Intellinet 525336 User manual

NANO 150N
WIRELESS
USB ADAPTER
USER MANUAL
MODEL 525336
INT-525336-UM-0212-01

CONTENTS
1 Introduction .............................................................................................................. 1
1.1 Features....................................................................................................................................1
1.2 Specifications............................................................................................................................1
2 Installation Procedure ..............................................................................................3
3 Configuration Utility ................................................................................................. 9
3.1 Utility Overview .........................................................................................................................9
3.2 Available Network ...................................................................................................................10
3.3 General ...................................................................................................................................11
3.4 Profile......................................................................................................................................12
3.4.1 Configure the Profile................................................................................. 13
3.5 Status......................................................................................................................................16
3.6 Statistics..................................................................................................................................16
3.7 Wi-Fi Protect Setup (WPS) .....................................................................................................17
3.8 Software AP ............................................................................................................................20
3.8.1 AP Properties Setting ............................................................................... 21
3.8.2 AP Advanced............................................................................................ 21
3.8.3 AP Statistics............................................................................................. 22
3.8.4 ICS .......................................................................................................... 22

1
1 Introduction
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™ Nano 150N Wireless USB
Adapter, Model 525336.By following the simple steps in this user manual, you will soon be able to
enjoy the helpful features listed below.
1.1 Features
• Connects your netbook, laptop or desktop PC to a wireless network
• Fits discretely into your netbook or laptop USB port
• Ideal for streaming HD-quality video, online gaming, downloading large files and making VoIP calls
• Low-profile design allows you to leave the adapter connected even when on the go
• High transfer data rate –up to 150 Mbps
• Complies with IEEE 802.11b/g and is upward compatible with 802.11n
• Supports WMM (Wi-Fi Multimedia) for increased multimedia data throughput
• Easily secure your network connection with Wi-Fi Protected Setup (WPS)
• Supports WEP (64/128 bit), WPA and WPA2 data encryption
• Supports the most popular operating systems: Windows XP, Vista and Windows 7
• Supports Hi-Speed USB 2.0/1.1 interface
• Supports Software AP function (turns your wireless client into a wireless access point)
• Three-Year Warranty
1.2 Specifications
Standards
• IEEE 802.11b (11 Mbps Wireless LAN)
• IEEE 802.11g (54 Mbps Wireless LAN)
• IEEE 802.11e (QoS Enhancement WMM)
• Upward compatible to IEEE 802.11n (150 Mbps Wireless LAN)
General
• Interface: Hi-Speed USB 2.0
• Chipset: Realtek RTL8188CUS
• Frequency band: 2.4000 –2.483 GHz (Industrial Scientific Medical Band)
• Modulation technologies:
-802.11b: Direct Sequence Spread Spectrum (DSSS): DBPSK, DQPSK, CCK
-802.11g: Orthogonal Frequency Division Multiplexing (OFDM): BPSK, QPSK, 16QAM, 64QAM
-802.11n: Orthogonal Frequency Division Multiplexing (OFDM): BPSK, QPSK, 16QAM, 64QAM
• Security:
-64/128-bit WEP data encryption
-WPA and WPA2
-Cisco CCX
• Transmit power:
-150 Mbps, 14 dBm +/-1.5 dBm
-54 Mbps, 15 dBm +/-1.5 dBm
-11 Mbps, 17 dBm +/-1.5 dBm
• Certification: FCC Class B, CE
LEDs
• Link/Activity
Environmental
• Dimensions: 7 (H) x 15 (W) x 17.4 (L) mm (0.27 x 0.6 x 0.66 in.)
• Weight: 0.14 kg (0.3 lbs.)
• Operating temperature: 0 –40°C (32 –104°F)
• Operating humidity: 10 –90% RH, non-condensing
• Storage temperature: -20 –60°C (-4 –149°F)

2
System Requirements
• Notebook or Desktop PC with Pentium 300 MHz-compatible processor or higher
• Windows XP, Vista and Windows 7
• Available Hi-Speed USB 2.0 port
Package Contents
• Nano 150N Wireless USB Adapter
• Quick install guide
• Setup CD with user manual

3
2 Installation Procedure
Before you proceed with the installation, note the following.
Note1: The following installation was operated under Windows XP. (Procedures are similar for
Windows 2000/Vista/7.)
Note2: If you have installed the Wireless PC Adapter driver and utility before, uninstall the old
version first.
I. Install the Driver and Utility
A. Insert the installation CD in your CD-ROM drive. Execute the “Setup.exe” program.
B. Select a setup language and click “OK” to proceed.
C. Click “Next” to go to the next step.

