feet)
fromanycurveorobstacle.
• Mountonlyinaductsystemwithamaximumairvelocityof10m/s(2000ft/min)orless.
• Mountingmustbeperformedsothattheprobeopeningsareinlinewiththeairflow.
 
• Openthecover.UnplugbasicPCBcarefullyfromthebottompart.
• Fixbottompartbyscrewsverticallytothewall(terminalblockstotheground).
• PluginthebasicPCBatX4andX5withcare.Replacethecover.
 
Considerstaticelectricity!See3.Mounting
• Installation of the electrical wiring should only be performed by a trained specialist according to the
connection diagram, without any power applied to conductors and according to the corresponding
regulations!
• Avoidanyinfluenceofexternalinterferencebyusingshieldedcablesforthesignalline,butdonotconnect
theshield.
• Recommended cable for analog mode: Belden Twisted Shielded (20 AWG), max. res. 73 /km (20.8
/1000ft).
• ItisimportanttoensurethatthewireshieldsoranybarewiresdonotshortthemountedPCB.
Specifications subject to change without notice. | USA 141114 | Page 4of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 4of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 05

 
• Openthecover.UnplugbasicPCBcarefullyfromterminalblocksatX4andX5.
• Insertthecable,connectcableleadstoterminalblocks.Seefig.1and2.
• ReplugthePCBintheterminalblocksX4,X5.Replacecover.
 
Considercommissioninginstructionsatwhenexchangingofsensorelements.
Onlytrainedtechniciansshouldperformthefollowing:
• Checkmountinglocation.
• Selectoutputsignalform:Currentorvoltage,andstartingpoint0or20%.Seefig.4.
• Checkpowervoltage.
• CheckPCBAT1110forpropermountingatX4andX5.
• CheckthesensorforpropermountingattheconnectorsX3/X7ofthePCBAT1110.
• Calibratethetransmitter(ifnotalreadyfactorycalibrated).
Requiredinstrumentsforcommissioning(calibration)ofthetransmitter:
• TestgasbottlewithsyntheticairofCOfreeambientair.
• TestgasbottlewithCO(ppm)intherangeof30–80%ofthemeasuringrange.
• Gaspressureregulatorwithflowmetertocontrolthegasflowto300ml/min.
• Calibrationadapterwithtube,dependingonthetransmittertype.
• Digitalvoltmeterwithrange0–300mV,accuracy1%andasmallscrewdriver.

Priortocalibrationthesensorelementmustbefullystabilizedbyapplyingpowervoltageforatleast1hourwithout
interruption.
Pleaseobserveproperhandlingproceduresfortestgasbottles!
COcalibrationgasistoxic,neverinhalethegas!
Symptoms:Dizziness,headacheandnausea.
Procedureifexposed:Takethevictimintofreshairatonce,calladoctor.
 
Dependingontheversionandthecontrolmodetherearethreedifferentpossibilitiestocalibratethetransmitter:

Manualcalibrationisonlypossibleifthetransmitterisequippedwiththepushbutton“Zero”andthepotentiometer
“Gain”(=versionformanualcalibration).
Specifications subject to change without notice. | USA 141114 | Page 5of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 5of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 06

 
 
• Connectcalibrationadaptercarefullytothesensorelement.
• Applysyntheticair(300ml/min;1Bar(14.5psi)±10%),orCOfreeambientair.
• Wait2minutesuntilthesignalisstable,pushbutton“Zero”for5seconds.
Aftersuccessfulcalibrationthemeasuringsignaliscorrectedautomatically.Dependingontheselected
signalstartingpointthemeasuringsignalshowsthefollowingvalues:
Signalstartat2Vor4mA   40mV=0ppm
Signalstartat0Vor0mA   0mV=0ppm
Ifthezeropointisoutoftheadmissiblerange(>20mVatstartingpoint0%/>60mVatstartingpoint
(20%)beforecalibration,thereisnocorrectionofthemeasuringsignal.Thesensorhastobereplaced.
• Removecalibrationadaptercarefullybyturninglightly.Checkthesensorforcorrectmounting!
 
