Intek MT-446EX User manual

INSTRUCTION MANUAL
MANUALE DI ISTRUZIONI
PROFESSIONAL 2-WAY RADIO
PC PROGRAMMABLE
PMR 446 / 16CH
MT-446EX

Declaration of Conformity
With the present declaration, we certify that the following products :
INTEK MT-446EX
comply with all the technical regulations applicable to the above mentioned products
in accordance with the EC Directives 73/23/EEC, 89/336/EEC and 99/5/EC.
Type of product : PMR 446 UHF Transceiver
Details of applied standards : EN 300 296, EN 301 489-1/-5,
EN 60065
Manufacturer : INTEK S.R.L.
Via G. Marconi, 16
20090 Segrate, Italy
Tel. [phone] / Fax. [phone]
E-mail : [email protected]
Notified Body : EMCCert Dr. Rasek
Boelwiese 5, 91320 Ebermannstadt
Germany
Identification Number : 0678
Contact Reference : Armando Zanni
Tel. [phone] / Fax. [phone]
E-mail : [email protected]
Segrate, 16/04/2007 dr. Vittorio Zanetti
(General Manager)
DECLARATION OF CONFORMITY
0678
NOTICE !
It is recommended to carefully read this owner’s manual before using the product. This will also help the user to
prevent using the radio in violation of the regulations valid in the country where the product is used, as well as to
avoid any possible interferences with other services.
RoHS
2002/95/EC

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpacking and checking parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Preliminary Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Getting acquainted with the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Automatic channel scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Additional functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Frequency/Channels programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Index - Notice
- 1 -
NOTICE !
This transceiver is programmable via PC, using the dedicated software and the PC interface
cable (optional items). Any programming or modification of the original default setting must be
made by a specialised technician or by an authorised service centre. Some functions of this
transceiver might be programmed in violation of the technical rules in force for the use of the
PMR-446 band. It is the user’s responsibility to check that any modification to the programming
will be done in compliance with the current regulations. Any modification to the product,
alteration of the internal circuit, of the external structure of the radio or any programming in
violation of the current regulations will automatically void the product certification and your right
to use the product. INTEK S.R.L. declines any responsibility concerning any modification of the
product, made by the user or by a third party, after delivery of the product.
NOTICE !
This transceiver has been factory programmed, in order to use the product immediately after
purchase. The programming includes the activation of channels/frequencies in the PMR-446
band, according to the technical rules in force for the use of this band. Please refer to the table
at page 12 for details.
English

Thank you !
Thank you for choosing INTEK for your two-way business radios applications. This user friendly
transceiver will provide you with clear and reliable communications and will keep your professional
activities at peak efficiency. This transceiver incorporates the latest and most advanced technology, so
you will be pleased with its quality and its technical features.
Important notice !
The use of PMR-446 transceivers is subject to the regulations applied in the country where the product
has to be used. As regulations are usually subject to possible modifications, please check the current
regulations in your country with your dealer or local supplier. INTEK does not take any responsibility for
illegal use and operation of this product not in accordance with the regulation of the country where the
product is used.
Safety notice
The user must know and understand the common risks related to the use of transceivers. Do not use
the transceiver in environments at risk of explosion (where there are gas, dusts, smokes, etc.). Do not
use the transceiver in service areas or fuel stations, on board aircrafts, etc.
Cautions
Please observe the following precautions, in order to avoid causing fire, personal injuries or damage to
the radio:
It is suggested that each transmitted message lasts a few minutes only, since very long
transmissions at the maximum transmitter RF output power may overheat the transmitter.
Do not alter or modify in any way your transceiver.
Do not expose the transceiver for a long time to direct sunlight and do not place it close to
heat sources.
Do not expose the transceiver to excessively dusty or damp places, do not place it on
unstable surfaces.
In case of anomalous smell or smoke that leaks out from the transceiver, turn it off immediately
and remove the battery pack. Please contact an authorised service center.
Please do not dispose off used battery with common garbage. Please use the dedicated
disposal containers.
- 2 -
General Information
English

