Intelligent Home DT-GSM User manual

DT-GSM
User Manual
GSM Interface 2-wire series
www.intelligenthomeonline.com

The GSM Interface is designed for 2-wire series video door entry systems. Enables to
divert calls from Door Station to a land line telephone or a mobile via Mobile Network.
Requires activated SIM card with credit on it
• Maximum 3 telephone numbers can be
programmed
• Only monitors with ‘Call Divert’
function are compatible
• One only GSM Interface per system needed
• Application:House and Apartments systems
60 mm
72 mm
90 mm
About GSM Interface
1. Terminal Introduction
1
Features:
1 2 3 4 5 6
ON
SETUP SIM OUTPUT INPUT
SETUP: DIP switches
SIM: SIM card slot
Output: Output port, connect to Video Monitor
Input: Input port, connect to power supply

2
Power
LED BUTTON
Network
Status Transfer
Reset Signal
Quality
Recover REV
Conguration:
LED indicator Description
Power
-LED off - GSM not working
-LEDashesrapidly - systemerror
-Steady on - GSM worksnormally
Network
-LED off - SIM card is not detected
-LEDashesslowly - SIMcardisdetectedbutnot registered
-LEDashesrapidly - SIMcardisdetectedandregistered
successfully, but initialization was unsuccessful
-Steady on -GSM worksnormally
Status -LED flashes ones - system receives the effective instruction
Transfer
-LED off - there is no call divert
-LEDashesslowly -GSMinthedivertawaitingstate
-LEDashes3timesrapidly - diver hasfailed
-Steady on - the system in the talking state

3
Step 1. Mount the din rail to the wall with screws
Step 2.Pull down the mounting buckle, then hang
the unit on din rail
Din rail
Din rail
Mounting Buckle
Antenna
There is a magnet in the base of antenna. The
antenna could be mounted on a din rail on a side of
the unit or on any other metal surface
2. Mounting
Button Descriptions
Reset -Press ‘Reset’button, to reset GSM
Signal Quality -Press ‘Signal Quality’button, to check the signal strength
Recover - Button reserved
REV -Button reserved
SignalstrengthCheck: Press ‘Signal Quality’button
No signal: 4 LEDs are off
Bad signal: only the Power LED is on
Weak signal: Power & Network LEDs are on
Good signal: Power, Network & Status LEDs are on
*
*

4
1 2 3 4 5 6
ON
DIP
DIP1-DIP5
Set ‘Off’ for House system (default)
Reserved
DIP6
DIP State Description
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
Set ‘On’ for Apartments system
3. DIP Switches Settingsfor GSM Interface
One GSM Interface needed for either house or Apartments systems
Touch ‘Call Divert’ icon or find ‘TPC’ icon in Installer Setup
4.Telephone Number Programming on Video Monitor
Exit&Unsave
Exit&save
-Telephone Number-
1> _
2> _
3> _
Don’t divert calls
Divert if not answered
Divert simultaneously
1 2 3
4 5 6
987
0
1. Maximum 3 telephone numbers can be
programmed
2. Touch the telephone number frame
3. Using the keypad, type in your number and
save it

5
Divert Modes
There are 3 types of divert modes:
• 1 - Do not divert calls. Calls from the door station wan’t be diverted
• 2 - Divert if not answered. If video monitor was not answered the call within 25
seconds, the call will be diverted to the telephone number you set.
In this mode, monitor will shut down when GSM diverts successfully.
The monitor still can do the operation of monitoring, talking and unlocking
• 3 - Divert simultaneously. Calls from the door station will be diverted to your
telephone immediately. In this mode, the monitor will rings with video, telephone
will ring as well. If monitor answers the call, GSM will stop diverting and telephone
will stop ringing

5.Operation Instructions
Function Description
Unlocking
• Input 1# on your telephone or mobile phone to
releasetherstlock
• Input 2# on you telephone or mobile phone to release
the second lock
Hanging up
• Input 9# on your telephone or mobile phone to hang
up
• Maximum time untill disconnection is 5 minutes
Calling next telephone
number
• 1: Second telephone number must be
programmed on monitor
• 2:If first number on the list did not answer the
call, GSM will dial next number
Calling extention
• Add a letter "P" between main telephone number and
extention telephone number and GSM will call the
extention telephone

6
GSM
Antenna
AC~
PC6
1 2
ON
ID=00
6.Wiring
7.Specications
Power input: DC 20~28Vdc (supplied by power supply)
Power Consumption: Standby:60mA;working:500mA
Working temperature: -10ºC +40ºC
Wiring: 2-wire, No-polarity
Dimension: 90(H)X72(W)X60(D)mm

The design and specications can be changed without notice to the user. Right to
interpret and copyright of this manual are preserved
www.intelligenthomeonline.com