• Connectcalibrationadaptercarefullytothesensorelement.
• ApplycalibrationtestgasCO(300ml/min;1Bar(14.5psi)±10%).
• Waittwominutesuntilthesignalisstable,adjustcontrolvoltagewithpotentiometer”Gain”untilthesignal
correspondstothecalculatedvalue±3mV,seecalculationsection5.3.
• Removecalibrationadapterwithacarefullightturn.Checkthesensorforcorrectmounting!
By limiting the gain factor, calibration will not be possible any more when the sensitivity of the sensor
reachesaresidualsensitivityof30%.Thenthesensorhastobereplaced.
Specifications subject to change without notice. | USA 141114 | Page 6of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 6of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 07

 

Controlvoltage(mV)=160(mV)xtestgasconcentrationCO(ppm)+40(mV)
measuringrangeCO(ppm)


Controlvoltage(mV)=200(mV)xtestgasconcentrationCO(ppm)
measuringrangeCO(ppm)


Measuringrange 250ppm
Testgasconcentration 200ppmCO
Controlvoltage:Signalstart2V/4mA 168mV
Controlvoltage:Signalstart0V/0mA 160mV
         
160(mV)x200(ppm)+40(mV)=168mV   200(mV)x200(ppm)=160mV
250(ppm)            250(ppm)



Specifications subject to change without notice. | USA 141114 | Page 7of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 7of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 08

 
The two relays are activated in dependence of the gas concentration. If the gas concentration exceeds the
adjustedalarmthreshold,thecorrespondingrelayswitcheson. Ifthe gasconcentration falls belowthethreshold
minushysteresis,therelayswitchesoffagain.
The contact function for relay 2, NC (normally closed) or NO (normally open), can be selected via the jumper
NO/NC.Seefig1and3.Relay1isequippedwithachangeovercontact.
Via theModBus interface thetwoalarmthresholdsand the hysteresisare freely adjustableat thePC withinthe
measuringrange.Theprocedurecanbereadfromtheusermanual“ModBusSoftware”.
Thefollowingparametersarefactoryset.
Alarmthreshold1=Relay1: 50ppm
Alarmthreshold2=Relay2: 100ppm
Switchinghysteresis:   15ppm


Specifications subject to change without notice. | USA 141114 | Page 8of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 8of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 09

 
 
Inspection, service and calibration of the transmitters should be done by trained technicians and executed at
regular intervals. We therefore recommend concluding a service contract with Intec Wilson Mohr or oneof their
authorizedpartners.
 
(Seesection5.1and5.2)
• Atcommissioningandatperiodicintervalsdeterminedbythepersonresponsibleforthegasdetection
system (recommendation every 12 months).
• Afterexchangeofthesensor
• Ifincaseofoperationalorclimaticinfluencesthesensitivityofthesensorfallsbelow70%inoperation,
calibrationwillnotbepossibleanymore.Thenthesensorhastobechanged.
 
Considerstaticelectricity!Seepoint3.
Sensorshouldalwaysbeinstalledwithoutpowerapplied:
• UnplugbasicPCBAT1110carefullyfromthebottompart.
• UnplugoldsensorfromthePCB.
• Takethenewsensoroutoftheoriginalpacking.
• PluginthesensorelementintothePCBatX3/X7.
• ReplugthePCBAT1110intoterminalblocksX4,X5carefully.
• Calibrateaccordingtosection5.
Specifications subject to change without notice. | USA 141114 | Page 9of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 9of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 10

 
 
  
Jumper020%notset Checkjumperposition
Powervoltagenotapplied
MeasuretensionatX4:
Twowire:Pin1(+)and4()
Threewire:Pin1(+)and2()
PCBAT1110notpluggedincorrectlyat
X4andX5
ReplugPCBcorrectly
Outputsignal<3mA/1.5V
and/orcontrolvoltage<30mV
onlyforstartingsignal2V/4mA

Wirebreak Checkthewiring
Outputsignal>22mA/220mV Shortcircuit Checkthewiring
Sensorelementnotcalibrated Calibratesensorelement
Controlvoltagedoesnotreach
thecalculatedvalue Sensorsensitivity<30% Replacesensorelement
Powervoltagenotapplied MeasuretensionatX4
Noreactionoftheoutputsignal
inspiteofgasconcentration Signal(Pin4)notwiredcorrectly Checkthewiring




