Intellinet 561099 User manual




8‐PORTGIGABITWEB‐SMARTSWITCH
USERMANUAL
Model561099

















8‐PortGigabitWeb‐SmartSwitch
2|Page


FCCCertifications
ThisEquipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB
digitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedto
providereasonableprotectionagainstharmfulinterferencewhentheequipment
isoperatedinacommercialenvironment.Thisequipmentgenerates,uses,and
canradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordance
withtheinstructionmanual,maycauseharmfulinterferencetoradiocommunications.

Operationofthisequipmentinaresidentialareaislikelytocauseharmfulinterferenceinwhichcasethe
userwillberequiredtocorrecttheinterferenceathisownexpense.

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:
(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterference
received;includinginterferencethatmaycauseundesiredoperation.



CEMarkWarning
ThisequipmentcomplieswiththerequirementsrelatingtotheEMCDirective
2004/108/ECand2014/30/EU,theLowVoltageDirective2006/95/ECand
2014/35/EU,andtheRoHSDirective2011/65/EU. 

Intellinethasanon‐goingpolicyofupgradingitsproductsanditmaybe
possiblethatinformationinthisdocumentisnotup‐to‐date.Pleasecheckwithyourlocaldistributorsfor
thelatestinformation.Nopartofthisdocumentcanbecopiedorreproducedinanyformwithoutwritten
consentfromthecompany.

Trademarks:
Alltradenamesandtrademarksarethepropertiesoftheirrespectivecompanies.
Copyright©2015Intellinet,AllRightsReserved.





8‐PortGigabitWeb‐SmartSwitch
3|Page

1 Contents
2Introduction ···················································································· 5
2.1General Description ···································································· 5
2.2Key Features ············································································ 5
2.3The Front Panel ········································································· 6
2.4The Rear Panel ········································································· 6
2.5Hardware Installation ·································································· 7
2.6Connect to Web Admin Interface ··················································· 7
3System Configuration ······································································· 8
3.1Management ············································································· 8
3.1.1Switch Information ·································································· 8
3.1.2IP Address Settings ································································ 9
3.1.3Port Setting ··········································································· 9
3.1.4Trunk Group Settings ····························································· 11
3.1.5EEE – Energy Efficient Ethernet ·············································· 12
3.2Maintenance ··········································································· 13
3.2.1User Account ······································································· 13
3.2.2Firmware Upgrade ································································ 14
3.2.3Config Backup and Restore ···················································· 16
3.2.4Reset to Default Config ·························································· 17
3.2.5Config Save ········································································ 18
3.2.6Reboot ··············································································· 18
3.3MultiCast ················································································ 19
3.3.1IGMP Snooping ··································································· 19
4Monitoring ··················································································· 20
4.1Port Statistics ·········································································· 20
4.2Diagnostic ·············································································· 21
4.3Port Mirroring ·········································································· 22
5VLAN ························································································· 23
5.1VLAN Mode Setting ·································································· 24
5.2Port Based VLAN ····································································· 24
5.3MTU VLAN ············································································· 26
5.4802.1Q VLAN ·········································································· 27
5.4.1802.1Q Static VLAN ······························································ 27
5.4.2802.1Q VLAN Port ································································ 28
6QoS ··························································································· 30
6.1Port-based Priority ··································································· 30
6.2Bandwidth Control ···································································· 32
7Security ······················································································ 33

8‐PortGigabitWeb‐SmartSwitch
4|Page

7.1Storm Filter ············································································· 33
7.2Loop Prevention ······································································ 34
7.3DHCP Snooping ······································································ 35
8Appendix A: Changing the IP Address of a Network Adapter ·················· 36
8.1Windows 8 ·············································································· 36
8.2Windows 7 and 10 ···································································· 39
8.3Windows XP: ·········································································· 40
8.4Mac OS X ··············································································· 41
9Warranty ····················································································· 42
10Copyright ···················································································· 43
11Federal Communication Commission Interference Statement ················· 44