Unpacking and Checking Parts - Supplied Accessories
- 3 -
Unpacking and checking parts
Carefully unpack the product. Please identify all the parts listed below, before wasting the packaging. If
any part is missing or if the packaging shows any damage, please contact your dealer immediately.
Supplied accessories
7.2V 1200mAh Li-Ion Rechargeable Battery Pack
Electronic Quick Desk Charger
Belt Clip
Speaker-microphone Jack Cover
User Manual
Electronic Quick Desk Charger Li-Ion Battery Pack
Belt Clip
PS
CI
M
Speaker-Microphone
Jack Cover
User Manual
English

Preliminary Steps
- 4 -
Battery charging
Connect the 230VAC adaptor charger to the desk type battery charger
and to a 230VAC outlet. The Red Led will flash to confirm that the charger
is powered.
Insert the empty battery or the transceiver with the battery pack in the
battery charger. Please make sure that the charging contacts of the radio
are connected with the charging contacts of the charger cradle. The Red
Led will light then the device is ready to begin the charging process. The
charging time depends on the battery condition and capacity (about 5
hours). When the charging process has finished, the Red Led lights off
and the Green Led will light. Remove the battery pack or the transceiver
from the battery charger and disconnect it from the AC outlet.
Warning !
The battery is supplied empty and it has to be fully recharged before use.
Some complete cycles of charge/discharge will be necessary in order for the battery to reach a
peak efficiency level.
Please do not charge the battery again when it has just been charged. Otherwise, you may
damage the battery or reduce its life.
The battery charger does not switch OFF automatically when charging is complete, therefore
please remove battery or radio from the charger cradle and disconnect it from the AC outlet.
Do not recharge battery for more than 8 hours, in order to avoid battery overheating.
English

To install the battery
Please align the two battery slots with the fit runner on the lower side of
the transceiver.
Press the battery downward untill the locker placed on the rear side of the
radio hooks and fastens the battery.
To remove the battery
To remove the battery, press the battery locker placed on the rear side of
the radio and slide the battery away from the radio.
Warning !
Please do not waste used batteries into the environment and do not trash them with the common
garbage. Please use the dedicated case for the collection of used up batteries at your supplier.
Do not attempt to open or remove the battery casing.
Do not short the battery terminals or throw the used batteries into fire.
To install / to remove the belt clip
If necessary, attach the belt clip to the tranceiver, making it slide along the
fit runner placed on the rear side of the battery untill the lock will hook. To
remove the belt clip press the lock and slide the belt clip away from
the battery.
Preliminary Steps
- 5 -
English

Preliminary Steps
- 6 -
Install the external earset-microphone jack rubber cover.
If an external earset-microphone is not used, please install the earset-
microphone jack rubber cover.
Install the earset-microphone jack rubber cover, by matching the three
rubber tabs with the holes on the radio, as showed on the drawing.
If the earset-microphone jack rubber cover is removed, radio will not be
splash proof.
To install the external microphone (optional)
To install the external microphone, remove the protection cover of the
external microphone/speaker jack. This cover ensures the watertight
integrity of the transceiver (spray-guard) that will not be ensured after its
removing. Insert the connector of the external microphone into the
right jack.
In order to avoid mulfunction or damage to the transceiver, use only
original microphones. Using non original accessories will authomatically
void the warranty.
Warning !
If an external earset-microphone is used, radio will not be splash proof.
WARNING !
THE RUBBER FLEXIBLE ANTENNA IS FIXED AND NOT REMOVABLE. DO NOT TRY TO TURN OR
REMOVE IT, OTHERWISE ANTENNA MAY BE BROKEN.
English