 
ThecrosssensitivitydependsontheusedtransmittertypeandcanbereadfromthetableTechnicalData(see9.).
Othergasescanhaveaninfluenceonthesensitivity,too.Thetabledoesnotclaimtobecomplete.Theindicated
sensitivitydataareonlystandardvaluesreferringtonewsensorelements.
Specifications subject to change without notice. | USA 141114 | Page 10 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 10 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 11


 
 
Gastype Carbonmonoxide(CO)
Sensorelement Electrochemical,diffusion
Measuringrange(standard,otherranges
accordingtothedatasheet)
250ppmfactoryset
adjustablebetween0150and0300ppm
Pressurerange Atmosphere±15%
Humidity 15–90%RHnoncondensing
Storagetemperaturerange 5°Cto30°C(23°Fto86°F)
Storagetime Max.6months
Mountingheight 1.5to1.8m(5to6ft.)
Sensorcoverage 5,000sq.ft.,max.10,000sq.ft.
(465m2,max930m2),under"ideal
conditions"
Accuracy ±.5ppmofreading
Repeatability ±1%ofreading
Longtermsensitivityoutputdrift <.4%signalloss/month
Responsetime t90<30sec.
Lifeexpectancy 5yearsplus,normalconditions
Temperaturerange 14°Fto104°F(10°Cto40°C)
Crosssensitivity* Concentration(ppm) Reaction(ppm)
Sulphurdioxide,SO25 0
HydrogenSulphide,H2S 15 1
Nitrogendioxide,NO25 0
Nitricoxide,NO 35 <3.5
HydrogenCyanideHCN 10 0
HydrogenChlorine 5 0
Hydrogen,H2100 <60
ChlorineCL2 1 0
EthyleneC2H4 100 <75
 
Powersupply 1828VDC/AC,reversepolarityprotected
2wiremode:OnlyVDC
Powerconsumption(withoutoptions) 22mA,max.(0.6VA)
 Thetabledoesn’tclaimtobecomplete. Othergases,too,canhaveaninfluenceonthesensitivity.Thementionedcrosssensitivity
dataareonlyreferencevaluesvalidfornewsensors.

Specifications subject to change without notice. | USA 141114 | Page 11 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 11 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 12

Analogoutputsignal
Selectable:Current/tension
Startingpoint0/20%
(0)4–20mA,load≤500,
(0)2–10V;load≥50k
proportional,overloadandshortcircuitproof

Enclosure* Galvanizedsteel
Enclosurecolor* Lightgrey
Dimensions*(HxWxD) 142x142x63mm/(5.59x5.59x2.48in.)
Weight* Approx.0.7lbs(0.3kg)
Protectionclass*NEMA1
Mounting* Wallmounting,pillarmounting
Cableentry Standard1xM20
Wireconnection Screwtypeterminalmin.0.25,to2.5mm2
24to14AWG
Wiredistance Currentsignalca.500m(1500ft.)
Voltagesignalca.200m(500ft.)
EMCDirective89/336/EEC
CE

Two years material and workmanship,
12 months normal exposure for sensor
element

 
Alarmrelay130VAC/DC0.5A,potentialfree,SPDT
Alarmrelay2 30VAC/DC0.5A,potentialfreeSPNO/SPNC
Powerconsumption 30mA,(max.0.8VA)
 
LCD Twolines,16characterseach,notilluminated
Powerconsumption 10mA(max.0.3VA)
 
Temperaturecontrolled 3°C±2°C(37.5°F±35.5°F)
Ambienttemperature 40°C(40°F)
Powersupply 18–28VDC/AC
Powerconsumption 0.5A;12VA
Specifications subject to change without notice. | USA 141114 | Page 12 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 12 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 13




 NEMA3(IP45)
w/probe 7/8in.(22mm)diameterand
7.16in.(182mm)length
Cableentry 1holefor1/2in.conduit
 NEMA4X(IP65),w/splashguard
MaterialABSUL94V0
ColorLightgray
Dimensions(HxWxD)4.80x4.72x3.42in.
(122x120x87mm)
 NEMA12(IP55)
MaterialPolycarbonate,UL94HB,fireretardant
ColorLightgray
Dimensions(HxWxD) 5.12x3.31x2.95in.
(130x84x75mm)
ConformityUL50standards
Cableentry 1holesfor1/2in.conduitforwall(surface)
mountedand1holeonbacksideofbaseplate
forsinglegangelectricalboxmounting
connectionTerminalblocks.