4
D. When you see the following screen, click “Install”to begin the installation.
E. The system starts to install the driver and utility.
F. Click “Finish” to complete the driver and utility installation.

5
II. Connect to a Wireless Access Point
A. To start configuring the adapter, double-click the icon in the system tray or right-click the icon and
select “Open configuration utility.”
B. The utility of the adapter is displayed. Click the “Available Network” tab and double-click on the
wireless access point you want to connect to.
C. Input the security setting and click “OK” to start the network connection.

6
* Use Windows Zero Configuration on Windows Vista / 7:
A. With Windows Vista / 7, you can use Windows Zero Configuration to connect to a wireless access
point.
Click “Start,” then click “Control Panel.”Click “Network and Internet”in the Control Panel.
B. Click “Connect to a network”under “Network and Sharing Center.”

7
C. Click the access point you want to use if it’s shown, then click “Connect.”
D. If it’s an unnamed access point (i.e.,the SSID of this wireless access point is hidden), you’ll be
prompted to input its name, and the name must be identical to the SSID setting of the wireless
access point you’re connecting to.

8
E. If the access point is protected by an encryption method, you need to input its security or
passphrase here. It must match the encryption setting on the access point.
F. If you can see the screen below, the connection between your computer and wireless access point
has been successfully established. Click “Close”to start the network connection.

9
3 Configuration Utility
The Configuration Utility is a powerful application that helps you configure the adapter and monitor the
link status and statistics during the communication process.
The Configuration Utility appears as an icon on the system tray and desktop of Windows. You can
open it by double-clicking the icon.
Right-click the icon in the system tray. There are some options for operating the configuration utility.
Open Config Utility
Select“OpenConfigUtility”toopentheconfigurationutility.
About
Select “About” to show the utility information.
Hide
Select “Hide” to hide the utility in the system tray.
Quit
Select “Quit” to quit the utility in the system tray.
IntheSystemTray IntheSystemTray(Right-click)
3.1 Utility Overview
There are several parts of the utility screen. Refer to the following table for the description.
A
B
C
D
E

10
Parameter
Description
Refresh – Refresh the adapter list in the “B“ block.
Mode – There are two modes: Station and Access Point. If
“Station“ is selected, the adapter works as a wireless adapter. If
“Access Point“ is selected, the adapter will works as a wireless
AP.
View – Enable “Status Bar“ and the “D“ block in the utility will
display the current status of the utility.
About – To check the version of the utility, select this item.
This is a list for you to configure several adapters in your PC from
the utility.
Show Tray Icon – To show the icon in the system tray, select the
item.
Disable Adapter – This is to disable or enable the adapter.
Windows Zero Config – To configure the adapter from Windows
XP Zero Configuration, check the item.
Radio Off – This is to turn off or turn on the radio of the adapter. If
the radio is turned off, the adapter will not work.
This is the status bar that displays the current status of the utility.
To close it, disable the “Status Bar“ in the “View“ item.
There are several tabs in the block for you to set up the functions
of the adapter. Refer to the descriptionsin the following sections.
3.2 Available Network
When you open the Configuration Utility, the system will scan all the channels to find all the access
points/stations within the accessible range of your adapter and automatically connect to the wireless
network with the highest signal strength. From the “Available Network” tab, all the networks nearby will
be listed. You can change the connection to another network.
A
B
C
D
E

11
Parameter
Description
Available Network(s)
This list shows all information of the available wireless networks
within the range of your adapter (SSID, Channel, Encryption,
Network Authentication, Signal etc.). To connect to any network
on the list, double-click the selected network.
Refresh
Click “Refresh“ to update the available networks list. It is
recommended that you refresh the list any time you have changed
the connection network.
Add to Profile
A profile stores the settings of a network so that you can connect
to the network quickly. To add the selected network to a profile,
click this button.
3.3 General
To check the connection status of the adapter, select “General.” This screen shows the Link Speed,
Network Type, Encryption Method, SSID, Signal Strength, Link Quality and Network Address of the
adapter.
Parameter
Description
Status
This showsthe connection status of the adapter.
Speed
This shows the current speed.
Type
Infrastructure – This operation mode indicates the presence of
an 802.11 access point. All communication is done via the access
point or router.
IBSS – This displays if you decided to connect to other wireless
stations in the wireless LAN network without going through an
access point or router.

