Intel XP-P41533E User manual

M-040602
XP-P4I533E
Intel®Pentium®4 Processor Motherboard
User's Manual

Motherboard
XP-P4I533E
May 18, 2004
May 18, 2004
XP-P4I533E
Motherboard
CopyrightDeclaration
©2004 Gigatrend Technology Co., Ltd. All rights reserved. No part of this manual may be
reproduced, copied, translated, or transmitted in any form or by any means without express
permission from Gigatrend Technology. Companies and product names mentioned in this
document are trademarks or registered trademarks of their respective owners.
LegalDisclaimer
The information and content of this document is provided "as is", without warranty of any kind,
express or implied, including but not limited to the warranties of merchantability, fitness for a
particular purpose and non-infringement. Gigatrend Technology assumes no responsibility for
errors or omissions in this document or other documents which are referenced by or linked to
this document. The content of this document are subject to change without prior notice.
Gigatrend Technology may make improvements and/or changes in the product described in
this publication at any time and without prior notice. In no event shall Gigatrend Technology be
liable for any special, incidental, indirect or consequential damages of any kind arising out of
or in connection with the use or performance of this document. If you are uncertain about any
installation procedures, please consult a qualified computer technician.
Termsof Use
To avoid unnecessary errors of operation, please consult the user manual prior to hardware
installation. For more up-to-date information, please link to our company website at http://
www.axper.com.tw
Prior to beginning installation procedures, please make sure that your computer turned off and
is connected to a grounded power outlet. If your system is not turned off during installation,
this could result in harm or damage to the motherboard, the components as well as to the
user.

Contents
MotherboardLayout ........................................................................4
1. ProductionIntroduction ...............................................................
51.1. FeatureSummary ............................................................................. 5
1.2. I/OBackPanelandConnectors&JumperSetting............................. 6
1.2.1. I/O Back Panel ..............................................................................6
1.2.2. Connectors&Jumper Setting ..........................................................6
2. HardwareInstallation ................................................................9
2.1. Installation of a Pentium 4 CPU and Fan Sink................................ 10
2.2. Installation of Memory ..................................................................... 10
2.3. Installation of the Graphics Card ......................................................11
3. BIOSSetup............................................................................13
3.1. SetupScreenFeatures (BIOSversion:E5)..................................... 13
3.2. StandardCMOSFeatures............................................................... 14
3.3. AdvancedBIOSFeatures ............................................................... 16
3.4. IntegratedPeripherals ..................................................................... 17
3.5. PowerManagementSetup.............................................................. 20
3.6. PnP/PCIConfiguration .................................................................... 21
3.7. PC Health Status ............................................................................. 22
3.8. Frequency/VoltageControl.............................................................. 23
3.9. TopPerformance ............................................................................. 25
3.10. LoadFail-SafeDefaults................................................................... 25
3.11. LoadOptimizedDefaults ................................................................. 25
3.12. SetUserPassword ......................................................................... 25
3.13. Save & Exit Setup ........................................................................... 25
3.14. Exit Without Saving ......................................................................... 25
4. DriverInstallation....................................................................26

4
English
Motherboard Layout
XP-P4I533E
KB_MS
COMA
ATX_12V
CD_IN
F_AUDIO
F_PANEL
BAT
Intel ICH4
Intel 845E
SOCKET 478
CPU_FAN
ATX
FDD
IDE2
PCI1
PCI2
PCI3
DDR1
CODEC
SMSC
BIOS
COMB
IDE1
CLR_CMOS
F_USB1 PWR_LED
USB LAN
DDR2
LPT
GAME
LINE_IN
LINE_OUTMIC_IN
RTL8100C
DDR3
AGP
PCI4
PCI5
SYS_FAN

