Intek MT-446A User manual

INSTRUCTION MANUAL
MANUALE DI ISTRUZIONI
PROFESSIONAL 2-WAY RADIO
PC PROGRAMMABLE
PMR 446 / 16CH

Declaration of Conformity
With the present declaration, we certify that the following products :
INTEK MT-446A
comply with all the technical regulations applicable to the above mentioned products
in accordance with the EC Directives 1999/5/EC.
Type of product : PMR 446 UHF Transceiver
Details of applied standards : EN 300 296-1/-2, EN 301 489-1/-5,
EN 60950-1
Manufacturer : INTEK S.R.L.
Via G. Marconi, 16
20090 Segrate, Italy
Tel. [phone] / Fax. [phone]
E-mail : [email protected]
Contact Reference : Armando Zanni
Tel. [phone] / Fax. [phone]
E-mail : [email protected]
Segrate, 06/05/2014 dr. Vittorio Zanetti
(C.E.O.)
DECLARATION OF CONFORMITY
NOTICE !
It is recommended to carefully read this owner’s manual before using the product. This will also help the user to
prevent using the radio in violation of the regulations valid in the country where the product is used, as well as to
avoid any possible interferences with other services.
RoHS
2002/95/EC

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpacking and checking parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Preliminary Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Getting acquainted with the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Advanced functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Frequency/Channels programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Index - Notice
- 1 -
NOTICE !
This transceiver is programmable via PC, using the dedicated software (free download at
www.intek-radios.com) and the PC interface cable (optional item). Any programming or
modification of the original default setting must be made by a specialised technician or by an
authorised service centre. Some functions of this transceiver might be programmed in violation
of the technical rules in force for the use of the PMR-446 band. It is the user’s responsibility to
check that any modification to the programming will be done in compliance with the current
regulations. Any modification to the product, alteration of the internal circuit, of the external
structure of the radio or any programming in violation of the current regulations will
automatically void the product certification and your right to use the product. INTEK S.R.L.
declines any responsibility concerning any modification of the product, made by the user or by
a third party, after delivery of the product.
NOTICE !
This transceiver has been factory programmed, in order to use the product immediately after
purchase. The programming includes the activation of channels/frequencies in the PMR-446
band, according to the technical rules in force for the use of this band. Please refer to the table
at page 12 for details.
English

Thank you !
Thank you for choosing INTEK for your two-way business radios applications. This user friendly
transceiver will provide you with clear and reliable communications and will keep your professional
activities at peak efficiency. This transceiver incorporates the latest and most advanced technology, so
you will be pleased with its quality and its technical features.
Important notice !
The use of PMR-446 transceivers is subject to the regulations applied in the country where the product
has to be used. As regulations are usually subject to possible modifications, please check the current
regulations in your country with your dealer or local supplier. INTEK does not take any responsibility for
illegal use and operation of this product not in accordance with the regulation of the country where the
product is used.
Safety notice
The user must know and understand the common risks related to the use of transceivers. Do not use
the transceiver in environments at risk of explosion (where there are gas, dusts, smokes, etc.). Do not
use the transceiver in service areas or fuel stations, on board aircrafts, etc.
Cautions
Please observe the following precautions, in order to avoid causing fire, personal injuries or damage to
the radio:
It is suggested that each transmitted message lasts a few minutes only, since very long
transmissions at the maximum transmitter RF output power may overheat the transmitter.
Do not alter or modify in any way your transceiver.
Do not expose the transceiver for a long time to direct sunlight and do not place it close to
heat sources.
Do not expose the transceiver to excessively dusty or damp places, do not place it on
unstable surfaces.
In case of anomalous smell or smoke that leaks out from the transceiver, turn it off immediately
and remove the battery pack. Please contact an authorised service center.
Please do not dispose off used battery with common garbage. Please use the dedicated
disposal containers.
- 2 -
General Information
English

Unpacking and Checking Parts - Supplied Accessories
- 3 -
Unpacking and checking parts
Carefully unpack the product. Please identify all the parts listed below, before wasting the packaging. If
any part is missing or if the packaging shows any damage, please contact your dealer immediately.
Supplied accessories
7.4V 1500mAh Li-Ion Rechargeable Battery Pack
Electronic Quick Desk Charger
Belt Clip
Handstrap
User Manual
Electronic Quick Desk Charger Li-Ion Battery Pack
Belt Clip Handstrap User Manual
English