- 7 -
Getting Acquainted with the Product
GETTING ACQUAINTED WITH THE PRODUCT
1. Antenna
Fixed non removable rubber flexible antenna.
2. Channel Selector
Turn the selector to select the desired channel from 1 to 16.
3. Power ON switch and volume control
Switch on the transceiver turning the knob clockwise or counterclockwise to switch it off.
To increase the volume, turn the knob clockwise or counterclockwise to decrease it.
4. Speaker
Built-in speaker.
5. Microphone
Built-in speaker.
6. LED Indicator
The LED indicator will light in green colour when the radio is receiving a signal, in red colour
during transmission and it will flash in red colour when, during transmission, the battery level is
low or empty.
7. PTT key (Push-To-Talk)
To transmit, press and keep pressed the PTT key (7), then speak into the microphone with your
normal voice. To receive release the PTT key (7).
1
2
3
4
5
6
7
8
9
10
English

8. MONITOR Key
Press this key to open the Squelch and release it to close the Squelch.
9. External earset-microphone jack rubber cover
This cover protects the external earset-microphone jack and makes the radio splash proof.
10. Desktop Charger Contacts
GETTING STARTED
Power ON
Switch on the transceiver turning the Power/Volume knob (3)
clockwise until you hear a click, the transceiver now is in stand-by
mode. If the transceiver emits only one beep the high power is
enabled. If it emits two beeps the low power is enabled.
Switching between high and low power
(this function may be disabled or enabled with the programming of the radio)
Turn off the transceiver. Press the PTT key (7) and at the same time
turn on the transceiver; this way the original power mode will be
changed. If only one beep is heard, the transceiver is in high power
mode. If two beeps are heard, the transceiver is in low power mode.
Volume adjustment
To adjust the volume, turn the volume knob (3) while using the
MONITOR key (8) to listen to the background noise of the channels.
Getting Acquainted with the Product - Getting Started
- 8 -
English

Channels selection
Turn the channels selector (2) to select the channels.
Transmission
In order to transmit, press the PTT key (7) and speak with your normal
voice, keeping the microphone at about 4 cm from your mouth. The
LED indicator (6) will light in red color. Release the PTT key (7) at the
end of transmission.
If during transmission the battery voltage drops below the pre-set
minimum level, radio will automatically switch to RX mode and the
LED low battery indicator (6) will blink in red colour.
Receiving
Release the PTT key (7) and properly adjusting volume, yo will be able to receive the incoming signals.
When receiving a signal, the LED indicator (6) will light in green colour.
AUTOMATIC CHANNEL SCANNING
This function can be ENABLED with the programming of the radio.
To operate this function, you must program the channels to be scanned (CH-1 to 15), but no frequency
must be programmed at CH-16.
Scan start
Set the transceiver on channel 16. Scanning will start and it will stop whenever a signal is received.
Scan end
To stop scanning, tune the transceiver on a channel 1-15.
Getting Started - Automatic Channel Scanning
- 9 -
English

- 10 -
Advanced Functions
ADVANCED FUNCTIONS
Time-Out-Timer (*)
This function has two purposes:
- to allow, after a set time, to listen to other urgent calls.
- to avoid to transmit for an endless time, in order to prevent overheating or damage to the
transceiver. After a programmable time of 30-300 seconds of uninterrupted transmission, the
transceiver automatically stops the transmission emitting a warning tone (pre-set function). To
stop the warning tone, release the PTT key (7). To restart the transmission, press again the PTT
key (7).
Battery Saving
This function reduces the battery consumption when no signal is received or when no operation is
performed (it means when no key is pressed, no switch is turned on/off). This function is automatically
enabled if no signals are received and if radio has not been operated for 10 seconds.
Low Battery Indicator
During transmission, this function warns you when it is necessary to charge the battery. If the battery
level goes down to a fixed level, the Led indicator (6) will flash in red colour and the transceiver will stop
the transmission.
Monitor (*)
When no signal is received, the Squlech circuit automatically disables the speaker, so the background
noise desappears. To manually disable the Squelch, press the MONITOR key (8). This function may be
useful when you want to adjust the volume, when you want to receive a weak signal or when you want
to listen to a channel screened by CTCSS/DCS. If the Monitor key (8) is pressed, the Led indicator (6)
lights in green color.
Tone Squelch Function (CTCSS) / (DCS) (*)
1. Any channel may be associated to a programmed private protection CTCSS/DCS tone. A
CTCSS/DCS tone is a sub audible tone which allows to cut off and therefore not to listen to
signals transmitted from other users on the same operating channel.
2. When you receive a signal which has a tone different from the one which has been programmed
on your radio, you will not listen to this signal. For the same reason, your outgoing messages can
only be received by other radios which have the same tone as yours on that channel.
Note : Even if the use of a CTCSS/DCS tone will protect you from receiving unwanted signals, the
privacy of your transmissions is not guaranteed.
(*) This function may be enabled only by using the optional programming kit.
English

