Intelbras XAS 4010 SMART User manual

User manual
XAS 4010 SMART
English

XAS 4010 SMART
Sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The XAS 4010 Smart wireless aperture sensor was developed by Intelbras with 100%
digital technology. The sensor is mounted in SMD components and can be installed
in most products that work at the same frequency and modulation available on the
market.
Operates on FSK or OOK modulation.

Care and safety
» Follow all instructions in the manual for assembling and installing the product.
» LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or perform
any type of processing of personal data from this product.
» This product is intended for indoor and semi-open environments.
» Respect the GAP distance (distance between the sensor and the magnet).
» Conrm that the installation location is stable and appropriate.
» Wireless communication technology, when exposed to environments with high power radia-
tion, may suffer interference and have its performance impaired, for example: locations close
to TV towers, AM/FM radio stations, amateur radio stations, etc.
» Do not expose the XAS 4010 Smart Magnetic Sensor to direct sunlight, rain or moisture.
» For your safety, test the product and systems at least once a week. This is necessary due to
changing environmental conditions, electrical or electronic interruptions, and tampering.Take
all necessary precautions for the safety and security of your property.

Índice
1.Technical specications 5
2.Characteristics 5
3.Product 6
4.Sensor opening 6
5.Registering the XAS 4010 Smart sensor 7
6.XAS 4010 Smart Sensor supervision setup 8
7.Installation 9
8.Battery 11
9.Test 11
10.Homologation 11
Warranty term 12

5
1.Technical specications
Operating voltage Battery 3 V Lithium, model CR2032
Operating current 900 nA
Trigger indication Red LED
RF range 100 meters without hurdles
Transmission frequency 433.92 MHz
Detection Reed Switch SMD
Modulation Supervised (FSK) or unsupervised (OOK)
Baud rate OOK 2 KBps (open source)
Anti jamming Against external interference
Installation environment Internal and Semi-open
Opening gap 8~12mm
Closing gap 6~10 mm
Operating Temperature -10°C to 50°C
Dimensions (W × H × D) Sensor: 37×46×11 mm
Magnet: 11 × 31 × 9mm
Gross weight 0,06 Kg
Net weight 0,04 Kg
2.Characteristics
» Low battery indication;
» Supervised (FSK) or unsupervised (OOK);
» Long-lasting lithium battery;
» SMD reed switch;
» Transmission frequency 433.92 MHz.

6
3.Product
1
2
3
44
57
4
4
6
PAD PAD
FSK
8
1. Sensor cover
2. Light conductor (LED)
3. Sensor base
4. Screw hole for xing
5. Magnet cover
6. Magnet base
7. Battery contact
8. OOK/FSK track
4.Sensor opening
To access the XAS 4010 Smart board to change the battery or change the FSK/OOK
supervision, just remove the cover through the latch, it is not necessary to use tools. This
way the plate will be exposed and ready for handling.
Sensor Imã
Trava
Sensor
Magnet
Lock

7
Remove the board, then insert the battery (model CR2032), respecting the polarity.
CR 2032
3V
PAD PAD
FSK
PAD PAD
FSK
5.Registering the XAS 4010 Smart sensor
To register the XAS 4010 Smart sensor code in the alarm control panel, follow the
procedure below:
Insert the LITHIUM 3 Vdc battery - CR 2032, then type the command to register the
wireless device in the alarm center that will be used (Check the procedure in the
alarm center manual).Then perform a shot moving the magnet away from the sensor,
if the sensor is in a door for example, just open it observing if the LED will light up.
If the LED lights up, it indicates that there was a trip or transmission occurred, if the
LED does not light up, check the battery.
» Low battery sensor: the XAS 4010 Smart has a battery level meter, which me-
asures the voltage and noties you of the best time to change it, if the sensor
ashes the LED quickly in the opening, it indicates low battery level. If the alarm
center is Intelbras, the sensor low battery warning will be indicated on the product
panel. The sensor sends low battery warning in both OOK and FSK modulation.

8
6.XAS 4010 Smart Sensor supervision setup
The XAS 4010 Smart sensor allows you to select between supervised (FSK) and un-
supervised (OOK) modes. To switch between supervision modes, simply remove the
battery from the sensor, open the OOK/FSK jumper indicated on the board (and then
replace the battery), after which the sensor will operate in supervised mode (FSK).
Changing from supervised mode (FSK) to non-supervised mode (OOK) is also simple,
just remove the battery from the sensor, close the OOK/FSK jumper terminals again
and replace the battery, after which the sensor will return to operating mode. unat-
tended mode (OOK). Factory default: unsupervised (OOK)
In FSK modulation, the sensor transmits opening and closing and periodically super-
vises the sensor.
Com Trilha
Não supervisionado
OOK
PAD PAD
FSK
Sem Trilha
Supervisionado
FSK
PAD PAD
FSK
PAD PAD
FSK
PAD PAD
FSK
With track Without
supervision OOK
No supervised
FSK tracking

9
7.Installation
The XAS 4010 Smart sensor can be xed using a double face or cover. If chosen as
an option with a double-sided t, clean the surface that will be in direct contact with
the t and then place on the product base. To use the lid, just open the sensor and
use the holes to pass the lid located on the base of the product, as shown in the
following gure.
Base sensor Base imã
Instalação com parafuso
Base sensor Base imã
Instalação com fita dupla face
Fita
Screw installation
Sensor base Sensor baseMagnet base
Tape
Tornillo
ranurado
simple n.º 2
Magnet base
Installation with double-sided tape
Important: check if the GAP distance (distance between the sensor and the image)
is within the specication, to avoid unwanted triggering in the event of any vibration
in the structure in which the sensor is installed.
Note: the type of surface where the sensor is installed may inuence the distance
from the GAP.
» GAP opening: 8 ~ 12 mm
» GAP closure: 6 ~ 10 mm
GAP

10
To close the sensor, check the pin located on the base, it must be positioned on the
same side as the battery, after positioning the base, just press it for locking, there is only
one way to close the sensor, check image 01 To close the magnet, just position the base
and press it, image 02.
Pino
Aperte
para
travar
Aperte
para
travar
Figura 01 Figura 02
Pin
Press to
lock
Press to
lock
Figure 01 Figure 02
The sensor must be installed according to the images below, with the magnet aligned
with the sensor body and with the smallest possible distance between them, so that
the magnet is in contact with the magnetic eld sensor.
Note: for closing and opening the SMD magnetic eld sensor, the distances from the
GAP must be respected.