Preliminary Steps
- 4 -
Battery charging
Connect the 230VAC adaptor charger to the desk type battery
charger and to a 230VAC outlet. The Green Led will light to
confirm that the charger is powered. Switch ON the radio and
check (within 5 seconds) the battery level on Battery Level
Indicator (8); 4 bars mean full charge and no lighted bars
mean that battery needs to be immediately recharged.
Insert the empty battery or the transceiver with the battery
pack in the battery charger. Please make sure that the
charging contacts of the radio are connected with the
charging contacts of the charger cradle. The Led will light in
Red color then the device is ready to begin the charging
process. The charging time depends on the battery condition
and capacity (about 5 hours). During charging process, the
Led will light in orange color gradually. When the charging
process has finished, the Led lights in green color. Remove
the battery pack or the transceiver from the battery charger
and disconnect it from the AC outlet.
Charger LED Indicator
Warning !
The battery is supplied empty and it has to be fully recharged before use.
Make sure that the radio is switched OFF during charging process.
Some complete cycles of charge/discharge will be necessary in order for the battery to reach a
peak efficiency level.
Please do not charge the battery again when it has just been charged. Otherwise, you may
damage the battery or reduce its life.
The battery charger does not switch OFF automatically when charging is complete, therefore
please remove battery or radio from the charger cradle and disconnect it from the AC outlet.
Do not recharge battery for more than 8 hours, in order to avoid battery overheating. When
the temperature is too high (over 60°C), charging stops and charger's LED will light in
yellow color. Try to recharge the battery when the temperature drops.
English
Charger Status LED Indicator Remarks
Power ON / Standby Green light
Charging Mode Red light and Orange light gradually
during charging process
Full Charging Green light
Battery Fault LED OFF
High temperature Yellow light
Battery pack is damaged
When the battery capacity is using out, the radio will keep reporting "Please charge the battery" every 10
seconds.

To install the battery
Please match battery pack with the corresponding guides on
the back side of the transceiver.
Slide and press the battery downward untill the locker placed
on the base of the radio locks the battery.
To remove the battery
To remove the battery, press the battery locker [1] placed on
the base of the radio and get the battery away [2] from the
radio.
Warning !
Please do not waste used batteries into the environment and do not trash them with the common
garbage. Please use the dedicated case for the collection of used up batteries at your supplier.
Do not attempt to open or remove the battery casing.
Do not short the battery terminals or throw the used batteries into fire.
To install / to remove the belt clip
If necessary, attach the belt clip to the back side of the tranceiver, by fixing
it with the two supplied screws.
To remove the belt clip, release the screws.
Preliminary Steps
- 5 -
English

Preliminary Steps
- 6 -
To install the external microphone (optional)
To install the external microphone, remove the protection
cover of the external microphone/speaker jack. This cover
ensures the watertight integrity of the transceiver (spray-
guard) that will not be ensured after its removing.
Insert the connector of the external microphone into the
right jack.
In order to avoid mulfunction or damage to the transceiver,
use only original microphones. Using non original accessories
will authomatically void the warranty.
Warning !
If an external earset-microphone is used, radio will not be splash proof.
WARNING !
THE RUBBER FLEXIBLE ANTENNA IS FIXED AND NOT REMOVABLE. DO NOT TRY TO TURN OR
REMOVE IT, OTHERWISE ANTENNA MAY BE BROKEN.
English

- 7 -
Getting Acquainted with the Product
GETTING ACQUAINTED WITH THE PRODUCT
1. Antenna
Fixed non removable rubber flexible antenna.
2. Channel Selector
Turn the selector to select the desired channel from 1 to 16.
3. Power ON switch and volume control
Switch on the transceiver turning the knob clockwise or counterclockwise to switch it off.
To increase the volume, turn the knob clockwise or counterclockwise to decrease it.
4. LED Indicator
The LED indicator will light in green colour when the radio is receiving a signal and in red colour
during transmission.
5. PTT key (Push-To-Talk)
To transmit, press and keep pressed the PTT key (5), then speak into the microphone with your
normal voice. To receive release the PTT key (5).
6. SIDE Key 1
This key is programmable by using dedicated software (free download at www.intek-radios.com).
The default setting is the MONITOR function (see page 10).
7. SIDE Key 2
This key is programmable by using dedicated software (free download at www.intek-radios.com).
The default setting is the MONITOR function (see page 10).
2
3
1
4
5
6
7
10
8
9
11
12
English