English
5
CPU Socket 478 for Intel®Pentium®4 (Northwood) with HT Technology
Intel®Pentium®4 400/533MHz FSB
2nd cache depends on CPU
Chipset North Bridge: Intel®845E
South Bridge: Intel®ICH4
Memory 3 184-pin DDR DIMM sockets, supports up to 3GB DRAM (Max)
Supports DDR200/DDR266 DIMM
Supports only 2.5V DDR SDRAM
Slots 1 AGP slot device support
5 PCI slots support 33MHz & PCI 2.2 compliant
On-Board IDE 2 IDE controller provide IDE HDD/CD-ROM(IDE1, IDE2) with PIO,
Bus Master (Ultra DMA33/ATA66/ATA100) operation modes
Can connect up to 4 IDE devices
On-Board Floppy 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and
2.88M bytes
On-Board Peripherals 1 Parallel port supports Normal/EPP/ECP mode
2 Serial port (COMA, COMB)
4 USB 2.0/1.1 ports (2 x Rear, 2 x Front by cable)
1 Front Audio connector
1 PS/2 Keyboard
1 PS/2 Mouse
On-Board LAN Builit-in RTL8100C chipset
1 RJ45 port
On-Board Sound C-Media 9761 CODEC
Support 6 channel
Line Out / Line In / Mic In
CD In
BIOS Licensed AWARD BIOS
Supports BIOSNOW!
I/O Control SMSC
Hardware Monitor CPU Fan Revolution detect
CPU temperature detect
System Voltage detect
Form Factor ATX size form factor, 29.5cm x 20.0cm
1. Production Introduction
The user manual provides steps related to quick installation. If you wish to view complete
product information, please select the " ",Open User Manual button located on the driver
CD or link to our website at http://www.axper.com to received the most up-to-date information.
1.1. Feature Summary

6
English
PS/2
Keyboard
PS/2
Mouse LAN
USB COMB
Parallel Port
COM A
Game Port
Line Out MIC In
1.2. I/O Back Panel and Connectors&Jumper Setting
1.2.2. Connectors&JumperSetting
FDD(FloppyDisk Drive Connector)
The FDD connector is able to connect a single floppy disk drive via a FDD cable. Usually one
edge of the FDD cable is marked in red, please attach this marked edge to position 1 on the
connector.
IDE1 / IDE2 (IDE1 and IDE2 Connector)
The IDE connector is able to connect two IDE devices via an IDE cable and requires checking
of the IDE jumper setting. It is recommended that the hard drive be connected to the first IDE
connector while the optical drive be connected to the second IDE connector.
1.2.1. I/O Back Panel
PS/2 Keyboard Connects PS/2 standard keyboard and PS/2 standard
PS/2 Mouse connector mouse
USB Prior to use, please make sure that your system as well
(Universal Serial Bus Port) as the connected attachments support the USB interface.
If driver installation is required, please consult the USB
section of the user manual.
LAN (RJ45 LAN Port) Internet connection with speed of up to10/100Mbps
Parallel port (LPT) Connects to printer
COMA/COMB (Serial port) Connects to serial-based mouse or data processing devices
LineOut Connects to speakers or headphones
Line In Connects to optical devices, CD players and other audio
input devices
Mic In Connects to microphone
1
34
2
33
40 2
39 1

English
7
CPU_FAN(CPUFanPowerConnector);SYS_FAN(SystemFanPowerConnector)
The CPU_Fan power connector provides the largest amount of power to the CPU fan at
600mA. You can connect the casing fan to the SYS_FAN connector to enhance system cooling.
ATX_12V(+12VPower Connector)
The ATX_12V power connector provides power to the CPU. If this connector is not Attached,
the system will not start.
ATX(ATXPowerConnector)
The ATX power connector provides power to the motherboard. Prior to connection, please
make sure that the power supply is disconnected.
F_PANEL (Front Panel Control Connector)
The F_Panel Control Connector connects to certain connectors on the front panel of the
system casing such as IDE Hard Disk Active LED, speaker, reset, and power on/off connectors.
You can use the schematic diagram below as the basis for connection.
PIN SIGNAL
1GND
2GND
3+12V
4+12V
20
11
10
1
PIN SIGNAL
HD IDE Hard Disk Active LED
SPK SpeakerConnector
RES ResetSwitch
PW SoftPowerConnector
MSG MessageLED/Power/SleepLED
NC NC
PIN SIGNAL
13.3V
23.3V
3GND
4VCC
5GND
6VCC
7GND
8PowerGood
95VSB (stand by +5V)
10 +12V
PIN SIGNAL
11 3.3V
12 -12V
13 GND
14 PS_ON(softon/off)
15 GND
16 GND
17 GND
18 -5V
19 VCC
20 VCC
PIN SIGNAL
1GND
2+12V
3Sense
1
3
2
4
1
219
20
HD-
HD+
RES+
RES-
NC
SPK-
MSG-
MSG+
PW-
PW+
SPK+
1

