Integrated Power Designs REL-110 SERIES User manual

INTEGRATED
POWER DESIGNS
300 Stewart Road
Wilkes-Barre, PA 18706 USA
Phone: [phone]
Web: www.ipdpower.com
Email: [e-mail]
Fax: [phone]
DRAWING NO: 1080018
REVISION: 33
REL-110 SERIES OPERATING INSTRUCTIONS
INPUT RATING: 100-240VAC, 2 A, 50-60 Hz.
OUTPUT RATING: 110 Watts Maximum Total Continuous Output Power with 300 LFM Forced Air.
80 Watts Maximum Total Continuous Output Power Convection Cooled.
65 Watts Maximum Total Continuous Output Power Convection Cooled with Chassis and Cover.
MODEL LISTING:
NOTES: 1. Total current from Outputs 1 and 2 must not exceed 12 Amps with convection cooling.
2. Total current from Outputs 3 and 4 must not exceed 3 Amps with convection cooling.
3. Rated 8 Amps maximum with convection cooling.
4. Rated 16 Amps maximum with convection cooling.
5. A suffix may be added to the model number to indicate the following optional configurations:
(CH-chassis, CO-cover, IO-isolated outputs, TS-terminal strip).
6. Approved to UL/CSA 60950-1 only.
7. Approved to EN 60950-1 only.
Model
Output 1(1)
Output 2(1)
Output 3(2)
Output 4(2)
REL-110-4001
+3.3VDC/10A(3)
+5VDC/6A
+12VDC/2A
-12VDC/2A
REL-110-4002
+5VDC/10A(3)
+3.3VDC/6A
+12VDC/2A
-12VDC/2A
REL-110-4003
+5VDC/10A(3)
+3.3VDC/6A
+15VDC/2A
-15VDC/2A
REL-110-4004
+5VDC/10A(3)
-5VDC/6A
+12VDC/2A
-12VDC/2A
REL-110-4005
+5VDC/10A(3)
-5VDC/6A
+15VDC/2A
-15VDC/2A
REL-110-4006
+5VDC/10A(3)
+24VDC/2A
+12VDC/2A
-12VDC/2A
REL-110-4007
+5VDC/10A(3)
+24VDC/2A
+15VDC/2A
-15VDC/2A
REL-110-4009
+5VDC/10A(3)
+24VDC/2A
+7VDC/2.5A
-7VDC/2.5A
REL-110-4010
9VDC/6A
24VDC/2A
12VDC/2A
12VDC/2A
REL-110-4011
+32VDC/2A
-32VDC/2A
+12VDC/2A
-12VDC/2A
REL-110-4012(6)
+5VDC/10A(3)
-9VDC/3A
+15VDC/2A
-15VDC/2A
REL-110-3001
+5VDC/10A(3)
+12VDC/3A
-----
-12VDC/3A
REL-110-3002
+5VDC/10A(3)
+15VDC/2A
-----
-15VDC/2A
REL-110-3003
+8VDC/5A
-8VDC/1A
-----
+30VDC/1A
REL-110-3004
+9VDC/3A
+24VDC/3A
+13VDC/2A
-----
REL-110-3005
5VDC/12A
9.5VDC/1A
-----
9.5VDC/1A
REL-110-3006(6)
5VDC/7A
15VDC/3.5A
-----
-15VDC/2A
REL-110-3007(7)
20V/2.5A
12V/2.5A
-----
12V/2.5A
REL-110-2001
+3.3VDC/10A(3)
+5VDC/6A
-----
-----
REL-110-2002
+5VDC/10A(3)
+12VDC/5A
-----
-----
REL-110-2003
+5VDC/10A(3)
+24VDC/3A
-----
-----
REL-110-2004
+12VDC/5A
-12VDC/4A
-----
-----
REL-110-2005
+15VDC/4A
-15VDC/3A
-----
-----
REL-110-2006
+18VDC/4A
-18VDC/3A
-----
-----
REL-110-2007(7)
+6V/10A
+7.5V/6A
-----
-----
REL-110-1001
2.5VDC/22A(4)
-----
-----
-----
REL-110-1002
3.3VDC/22A(4)
-----
-----
-----
REL-110-1003
5VDC/22A(4)
-----
-----
-----
REL-110-1004
12VDC/9.2A
-----
-----
-----
REL-110-1005
15VDC/7.3A
-----
-----
-----
REL-110-1006
24VDC/4.6A
-----
-----
-----
REL-110-1007
28VDC/3.9A
-----
-----
-----
REL-110-1008
48VDC/2.3A
-----
-----
-----
DECLARATION OF CONFORMITY
Manufacturer: Integrated Power Designs, Inc.