12
Encryption
This displays the encryption setting of the current connection:
None, WEP, TKIP or AES.
SSID
The SSID (up to 32 printable ASCII characters) is the unique
name identified in a WLAN. The ID prevents the unintentional
merging of two co-located WLANs.
Signal Strength
This indicates the wireless signal strength.
Link Quality
This indicates the wireless link quality.
Network Address
This shows the MAC, IP address and other information about the
adapter.
3.4 Profile
The “Profiles List” is for managing the networks you connect to frequently. You are able to use
Add/Remove/Edit/Duplicate/Set Default to manage a profile.
Parameter
Description
Available Profile(s)
This list shows the preferred networks for the wireless connection.
You can add, remove, edit and duplicate the preferred networks or
set one of the networks as the default connection.
Add/ Remove/ Edit
Click these buttons to add/ delete/ edit the selected profiles.
Duplicate
To build up the new profile with the same settings as the current
profile, select this feature.
Set Default
To designate a profile as the default network for the connection
from the available profiles list, click this button.

13
3.4.1 Configure the Profile
Parameter
Description
Profile Name
Define a recognizable profile name so you can identify different
networks.
Network Name (SSID)
The SSID (up to 32 printable ASCII characters) is the unique
name identified in a WLAN. The ID prevents the unintentional
merging of two co-located WLANs.
You may specify anSSID for the adapter and then only the device
with the same SSID can interconnect with the adapter.
This is a computer-to-computer
(ad hoc) network; wireless access
points are not used.
There are two kinds of network type:
Infrastructure – This operation mode requires the presence of an
802.11 access point. All communication is done via the access
point or router.
Ad Hoc – Connect to another wireless adapter in the wireless
LAN network without going through an access point or router.
If this is selected, the adapter will work in Ad Hoc mode.
Channel
This setting is only available for Ad Hoc mode. Select the radio
channel used for the networking. The channel setting should be
the same as the network you are connecting to.
Network Authentication
This setting has to be consistent with the wireless networks that
the adapter intends to connect.
Open System – No authentication is needed within the wireless
network.
Shared Key –Only wireless stations using a shared key (WEP
Key identified) are allowed to connect to each other.
WPA-PSK – This is a special mode designed for home and small

14
business users who do not have access to network authentication
servers. In this mode, known as Pre-Shared Key, the user
manually enters the starting password in their access point or
gateway, as well as in each wireless station in the network.
WPA-PSK takes over automatically from that point, keeping
unauthorized users that don’t have the matching password from
joining the network, while encrypting the data traveling between
authorized devices.
WPA2-PSK – WPA2-PSK is also for home and small business.
The difference between WPA-PSK and WPA2-PSK is that
WPA2-PSK provides data encryption via AES. In contrast,
WPA-PSK uses the Temporal Key Integrity Protocol (TKIP).
WPA 802.1X – WPA provides a scheme of mutual authentication
using either IEEE 802.1x / Extensible Authentication Protocol
(EAP) authentication or pre-shared key (PSK) technology. It
provides a high level of assurance to enterprises, small
businesses and home users that data will remain protected and
that only authorized users may access their networks. For
enterprises that have already deployed IEEE 802.1x
authentication, WPA offers the advantage of leveraging existing
authentication databases and infrastructures.
WPA2 802.1X –Like WPA, WPA2 supports IEEE 802.1x / EAP
authentication or PSK technology. It also includes a new
advanced encryption mechanism using the Advanced Encryption
Standard (AES). AES is required for corporate or government
users. The difference between WPA and WPA2 is that
WPA2 provides data encryption via AES. In contrast, WPA uses
the Temporal Key Integrity Protocol (TKIP).
WEP 802.1X – This is a special mode for using IEEE 802.1x /
EAP technology for authentication and WEP keys for data
encryption.
Data Encryption
Disabled – Disable the WEP Data Encryption.
WEP – Enable the WEP Data Encryption. When this is selected,
you need to continue setting the WEP Encryption keys.
TKIP – TKIP (Temporal Key Integrity Protocol) changes the
temporal key every 10,000 packets (a packet is a kind of message
transmitted over a network). This ensures much greater security
than the standard WEP security.
AES – AES has been developed to ensure the highest degree of
security and authenticity for digital information,and it is the most
advanced solution defined by IEEE 802.11i for security in the
wireless network.
NOTE: All devices in the network should use the same
encryption method to ensure proper communication.