8. Speaker
Built-in speaker.
9. Microphone
Built-in speaker.
10. Battery Level Indicator
Switch ON the radio to check (within 5 seconds) the current battery level condition. 4 bars mean full
charge and 1 bar means low battery condition. No lighted bars mean that battery pack must be
immediately recharged.
11. External earset-microphone jack rubber cover
This cover protects the external earset-microphone jack and makes the radio splash proof.
12. Desktop Charger Contacts
GETTING STARTED
Power ON
Switch on the transceiver turning the Power/Volume knob (3)
clockwise until you hear a click, the transceiver now is in stand-by
mode and indicate (within 5 seconds) the battery level condition
(8). If the Voice Announcement function is enabled by software,
radio will automatically report the channel number.
Volume adjustment
To adjust the volume, turn the volume knob (3) while using the
SIDE keys (6 or 7), if programmed as Monitor function, to listen to
the background noise of the channels.
Channels selection
Turn the channels selector (2) to select the channels. If the Voice
Announcement function is enabled by software, radio will
automatically report the channel number.
Getting Acquainted with the Product - Getting Started
- 8 -
English

Transmission
In order to transmit, press the PTT key (5) and speak with your normal
voice, keeping the microphone (9) at about 4 cm from your mouth.
The LED indicator (4) will light in red color. Release the PTT key (5) at
the end of transmission.
If during transmission the battery voltage drops below the pre-set
minimum level, radio will automatically switch to RX mode and radio
will keep reporting "Please charge the battery".
Receiving
Release the PTT key (5) and properly adjusting volume, yo will be able to receive the incoming signals.
When receiving a signal, the LED indicator (4) will light in green colour.
ADVANCED FUNCTIONS
The following functions could be programmed only by using the dedicated PC software (free download
at www.intek-radios.com). If these functions are disable by factory setting, they will be effect after
activation.
Time-Out-Timer
This function has two purposes:
- to allow, after a set time, to listen to other urgent calls.
- to avoid to transmit for an endless time, in order to prevent overheating or damage to the
transceiver. After a programmable preset time of uninterrupted transmission, the transceiver
automatically stops the transmission emitting a warning tone (pre-set function). To stop the
warning tone, release the PTT key (5). To restart the transmission, press again the PTT key (5).
Note: the preset time is fixed at 180 seconds.
Battery Saving
This function reduces the battery consumption when no signal is received or when no operation is
performed (it means when no key is pressed, no switch is turned on/off). This function is automatically
enabled if no signals are received and if radio has not been operated for 16 seconds.
Low Battery Alert
This function warns you when it is necessary to charge the battery. If the battery level goes down to a
fixed level, radio will keep reporting "Please charge the battery" every 10 seconds. By pressing the PTT
Key (5), the transceiver will stop automatically the transmission and sound "Please charge the battery".
So please release the PTT key (5) and charge the battery.
Note: if battery level is too low, radio may power OFF automatically.
Getting Started - Advanced Functions
- 9 -
English

- 10 -
Advanced Functions
Monitor Function
This function can be enabled by programming Side keys (6/7) (default setting).
When no signal is received, the Squelch circuit automatically disables the speaker, so the background
noise desappears. To manually disable the Squelch, press and hold SIDE keys (6 or 7). This function
may be useful when you want to adjust the volume, when you want to receive a weak signal or when
you want to listen to a channel screened by CTCSS/DCS. If Side keys (6 or 7) are pressed, the Led
indicator (4) lights in green color.
Tone Squelch Function (CTCSS) / (DCS)
Reserved Transmission (CTCSS) & Digital Reserved Transmission (DCS)
39 groups of standard CTCSS and 83 groups of DCS tones are available (PC programmable).
1. Any channel may be associated to a programmed private protection CTCSS/DCS tone. A
CTCSS/DCS tone is a sub audible tone which allows to cut off and therefore not to listen to
signals transmitted from other users on the same operating channel.
2. When you receive a signal which has a tone different from the one which has been programmed
on your radio, you will not listen to this signal. For the same reason, your outgoing messages can
only be received by other radios which have the same tone as yours on that channel.
Note : Even if the use of a CTCSS/DCS tone will protect you from receiving unwanted signals, the
privacy of your transmissions is not guaranteed.
Automatic Channel Scanning
This function can be enabled when channel selector (2) is on CH16.
To operate this function, you must program the channels to be scanned.
Scanning will stop whenever a signal is received and re-start 3 seconds after the signal disappears.
English

