Integratech DIM-BASIC User manual

RF Single Color Remote Controller 09.2839D.04226
Operation
Pair with RF receivers:
Click “RF Code Key”
on RF receiver
Function introduction
Important: Read All Instructions Prior to Installation
Output RF signal
Operation Frequency 868/915/434MHz
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 120x48x17.6mm
Front side
Back side
•Control 1 zone of RF receiver
• Single color controller
• Compatible with universal serie RF receiver
• 1 receiver can be paired by max 8 different remote controls.
• Waterproof grade: IP20
Product Data
Safety & Warnings
Power Supply 4.5V(3xAAA battery)
LED lights connected with the
RF receiver will flicker once
Press and hold down to decrease
light intensity
Click to turn on
The receiver is paired with
the remote successfully.
Turn on
the remote
Touch the
color wheel
How to delete the pairing:
Press and hold down on the receiver for over 3 seconds until connected LED lights flicker twice,
which means the pairing is deleted successfully.
“RF Code Key”
Click to turn off
Brightness wheel, touch to select
brightness
Press and hold down to save color,
click to recall the saved. Each zone
can save 2 colors.
50% brightness
Press and hold down to increase
light intensity
LED indicator
4.5V(3xAAA battery)
100% brightness
25% brightness
75% brightness
If you use multiple receivers, you can have all the receivers in the same zone
Lear ning Ke y
RF LED Rec eiv er
1 Zone RF remote
Lear ning Ke y
RF LED Rec eiv er
•This device contains AAA batteries that shall be stored and disposed properly.
•DO NOT expose the device to moisture.
DIM-BASIC

RF Receiver 09.01029.04296
Input
Voltage Remarks
Output
Current
12-24VDC Constant voltage
3x(60-120)W
3x5A
Output
Power
RF Code Key
RF LED Controller
V+
V-
INPUT
V+
V-
INPUT
V+
1/R/WW
2/G/CW
3/B
RF code key:pair with the RF remote
Waterproof grade: IP20
Radio Frequency : 868/915/434mhz
Function introduction
Important: Read All Instructions Prior to Installation
•DO NOT install with power applied to device.
•DO NOT expose the device to moisture.
DC Power input
Product Data
Safety & Warnings
Do wiring according to connection diagram.
Pair RF Receiver with RF remote:
1. Connect and wire up the RF receiver correctly, power on.
2. Turn on the remote, click the “RF Code Key” button on receiver, immediately click a zone number to pair
the receiver to the specified zone if the remote is a multi-zone controller (if it is a single zone remote, this
step is unnecessary), then touch the color wheel or slider bar on the remote (if the remote does not have
color wheel or slider bar, click or touch any keys), the connected led light on receiver flickers twice, which
means well paired.
Note: one receiver can be paired with max 8 remote controls.
Delete the pairing:
1. Wire up the RF receiver correctly, power on
2. Hold down the “RF Code Key” button on receiver for over 3 seconds until the connected led light on
receiver flickers twice, which means well deleted.
Operation
If you use multiple receivers, you have two choices:
Option 1: have all the receivers in the same zone, like zone 1
Zone 1
Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4
Zone 1 Zone 2 Zone 3
RF remote RF remote
Size(LxWxH)
145x46.5x16mm
Common Anode Output(+)
CH 1:R/WW output(-)
CH 2:G/CW output(-)
CH 3:B output(-)
DC Power input
With single color LED strip
V+ V-
AC Power
50/60Hz
L
N
G
V+
V-
OUTP UT
INPUT
12V/24V
CV PSU
Singl e Color LED Strip
V+ V+
V- V-
RF Co de Key
RF LED Controller
V+
V-
INPUT
V+
V-
INPUT
V+
1/R/WW
2/G/CW
3/B
RF Cod e Key
RF LE D Contr oller
V+
V-
INPU T
V+
V-
INPU T
V+
1/R/ WW
2/G/ CW
3/B
RF Cod e Key
RF LE D Contr oller
V+
V-
INPU T
V+
V-
INPU T
V+
1/R/ WW
2/G/ CW
3/B
RF Cod e Key
RF LE D Contr oller
V+
V-
INPU T
V+
V-
INPU T
V+
1/R/ WW
2/G/ CW
3/B
RF Cod e Key
RF LE D Contr oller
V+
V-
INPU T
V+
V-
INPU T
V+
1/R/ WW
2/G/ CW
3/B
RF Cod e Key
RF LE D Contr oller
V+
V-
INPU T
V+
V-
INPU T
V+
1/R/ WW
2/G/ CW
3/B
DIM-BASIC