8
English
F_AUDIO(FrontAudio Connector)
Connects to the audio connector located on the front panel of the system casing (dependent
on case design). When use of the front panel audio connector is required, please remove the
5-6 pin, 9-10pin jumper. Please note that use of only the front panel audio connector or the
rear panel audio connector is permitted.
CD_IN (Optical Drive Audio Connector)
Connects CD-ROM or DVD-ROM audio connector.
1
PIN SIGNAL
1MIC
2GND
3MIC_BIAS
4POWER
5FrontAudio(R)
PIN SIGNAL
6RearAudio(R)
7Reserved
8NO PIN
9Front Audio (L)
10 RearAudio(L)
PWR_LED
Connects to the system power LED indicator whereby the power is indicated as ON or OFF.
However, the indicator will flash when the system is suspended.
1PIN SIGNAL
1MPD+
2MPD-
3MPD-
PIN SIGNAL
1CD_L
2GND
3GND
4CD_R
1
109
2
CLR_CMOS(Clear CMOS)
You can clear the motherboard CMOS with the jumper to return your system to its initial
status. To prevent improper usage, the jumper does not include the jumper plug. If you wish to
use the Clear CMOS function, please short circuit the 1-2Pin.
1
Open:Normal
Short : Clear CMOS
1
F_USB1(FrontUSBConnector)
Connects to the USB connector located on the front panel of the system casing (dependent on
case design). Note: Please make sure that each USB connection matches its designated
position. If connections are made incorrectly, the result can lead to inability to use the function
or even damage.
210
19
PIN SIGNAL
6USBDy+
7GND
8GND
9NO PIN
10 NC
PIN SIGNAL
1POWER
2POWER
3USB Dx-
4USB Dy-
5USB Dx+

English
9
The improper removal of the battery can result in harm. When replacing a
battery, please make sure you use one that is of similar brand and model
number.
For information related to battery specifications and precautions, please refer
to the manufacturer instructions.
If you wish to delete the data stored in the CMOS, please follow the steps
below:
1. Please turn off your computer and unplug the power.
2. Remove the battery from the motherboard.
3. Wait 30 seconds and then replace the battery onto the motherboard.
4. Plug in the power supply and turn on your system.
BAT1(Battery)
+
1. Please make sure that the CPU used is supported by your motherboard.
2. Please be aware of the placement position of the CPU. If the CPU does not
insert properly, do not apply force but check the placement position.
3. Please make sure that an even layer of heat sink paste is added between the
CPU and the fan sink.
4. Please do not turn on the power prior to installing the fan sink. Doing so can
result in overheating and lead to permanent damage to the CPU.
5. Please follow the CPU specifications when setting the frequency. It is not
recommended that system speed settings exceed that of hardware
specifications. If you wish to set your system speed to exceed the recom
mended specifications, please check your hardware specifications eg: CPU,
graphics card, memory, hard drive
The following must be supported to allow the use of Hyper-Threading Technology:
- an Intel Pentium 4 CPU with HT
- a motherboard supporting HT
- HT selection feature within BIOS
- an operating system supporting HT
2. Hardware Installation

10
English
3
Position and attach the clips on one end of the fan sink firmly
atop the CPU. Please do the same for the clips on the other
end of the fan sink.
2
When the CPU is inserted into its position, gently press the
metal lever downwards until a click is heard. Then add an
even layer of heat sink paste between the CPU and fan sink
for heat dissipation.
2.1. Installation of a Pentium 4 CPU and Fan Sink
1
Note the small gold colored triangle on one corner of the CPU.
Place the triangle in the corner closest to the metal lever and
gently insert the CPU into its position.
4
Connect the 3-pin cooler power connector to the CPU Fan
connector located on the motherboard.
2.2. Installation of Memory
1. Before installing or removing memory, please make sure that the computer power
is turned off to prevent hardware damage.
2. Please make sure that the memory used is supported by the motherboard.
3. Memory modules have a foolproof insertion design. The memory can be in
stalled only when facing the correct position. If you cannot insert the module,
please switch directions.
4. It is recommended that memory of similar capacity, specifications and brand be
used.
The motherboard supports DIMM memory modules, whereby BIOS will automatically detect
memory capacity and specifications. Memory modules are designed so that they can be
inserted only in one direction.