Specifications - Optional Accessories
- 11 -
SPECIFICATIONS
General
Frequency 446.00625 - 446.09375 MHz
Channels 16
Channel spacing 12.5 KHz
DC input voltage 7.2 VDC
Operating temperature -10/+55°
Dimensions mm 58 x 35 x 225 (with antenna)
Weight 193 gr. (with battery pack)
Receiver
Sensitivity (12dB Sinad) 0.25 µV
Audio output 500mW
Transmitter
RF output power 0.5W ERP
Modulation FM
Spurious & Harmonics in compliance with the R&TTE regulations
OPTIONAL ACCESSORIES
- KME-315 External Earset-Microphone with tie clip
- KME-614 External Earset-Microphone with adjustable ear hook
- KME-801 External Earset-Microphone for security and bodyguard
- KME-100A External Earset-Microphone with tie clip
- KME-200A External Earset-Microphone with flexible boom mic and tie clip
- KME-H115 External Speaker-Microphone (light duty)
- KST-301 External Speaker-Microphone (heavy duty)
- KPG-33 PC interface USB cable
English

Channels Programming - User Information
- 12 -
CHANNEL FREQUENCY
TX
FREQUENCY
RX
CTCSS / DCS
TONE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
446.09375
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
-
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
446.09375
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
-
NO
NO
NO
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
123.0
156.7
-
FREQUENCY / CHANNELS PROGRAMMING (factory default programming)
User Information
in accordance with art. 13 of the Legislative Decree of 25th July 2005, no. 15 ”Implementation of Directives 2002/95/EC,
2002/96/EC and 2003/108/EC, relative to reduction of the use of hazardous substances in electrical and electronic
equipment, in addition to waste disposal”.
The crossed bin symbol shown on the equipment indicates that at the end of its working life the product must
be collected separately from other waste.
The user must therefore take the above equipment to the appropriate differentiated collection centres for
electronic and electro technical waste, or return it to the dealer when purchasing a new appliance of
equivalent type, in a ratio of one to one.
Appropriate differentiated waste collection for subsequent recycling, treatment and environment-friendly disposal of the
discarded equipment helps to prevent possible negative environmental and health effects and encourages recycling of
the component materials of the equipment.
Illegal disposal of the product by the user will be punished by application of the administrative fines provided for by the
legislative decree no. 22/1997 (article 50 and following of the legislative decree no. 22/1997).
English

Indice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Importante . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Informazioni per l' utente . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Disimballaggio e verifica delle parti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessori forniti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Preparazione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-18
Familiarizzare con il prodotto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
Operazioni di base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21
Funzioni supplementari . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
Specifiche tecniche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Accessori opzionali . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Programmazione canali / Avviso agli utenti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Avvertenze Importanti / Garanzia Limitata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Indice - Importante
- 13 -
IMPORTANTE !
Questo ricetrasmettitore è programmabile tramite PC, utilizzando l’apposito software
(liberamente scaricabile dal sito www.intek-radios.com) e cavetto di interfaccia (opzionale).
L’eventuale programmazione o modifica della programmazione esistente deve essere eseguita
da un tecnico specializzato o da un centro di assistenza autorizzato. Alcune funzioni del
ricetrasmettitore potrebbero essere programmate in violazione delle norme tecniche in vigore
per l’utilizzo della banda PMR- 446. E’ responsabilità dell’utente verificare che eventuali
modifiche nella programmazione delle funzioni del ricetrasmettitore siano conformi a quanto
previsto dalle norme tecniche in vigore. Modifiche al prodotto, manomissioni, alterazione delle
regolazioni interne o delle strutture esterne della radio e programmazioni in violazione delle
norme di legge fanno decadere le certificazioni e omologazioni del prodotto ed il diritto
all’utilizzo dello stesso.
INTEK s.r.l. declina qualsiasi responsabilità relativamente a modifiche della programmazione
del ricetrasmettitore, eseguite dall’utente o da terzi, dopo la consegna del prodotto.
IMPORTANTE !
Questo ricetrasmettitore è stato pre-programmato in origine, al fine di consentire all’utente
l’utilizzo immediato del prodotto dopo l’acquisto. La programmazione eseguita comprende
l’attivazione di canali/frequenze in banda PMR-446, nel rispetto delle norme tecniche in vigore
per l’utilizzo di questa banda. Per i dettagli riferirsi alla tabella a pag. 24.
Italiano