Manufacturer’s Address: 300 Stewart Road, Wilkes-Barre, PA 18706 USA
Declares all models listed above including all options are in compliance with the following European Community Directives:
Low Voltage Directive 2014/35/EU of 26 February 2014
RoHS Directive 2011/65/EU of 8 June 2011
In addition, all models are Certified to be in compliance with applicable requirements of UL 60950-1:2007, ANSI/AAMI ES60601:2005/(R) 2012, IEC
60950-1/A2:2013 and IEC 60601-1:2005/A1:2012 including all EU national deviations, CAN/CSA-C22.2 No. 60950-1-07, CAN/CSA- C22.2 No. 60601-
1:2014, EN 60950-1:2006/A2:2013 and EN 60601-1:2006/A1:2013.
BY:
Steven Thompson- President
EUROPEAN CONTACT:
CompuMess Elektronik GmbH
Lise-Meitner-Strasse 1
PLACE:
Integrated Power Designs
85716 Unterschleiβheim
300 Stewart Road, Wilkes-Barre, PA 18706 USA
Telephone: [phone]
DATE:
January 3, 2017

INTEGRATED
POWER DESIGNS
300 Stewart Road
Wilkes-Barre, PA 18706 USA
Phone: [phone]
Web: www.ipdpower.com
Email: [e-mail]
Fax: [phone]
DRAWING NO: 1080018
REVISION: 33
REL-110 SERIES OPERATING INSTRUCTIONS
CLASSIFICATION: 1. Protection against electric shock –Class I.
2. Protection against harmful ingress of water –IPXO (Non-protected), ordinary.
3. Methods of sterilization –None.
4. Suitability for use in an oxygen rich environment –End user responsibility, not evaluated.
5. Mode of operation –Continuous.
WARNING! An open internal fuse indicates a catastrophic failure of circuit component(s). Repair must be by authorized IPD personnel only.
RISK OF FIRE! Refer to fuse rating on power supply circuit board for rating.
WARNING! Dangerous voltages are present on some components, printed circuit board traces and heatsinks.
SHOCK HAZARD!
INPUT FUSE: This product includes a single fuse in the phase lead only. In consideration of IEC 60601-1:2005 Clause 8.11.5, a second fuse may
be required in the neutral lead of the end use equipment
SEPERATION: Primary to secondary creepage distance is 8mm minimum, clearance 5mm minimum (2MOPP). Primary to ground creepage
distance is 4mm minimum, clearance 2.5mm minimum (1MOPP). Secondary to ground creepage is 2.3mm minimum, clearance is
1.4mm minimum (Operational Insulation). Required seperation must be maintained in the end use equipment to preserve the
established means of protection.
OUTPUTS: The outputs are not acceptable for patient connection without additional isolation. All outputs are SELV under normal and single
fault conditions unless otherwise indicated.
TEMPERATURES: The maximum operating temperatures of safety components as defined in the applicable safety standards must not be exceeded
after installation in the end use equipment. Output power, ambient air temperature and convection or forced air cooling availability
should be considered in the end use equipment.
HIPOT: In consideration of IEC 60601-1:2005 Clause 8.8.3, care must be taken to insure the voltage applied to a reinforced insulation does
not overstress different types and levels of insulation. Breakdown of basic insulation and catastrophic failure of the power supply
may result if a test voltage of greater than 1800 VAC is applied between primary and secondary circuits. Each isolating component
is factory tested at 4000 VAC minimum prior to installation. Primary and secondary to ground capacitors may need to be
disconnected prior to performing a dielectric strength test on the power supply or the end product.
INSTALLATION: The power supplies included in model listing on reverse side are considered components intended for professional installation into
end use equipment. The protective earth (ground) terminal must be bonded to protective earth in the end use equipment.
EMISSIONS: This product was tested for compliance with EN 55022 and EN 55011 Class B conducted and radiated emissions using the
techniques listed below and non-inductive load resistors to simulate operation in a typical installation. All or a combination of the
following requirements may be necessary to insure compliance in the end use equipment.
1. Installation of the power supply, output cables and loads in a shielded enclosure.
2. Use of optional chassis and cover.
3. Use of shielded I/O cables.
4. Use of ferrite beads on I/O cables.
5. Grounded output returns.
CONNECTIONS /
DIMENSIONS:
AIR FLOW 1. Recommended 2. Good 3. Fair
DIRECTION:
CONNECTORS: P1: AC Input –0.156 inch friction lock header mates with Tyco 640250-3 or equivalent crimp terminal housing with Tyco 3-
640706-1 or equivalent crimp terminal.
P2: DC Output (Single Output) –0.156 inch friction lock header mates with Tyco 770849-8 or equivalent crimp terminal
housing with Tyco 3-640707-1 or equivalent crimp terminal.
P2: DC Output (Multiple Output) –0.156 inch friction lock header mates with Tyco 1-770849-0 or equivalent crimp terminal
housing with Tyco 3-640707-1 or equivalent crimp terminal.
G: Protective Earth (Ground) –0.187 quick disconnect terminal.
P3: Power Fail / Sense (Single and Multiple Output) –0.100 breakaway header mates with Molex 50-57-9002 or equivalent
crimp terminal housing with Molex type 71851 or equivalent crimp terminal.