15
ASCII
The WEP key can be in ASCII format (alphanumeric values or
signs are allowed) so it’s more recognizable for users.
PASSPHRASE
This is a text string with a maximum of 32 alphanumeric
characters; for example, “Test.” The WEP key is based on the
passphrase determined by you. This passphrase may not work
with other vendors’ products due to possible incompatibility with
other vendors’ passphrase generators, so you must use the same
passphrase or WEP key settings for all wireless computers within
the network.
Key Length
When you select “WEP and “PASSPHRASE,“ this function will
display in the current status of the utility. The keys are used to
encrypt data transmitted in the wireless network. Fill the text box
by following the rules below.
64-bit – Input 10-digit hex values as the encryption keys. For
example: “0123456aef.“
128-bit – Input 26-digit hex values as the encryption keys. For
example: “01234567890123456789abcdef.“
Key Index (advanced)
Select one of the four keys to be the data encryption key.
Network Key
Enter the network security key ensure the password is correct.
Confirm Network Key
Enter the network security key again.
EAP Type
GTC – GTC is an authentication protocol that allows the exchange
of clear text authentication credentials across the network.
TLS – TLS is the most secure of the EAP protocols,but is not
easy to use. It requires that digital certificates be exchanged in the
authentication phase. The server presents a certificate to the
client. After validating the server’s certificate, the client presents a
client certificate to the server for validation.
LEAP – LEAP is a pre-EAP, Cisco-proprietary protocol with many
of the features of EAP protocols. Cisco controls the ability of other
vendors to implement this protocol, so it should be selected for
use only when limited vendor choice for client, access-point and
server products is not a concern. When you have set up LEAP
authentication, you need to enter the user name and password of
your computer.
PEAP & TTLS – PEAP and TTLS are similar and easier than TLS
in that they specify that a stand-alone authentication protocol be
used within an encrypted tunnel. TTLS supports any protocol
within its tunnel, including CHAP, MSCHAP, MSCHAPv2 and
PAP. PEAP specifies that an EAP-compliant authentication
protocol must be used; this adapter supports MD5, TLS, GTC
(Generic Token Card) and MSCHAPv2.
Tunnel
Includes MD5, GTC, TLS, MSCHAP-v2.
Username
The certificate username in the RADIUS server.
Identity
User’s identity in the RADIUS server.

16
Password
User’s password in the RADIUS server.
Certificate
Select the certificate for RADIUS server authentication.
3.5 Status
This screen shows information about the manufacturer, driver version, settings of the wireless network
the adapter is connecting to, linking time and link status. If you’re unsure about the status of the
adapter and the network you are connecting, go to the screen for more details.
3.6 Statistics
You can get real-time information about the packet transmission and receiving status during wireless
communication from this screen. To recount the statistics value, click “Reset.“

17
3.7 Wi-Fi Protect Setup (WPS)
Wi-Fi Protected Setup (WPS) is the latest wireless network technology,which makes wireless network
setup become very simple. If you have a WPS-enabled wireless access point and you want to establish
a secure connection to it, you don’t need to configure the wireless access point and set up data
encryption by yourself. All you need to do is to go to the WPS setup page of this wireless card, click the
PBC or PIN button, and then press a WPS button or enter an 8-digit code on the wireless access point
you want to establish a secure connection to.
I. Pin Input Config (PIN)
1. The PIN code of your wireless network card is an 8-digit number located at the upper-right
position of configuration utility. Remember it, and input the number to your wireless access
point as the WPS PIN code. (Refer to the user manual of your wireless access point for
instructions about how to do this.)
2. Click “Pin Input Config (PIN)”and the following message will appear on your computer.
Click “Yes”to select a specific wireless access point or click “No” to start PIN method of
WPS.

18
3. If you click “Yes”and the following message appears on your computer, select the SSID of
the wireless access point that you want to connect to and click “Select.”
4. You’ll need to wait up to two minutes while the install procedure runs. If a wireless access
point with the correct PIN code is found, you’ll be connected to that access point.