Grazie !
Vi ringraziamo per aver scelto INTEK per applicazioni civili. Siamo certi che questo ricetrasmettitore di
facile uso vi consentirà di comunicare in modo affidabile e di svolgere le vostre attività professionali con
la massima efficienza. Questo ricetrasmettitore incorpora la più avanzata tecnologia e sarete soddisfatti
del suo livello di qualità e delle sue caratteristiche tecniche.
Avviso importante per l' utente !
L’utilizzo dei ricetrasmettitori PMR 446 è regolato dalle norme di legge in vigore. Poiché le norme
stesse sono soggette a possibili variazioni, prima di utilizzare gli apparecchi, si raccomanda di
informarsi presso il proprio rivenditore o fornitore verificando gli eventuali adempimenti da osservare.
INTEK declina qualsiasi responsabilità relativamente ad un uso degli apparecchi non autorizzato o non
conforme alle norme di legge.
Sicurezza
L’utente deve conoscere e comprendere i rischi comuni legati all’uso di apparecchi ricetrasmittenti. Non
utilizzate mai il ricetrasmettitore in ambienti a rischio di esplosione (in presenza di gas, polveri, fumi,
etc.). Non utilizzare inoltre il ricetrasmettitore nelle aree di servizio o distributori di carburante.
Precauzioni
Si consiglia di osservare le seguenti precauzioni, al fine di evitare incendi, ferite personali e danni al
ricetrasmettitore:
Si suggerisce di trasmettere per alcuni minuti in quanto trasmissioni molto lunghe o alla massima
potenza del trasmettitore potrebbero surriscaldare lo stesso.
Non manomettere o modificare in alcun modo il ricetrasmettitore.
Non esporre il ricetrasmettitore per lungo tempo alla luce solare diretta e non porlo vicino a fonti
di calore.
Non porre il ricetrasmettitore in luoghi eccessivamente polverosi o umidi, inoltre non porlo su
superfici instabili.
Se sentite un odore anomalo o se vedete del fumo fuoriuscire dal ricetrasmettitore, spegnetelo
immediatamente e rimuovete il pacco batteria. Quindi contattate un centro di assistenza
autorizzato.
Non gettate batterie usate nella spazzatura. Utilizzate solo gli appositi contenitori per lo
smaltimento.
- 14 -
Informazioni per l' utente
Italiano

Disimballaggio e verifica delle parti - Accessori forniti
- 15 -
Disimballaggio e verifica delle parti
Disimballate accuratamente il ricetrasmettitore. Si raccomanda di identificare tutte le parti elencate nella
tabella seguente, prima di eliminare l’imballo. Se vi sono stati danni o mancanze durante la spedizione,
contattate immediatamente il vostro fornitore.
Accessori forniti
Pacco batterie Li-Ion 1500mAh 7.4V
Caricabatterie rapido elettronico da tavolo 230VAC
Clip da cintura
Cinghietta
Manuale d' uso
Italiano
Caricabatterie da tavolo Pacco batterie Li-Ion
Clip da cintura Cinghietta Manuale d' uso