Specifications - Optional Accessories
- 11 -
SPECIFICHE TECNICHE
General
Frequency 446.00625 - 446.09375 MHz
Channels 16 (15+S)
Channel spacing 12.5 KHz
DC input voltage 7.2 VDC
Operating temperature -20/+55°
Dimensions mm 58 x 120 x 35
Weight 240 gr. (with battery pack)
Receiver
Sensitivity (12dB Sinad) 0.25 µV
Audio output 500mW
Transmitter
RF output power 0.5W ERP
Modulation FM
Spurious & Harmonics in compliance with the R&TTE regulations
OPTIONAL ACCESSORIES
- KME-315 External Earset-Microphone with tie clip
- KME-100A External Earset-Microphone with tie clip
- KME-200A External Earset-Microphone with flexible boom mic and tie clip
- KME-H115 External Speaker-Microphone (light duty)
- KST-301 External Speaker-Microphone (heavy duty)
- CDMT-46EX Programming Kit (PC interface cable and software CD)
English

Channels Programming - User Information
- 12 -
CHANNEL FREQUENCY
TX
FREQUENCY
RX
CTCSS / DCS
TONE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
446.09375
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
-
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
446.09375
446.00625
446.01875
446.03125
446.04375
446.05625
446.06875
446.08125
-
NO
NO
NO
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
123.0
156.7
-
FREQUENCY / CHANNELS PROGRAMMING (factory default programming)
User Information
in accordance with art. 13 of the Legislative Decree of 25th July 2005, no. 15 ”Implementation of Directives 2002/95/EC,
2002/96/EC and 2003/108/EC, relative to reduction of the use of hazardous substances in electrical and electronic
equipment, in addition to waste disposal”.
The crossed bin symbol shown on the equipment indicates that at the end of its working life the product must
be collected separately from other waste.
The user must therefore take the above equipment to the appropriate differentiated collection centres for
electronic and electro technical waste, or return it to the dealer when purchasing a new appliance of
equivalent type, in a ratio of one to one.
Appropriate differentiated waste collection for subsequent recycling, treatment and environment-friendly disposal of the
discarded equipment helps to prevent possible negative environmental and health effects and encourages recycling of
the component materials of the equipment.
Illegal disposal of the product by the user will be punished by application of the administrative fines provided for by the
legislative decree no. 22/1997 (article 50 and following of the legislative decree no. 22/1997).
English

Indice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Importante . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Informazioni per l' utente . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Disimballaggio e verifica delle parti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessori forniti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Preparazione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-18
Familiarizzare con il prodotto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
Operazioni di base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21
Scansione automatica dei canali . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Funzioni supplementari . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Specifiche tecniche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Accessori opzionali . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Programmazione canali / Avviso agli utenti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Avvertenze Importanti / Garanzia Limitata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Indice - Importante
- 13 -
IMPORTANTE !
Questo ricetrasmettitore è programmabile tramite PC, utilizzando l’apposito software e cavetto
di interfaccia (opzionali). L’eventuale programmazione o modifica della programmazione
esistente deve essere eseguita da un tecnico specializzato o da un centro di assistenza
autorizzato. Alcune funzioni del ricetrasmettitore potrebbero essere programmate in violazione
delle norme tecniche in vigore per l’utilizzo della banda PMR- 446. E’ responsabilità dell’utente
verificare che eventuali modifiche nella programmazione delle funzioni del ricetrasmettitore
siano conformi a quanto previsto dalle norme tecniche in vigore. Modifiche al prodotto,
manomissioni, alterazione delle regolazioni interne o delle strutture esterne della radio e
programmazioni in violazione delle norme di legge fanno decadere le certificazioni e
omologazioni del prodotto ed il diritto all’utilizzo dello stesso.
INTEK s.r.l. declina qualsiasi responsabilità relativamente a modifiche della programmazione
del ricetrasmettitore, eseguite dall’utente o da terzi, dopo la consegna del prodotto.
IMPORTANTE !
Questo ricetrasmettitore è stato pre-programmato in origine, al fine di consentire all’utente
l’utilizzo immediato del prodotto dopo l’acquisto. La programmazione eseguita comprende
l’attivazione di canali/frequenze in banda PMR-446, nel rispetto delle norme tecniche in vigore
per l’utilizzo di questa banda. Per i dettagli riferirsi alla tabella a pag. 24.
Italiano