11
8.Battery
Use only quality batteries, sized correctly for the device. The battery model must be CR2032, using one (1)
battery per transmitter.
This product has an internal battery. After their useful life, batteries must
be delivered to an authorized Intelbras technical assistance or directly carry
out the environmentally appropriate nal destination, avoiding environmental
and health impacts. If you prefer, the battery, as well as other unused
Intelbras brand electronics, can be discarded at any Green Eletron collection
point (electronic waste manager to which we are associated). If you have any
questions about the reverse logistics process, please contact us by calling
(48) 2106-0006 or 0800 704 2767 (Monday to Friday from 8 am to 8 pm and
Saturdays from 8 am to 6 pm) or by e-mail -mail [e-mail].
9.Test
Once installed and in operation, check that the control panel is receiving the sensor
opening information, in case of any failure, it is necessary to reposition the sensor or
the control panel. Be sure to take all precautions and follow installation recommen-
dations to get the best operating performance from your product.
10.Homologation
This equipment is not entitled to protection against harmful interference and may not
cause interference in duly authorized systems.
This is a product approved by Anatel, the approval number can be found on the
product label, for queries visit the website: sistemas.anatel.gov.br/sch.

12
Warranty term
This contractual warranty is granted under the following conditions:
Customer name:
Customer signatre:
Invoice number:
Purchase date:
Version: Serial Number:
Dealer:
1. All parts, pieces and components of the product are warranted against any ma-
nufacturing defects it may present for a period of 1 (one) year, this period being
3 (three) months of legal warranty plus 9 (nine) months of contractual warranty,
counted from the date of purchase of the product by the Consumer, as stated in the
purchase invoice for the product, which is an integral part of this Term nationwide.
This contractual warranty includes the express exchange of products that have a
manufacturing defect. If no manufacturing defect is found, but instead any defect
arising from inappropriate use is found, the Consumer shall bear these expenses.
2. The installation of the product must be done in accordance with the Product Manual
and/or Installation Guide. If your product requires installation and conguration by
a trained technician, look for a suitable and specialized professional, whereas the
costs of these services are not included in the value of the product.
3. Once the defect is found, the Consumer shall immediately contact the Authorized
Service nearest to the list provided by the manufacturer – only these are authorized
to examine and remedy the defect during the warranty period provided herein. If
this is not respected, this warranty will lose its validity, as it will be characterized as
a violation of the product.
4. In the event that the Consumer requests home service, he/she should go to the nea-
rest Authorized Service for consultation of the technical visitation fee. If the need to
withdraw the product is found, the resulting expenses such as transportation and se-
curity for the round trip of the product are under the responsibility of the Consumer.

13
5. The warranty will totally lose its validity in the event of any of the following hypothe-
ses: a) if the defect is not a manufacturing defect, but caused by the Consumer or
by third parties unknown by the manufacturer; b) if damage to the product is arises
from accidents, damages, agents of nature (lightning, oods, landslides etc.), humi-
dity, voltage in the electrical network (overvoltage caused by accidents or excessive
uctuations in the network), installation/use not in accordance with the manual
6. This warranty does not cover data loss, therefore, it is recommended, if this is the
case of the product, that the Consumer regularly backs up the data contained in
the product.
7. Intelbras is not responsible for the installation of this product, as well as for any
attempted fraud and/or sabotage of its products. Keep up-to-date software and
applications updates, if applicable, as well as the required network protections to
protect against intrusions (hackers). The equipment is warranted against defects
within its normal conditions of use, and it is important to be aware that, as it is an
electronic equipment, it is not free from fraud and scams that may interfere with its
correct functioning.
8. After its useful life, the product must be delivered to a technical assistance autho-
rized by Intelbras or directly to the environmentally appropriate nal destination,
avoiding environmental and health impacts. If you prefer, the battery, as well as
other unused Intelbras electronics, can be disposed of at any Green Eletron collec-
tion point (electronic waste manager to which we are associated). In case of doubt
about the reverse logistics process, please contact us by phone [phone]
or 0800 7042767 (Monday to Friday, 8am-8pm / Saturdays, 8am-6pm) or by email
[e-mail]
With these as the conditions of this complementary Warranty Term, Intelbras SA re-
serves the right to change the general, technical and aesthetic features of its products
without prior notice.
All images in this package are illustrative.

01.23
Made in Brazil
Customer Support: (48) 2106 0006
Forum: forum.intelbras.com.br
Support via chat: intelbras.com.br/suporte-tecnico
Support via e-mail: [e-mail]
Customer Service: 0800 7042767
Where to buy? Who installs it? 0800 7245115
Produced by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira
Rodovia BR 459, km 124, n° 1325 – Distrito Industrial – Santa Rita do Sapucaí/MG – 37540-000
CNPJ 82.901.000/0016-03 – www.intelbras.com.br