Preparazione
- 16 -
Italiano
Ricarica della batteria
Collegare l’adattatore 230V alla presa posta sul retro del
caricatore da tavolo, come mostrato dal disegno. Collegare l'
adattatore alla presa 230VAC. Il LED verde si illuminerà a
conferma che il caricatore è alimentato. Accendere la radio e
verificare (entro 5 secondi) l' indicatore di stato di carica della
batteria (8); 4 barre indicano piena carica e nessuna barra accesa
indica che la batteria necessita di essere ricaricata a breve.
Inserire la batteria scarica o il ricetrasmettitore con la batteria
installata nel caricabatterie. Assicurarsi che i terminali della
batteria siano a contatto con quelli dei caricatore. Il LED si
illuminerà in colore rosso, quindi l’apparecchio si predispone
per iniziare la ricarica automatica della batteria. Il tempo di
ricarica dipende dallo stato di carica e dalla capacità della
batteria. Durante il processo di ricarica, il led si illuminerà
gradualmente in colore arancione. Quando la ricarica è stata
completata, il LED sarà acceso in colore verde. A questo
punto rimuovere la batteria o il ricetrasmettitore dal caricatore
e scollegare quest’ultimo dalla rete elettrica.
Indicatore LED
Avvertenze !
La batteria viene fornita scarica e deve essere quindi ricaricata prima dell’uso.
Assicurarsi che la radio sia spenta durante il processo di ricarica.
Sono necessari alcuni cicli completi di carica/scarica affinché la batteria raggiunga il massimo
livello di efficienza.
La batteria non deve essere ricaricata nuovamente se è già stata completamente caricata.
Diversamente, la vita della batteria può diminuire o la stessa essere danneggiata.
Il caricabatterie non si spegne automaticamente dopo la ricarica pertanto rimuovere la batteria o il
ricetrasmettitore dal caricatore e scollegare quest’ultimo dalla rete elettrica.
Non superare le 8 ore di ricarica, per evitare il danneggiamento della batteria. Se la
temperatura ètroppo elevata (oltre 60°C), la carica si arresta e il LED del caricatore sarà
acceso in colore giallo. Riprovare a caricare la batteria quando la temperatura èpiùbassa.
Stato di carica Indicatore LED Note
Acceso / Standby Luce verde
In carica Luce rossa e gradualmente luce
arancione durante la ricarica
Carica ultimata Luce verde
Errore batteria LED spento
Alta temperatura Luce gialla
Pacco batterie danneggiato
Se la capacità della batteria è esaurita, si udirà il messaggio sonoro "Please charge the battery" ogni 10
secondi.

Preparazione
- 17 -
Italiano
Installare la batteria
Fare coincidere il pacco batterie con le guide corrispondenti
sulla parte posteriore del ricetrasmettitore.
Fare slittare e premere contemporaneamente la batteria sul
retro del ricetrasmettitore fino a quando il blocco posto alla
base della radio si aggancia e blocca la batteria.
Rimuovere la batteria
Per rimuovere la batteria premere sul blocco [1] posto alla
base della radio e togliere la batteria [2] dalla radio come
indicato nel disegno.
Avvertenze !
Non disperdere batterie esaurite nell’ambiente e non gettarle tra i rifiuti ordinari. Utilizzate gli
appositi contenitori per la raccolta delle batterie usate o restituite le batterie da eliminare al vostro
fornitore.
Non tentare mai di rimuovere l’involucro della batteria.
Non cortocircuitare i teminali della batteria e non gettare quest' ultima nel fuoco.
Installare / rimuovere la clip da cintura
Se necessario, applicare la clip da cintura al ricetrasmettitore, fissandola
sul retro del ricetrasmettitore tramite le apposite viti in dotazione.
Per rimuovere la clip da cintura, togliere le viti di fissaggio.

- 18 -
Preparazione
Italiano
Installare un microfono esterno (opzionale)
Per poter installare il microfono esterno, occorre prima
rimuovere la copertura fissata a protezione della presa per
microfono/altoparlante esterno, che assicura anche una
tenuta stagna (anti spruzzo).
Inserire il connettore del microfono esterno nell’apposita
presa.
Per evitare malfunzionamenti o danni al ricetrasmettitore,
utilizzare esclusivamente microfoni originali. L’utilizzo di
accessori diversi da quelli originali causa automaticamente la
perdita del diritto alla garanzia.
Attenzione !
Se si utilizza un microno esterno, il ricetrasmettitore non è più a tenuta stagna.
IMPORTANTE !
L' ANTENNA FLESSIBILE IN GOMMA E' FISSA E NON RIMUOVIBILE. NON TENTARE DI
RUOTARLA O RIMUOVERLA, IN QUANTO PUO' ESSERE DANNEGGIATA.