Grazie !
Vi ringraziamo per aver scelto INTEK per applicazioni civili. Siamo certi che questo ricetrasmettitore di
facile uso vi consentirà di comunicare in modo affidabile e di svolgere le vostre attività professionali con
la massima efficienza. Questo ricetrasmettitore incorpora la più avanzata tecnologia e sarete soddisfatti
del suo livello di qualità e delle sue caratteristiche tecniche.
Avviso importante per l' utente !
L’utilizzo dei ricetrasmettitori PMR 446 è regolato dalle norme di legge in vigore. Poiché le norme
stesse sono soggette a possibili variazioni, prima di utilizzare gli apparecchi, si raccomanda di
informarsi presso il proprio rivenditore o fornitore verificando gli eventuali adempimenti da osservare.
INTEK declina qualsiasi responsabilità relativamente ad un uso degli apparecchi non autorizzato o non
conforme alle norme di legge.
Sicurezza
L’utente deve conoscere e comprendere i rischi comuni legati all’uso di apparecchi ricetrasmittenti. Non
utilizzate mai il ricetrasmettitore in ambienti a rischio di esplosione (in presenza di gas, polveri, fumi,
etc.). Non utilizzare inoltre il ricetrasmettitore nelle aree di servizio o distributori di carburante.
Precauzioni
Si consiglia di osservare le seguenti precauzioni, al fine di evitare incendi, ferite personali e danni al
ricetrasmettitore:
Si suggerisce di trasmettere per alcuni minuti in quanto trasmissioni molto lunghe o alla massima
potenza del trasmettitore potrebbero surriscaldare lo stesso.
Non manomettere o modificare in alcun modo il ricetrasmettitore.
Non esporre il ricetrasmettitore per lungo tempo alla luce solare diretta e non porlo vicino a fonti
di calore.
Non porre il ricetrasmettitore in luoghi eccessivamente polverosi o umidi, inoltre non porlo su
superfici instabili.
Se sentite un odore anomalo o se vedete del fumo fuoriuscire dal ricetrasmettitore, spegnetelo
immediatamente e rimuovete il pacco batteria. Quindi contattate un centro di assistenza
autorizzato.
Non gettate batterie usate nella spazzatura. Utilizzate solo gli appositi contenitori per lo
smaltimento.
- 14 -
Informazioni per l' utente
Italiano

Disimballaggio e verifica delle parti - Accessori forniti
- 15 -
Italiano
Caricabatterie da tavolo Batteria Li-Ion
Clip da cintura
PS
CI
M
Chiusura per presa
earset-mic
Manuale d' uso
Disimballaggio e verifica delle parti
Disimballate accuratamente il ricetrasmettitore. Si raccomanda di identificare tutte le parti elencate nella
tabella seguente, prima di eliminare l’imballo. Se vi sono stati danni o mancanze durante la spedizione,
contattate immediatamente il vostro fornitore.
Accessori forniti
Pacco batteria Li-Ion 1200mAh 7.2V
Caricabatterie rapido elettronico da tavolo 230VAC
Clip da cintura
Chiusura per presa earset-mic
Manuale d' uso