Specifications subject to change without notice. | USA 141114 | Page 13 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 13 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 14

 
Application:Analogmode
Fig.1 








































Specifications subject to change without notice. | USA 141114 | Page 14 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 14 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 15


Fig.3  
AT1110v3






















Terminalblock















Selectionanalogoutputsignal
Fig.4






Jumper020% JumperVA Outputsignal
Notset Notset 0–20mA
Set Notset 4–20mA
Notset Set 0–10V
Set Set 2–10V
5
4
3
2
1
1234567
X5
X4
Specifications subject to change without notice. | USA 141114 | Page 15 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 15 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 16
Type: CONKIT-E/CH-AT
Calibration adapter
Fig. 5
Type: CONKIT-E/CH-AT
Specifications subject to change without notice. | USA 141114 | Page 16 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 16 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Customer Services [phone] & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Fax [phone] & (888) FX INTEC
www.inteccontrols.com
Specication subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard®CO Transmitter
User Manual - AT-1110 V3 Page 17

11 Notes and General Information
It is important to read this user manual thoroughly and clearly in order to understand the information and instructions.
The PolyGard® transmitter must be used within product specication capabilities. The appropriate operating and
maintenance instructions and recommendations must be followed. Due to on-going product development, INTEC
and MSR reserves the right to change specications without notice.
The information contained herein is based upon data considered accurate. However, no guarantee is expressed or
implied regarding the accuracy of this data.
11.1 Intended Product Application
The PolyGard®transmitter is designed and manufactured for control applications and air quality compliance in
commercial buildings and manufacturing plants (i.e. detection and automatic exhaust fan control for automotive
maintenance facilities, enclosed parking garages, engine repair shops, warehouses with forklifts, re stations,
tunnels, etc.).
11.2 Installers’ Responsibilities
It is the installer’s responsibility to ensure that all PolyGard®transmitter is installed in compliance with all national
and local codes and OSHA requirements. Installation should be implemented only by technicians familiar with proper
installation techniques and with codes, standards and proper safety procedures for control installations and the latest
edition of the National Electrical Code (ANSI/NFPA70). It is also essential to follow strictly all instructions as provided
in the user manual.
11.3 Maintenance
It is recommended to check the PolyGard®transmitter regularly. Due to regular maintenance, any performance
deviations may easily be corrected. Re-calibration and part replacement in the eld may be implemented by a
qualied technician and with the appropriate tools. Alternatively, the easily removable plug-in transmitter card with
the sensor may be returned for service to INTEC Controls.
11.4 Limited Warranty
MSR-Electronic-GmbH and INTEC Controls warrants the PolyGard®transmitter for a period of two years, 12 months
normal exposure for the sensor, from the date of shipment against defects in material or workmanship. Should any
evidence of defects in material or workmanship occur during the warranty period, INTEC Controls will repair or
replace the product at their own discretion, without charge.
This warranty does not apply to units that have been altered, had attempted repair, or been subject to abuse,
accidental or otherwise. The warranty also does not apply to units in which the sensor element has been overexposed
or gas poisoned. The above warranty is in lieu of all other express warranties, obligations or liabilities.
This warranty applies only to the PolyGard®transmitter. INTEC Controls or MSR shall not be liable for any incidental
or consequential damages arising out of or related to the use of the PolyGard®transmitter.
If the PolyGard® transmitter needs to be returned to INTEC Controls for service, an RMA number must be obtained
prior to sending.
Specifications subject to change without notice. | USA 141114 | Page 17 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 17 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: [phone] & (888) GO.INTEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard®is a registered trademark of MSR-Electronic GmbH | AT-1110V3