Preparazione
- 16 -
Italiano
Ricarica della batteria
Collegare l’adattatore 230V alla presa posta sul retro del caricatore da
tavolo, come mostrato dal disegno. Collegare l' adattatore alla presa
230VAC. Il LED rosso inizierà a lampeggiare.
Inserire la batteria scarica o il ricetrasmettitore con la batteria installata nel
caricabatteria. Assicurarsi che i terminali della batteria siano a contatto
con quelli dei caricatore. Il LED rosso smetterà di lampeggiare e rimarrà
acceso, quindi l’apparecchio si predispone per iniziare la ricarica
automatica della batteria. Il tempo di ricarica dipende dallo stato di carica
e dalla capacità della batteria. Quando la ricarica è stata completata, il
LED di colore verde sarà acceso e il LED di colore rosso sarà spento. A
questo punto rimuovere la batteria o il ricetrasmettitore dal caricatore e
scollegare quest’ultimo dalla rete elettrica.
Avvertenze !
La batteria viene fornita scarica e deve essere quindi ricaricata prima dell’uso.
Sono necessari alcuni cicli completi di carica/scarica affinché la batteria raggiunga il massimo
livello di efficienza.
La batteria non deve essere ricaricata nuovamente se è già stata completamente caricata.
Diversamente, la vita della batteria può diminuire o la stessa essere danneggiata.
Il caricabatterie non si spegne automaticamente dopo la ricarica pertanto rimuovere la batteria o il
ricetrasmettitore dal caricatore e scollegare quest’ultimo dalla rete elettrica.
Non superare le 8 ore di ricarica, per evitare il danneggiamento della batteria.

Preparazione
- 17 -
Italiano
Installare la batteria
Fare coincidere le 4 scanalature della batteria con le guide corrispondenti
sulla parte posteriore del ricetrasmettitore.
Fare scivolare la batteria sul retro del ricetrasmettitore fino a quando il
blocco posto alla base della radio si aggancia e blocca la batteria.
Rimuovere la batteria
Per rimuovere la batteria premere sul blocco posto alla base della radio e
far scivolare via la batteria dalla radio.
Avvertenze !
Non disperdere batterie esaurite nell’ambiente e non gettarle tra i rifiuti ordinari. Utilizzate gli
appositi contenitori per la raccolta delle batterie usate o restituite le batterie da eliminare al vostro
fornitore.
Non tentare mai di rimuovere l’involucro della batteria.
Non cortocircuitare i teminali della batteria e non gettare quest' ultima nel fuoco.
Installare la clip da cintura
Se necessario, applicare la clip da cintura al ricetrasmettitore, facendola
scivolare nell’apposita scanalatura posta sul retro della batteria fino a
quando il blocco metallico si aggancia. Per rimuovere la clip premere sul
blocco metallico e farla scivolare via dalla batteria.

- 18 -
Preparazione
Italiano
Installare la chiusura per la presa earset-mic
Se non si utilizza un microfono-altoparlante esterno, coprire la presa con il
coperchio in gomma in dotazione.
Applicare il coperchio facendo coincidere i 3 dentelli in gomma con i 3 fori
posti sul lato destro della radio come mostrato nel disegno.
Questa copertura assicura inoltre la tenuta stagna (anti spruzzo) del
ricetrasmettitore, che non sarà quindi più garantita dopo la sua rimozione.
Installare un microfono esterno (opzionale)
Per poter installare il microfono esterno, occorre prima rimuovere la
copertura fissata a protezione della presa per microfono/altoparlante
esterno.
Inserire il connettore del microfono esterno nell’apposita presa.
Per evitare malfunzionamenti o danni al ricetrasmettitore, utilizzare
esclusivamente microfoni originali. L’utilizzo di accessori diversi da quelli
originali causa automaticamente la perdita del diritto alla garanzia.
Attenzione :
Se si utilizza un microno esterno, il ricetrasmettitore non è più a tenuta stagna.
IMPORTANTE !
L' ANTENNA FLESSIBILE IN GOMMA E' FISSA E NON RIMUOVIBILE. NON TENTARE DI
RUOTARLA O RIMUOVERLA, IN QUANTO PUO' ESSERE DANNEGGIATA.