8‐PortGigabitWeb‐SmartSwitch
5|Page

2 Introduction
2.1 GeneralDescription
Thedeviceisahigh‐performanceGigabitEthernetswitch,withall8portscapableof10/100/1000Mbps
auto‐negotiationoperation(NWay)whichmeanstheswitchcouldautomaticallynegotiatewiththe
connectedpartnersonthenetworkspeedandduplexmode.
ThisswitchsupportstheWebGUItocontroleachportstatusandbandwidthcontrolbyportratelimiting.
It’seasytosettheVLAN&QoSfunctions,theVLANincludesMTUVLAN,PortBaseVLAN&802.1QVLAN.
TheQoShas4priorityqueueswhichcansettheStormFilterforBroadcastStorm,MulticastStorm&
UnicastStorm.Loopdetectionandpreventionfunctionsaresupportedfordetecting/resolvingthecable
loopbackconnectionissuemoreeasily.SupportsDHCPSnoopingfunctiontopreventun‐trustedDHCP
serverinstalledforeasilymaintainingnetworkmanagement.
TheswitchcomplieswithIEEE802.3azEnergyEfficientEthernettosavepowerconsumption,andsupports
IGMPSnoopingtoimprovetrafficperformance.Moreover,therichdiagnosticLEDsonthefront‐panel
providetheoperatingstatusofindividualportsandthewholesystem.

2.2 KeyFeatures
 8xRJ‐45portsfor10/100/1000Mbpsconnectivity
 AllRJ45portswithAuto‐MDIX(autouplink)support
 Supports802.3xflowcontrolforfullduplexmodeandcollision‐basedbackpressureforhalfduplex
mode
 ComplieswithIEEE802.3azEnergyEfficientEthernet
 SupportsEEEenableanddisable
 SupportsIEEE802.3xFlowControl
 Supportsstormfilter(Broadcast,Multicast,Unicast)
 TheQoSsupports802.1pQoSandportratelimiting
 TheVLANincludesMTU,Port‐based&802.1QTagBased
 Supports4groupsofport‐basedVLAN
 Providesporttrunk,onegroupwithtwomemberports 
 Providesportmirroring
 SupportsIGMPsnoopingv1/v2/v3
 Supportsloopdetectionandprevention
 Providescabletestingfunction
 SupportsDHCPclient
 SupportsDHCPsnooping
 FirmwareupdateviaHTTPandTFTP
 Supportsconfigurationbackup&restore
 Supportsresettofactorydefaultbutton

8‐PortGigabitWeb‐SmartSwitch
6|Page

2.3 TheFrontPanel



LEDsDefinition
ThisdeviceprovidesextensiveLEDstoshowtheactivitiesonpower,systemandports.
Seethefollowingdescriptionforyourreference:

LED Status Operation
POWER SteadyGreen Thedevice ispoweredon.
Off Thedeviceispoweredoff.
LOOP SteadyRed Thedevicehasdetectedalooponthenetwork.
Off Noloophasbeendetected.
Link/ACT
SteadyGreen Alinkhasbeenestablishedtothedeviceconnectedtothisport..
BlinkingGreen Dataistransmittedoverthisport.
Off TheportisnotconnectedtoanactiveRJ45Ethernetdevice.

TheResetButton
ResettheswitchtoitsfactorydefaultconfigurationviatheRESETbutton.PresstheRESETbuttonformore
thanfivesecondstoenableresettodefaultfunction.Theswitchautomaticallyrebootsandreloadsits
factoryconfigurationfile.

2.4 TheRearPanel
Thefollowingfigureshowstherearpaneloftheswitch:



PowerconnectorandRJ45Ethernetportsarelocatedontherearpanelofthe8‐PortGigabitWeb‐Smart
Switch.StandardCat5eorCat6RJ45Ethernetcableissupported,includingstraight‐throughandcrossover
variants.


8‐PortGigabitWeb‐SmartSwitch
7|Page

2.5 HardwareInstallation
DesktopInstallation
Placetheswitchonaflatsurface.Ensureadequateventilationspacearoundtheswitchfordissipating
heatandair.Properlyconnectthedevicetoapoweroutletusingtheincludedpowercable,anditwill
automaticallyinitializeandthepowerLEDwilllightup.

InstallingNetworkCables
Tomakeavalidconnectionandobtaintheoptimalperformance,anappropriatenetworkcablethat
correspondstodifferenttransmitting/receivingspeedsisrequired.Tochooseasuitablecable,pleaserefer
tothefollowingtable.

Media Speed Wiring
NetworkMedia
(Cable)
10Mbps 10Base‐T:UTPcategory3,4,5cable(maximum100m)EIA/TIA‐568
100ΩSTP(maximum100m) 
100Mbps 100Base‐TX:UTPcategory5,5ecable(maximum100m)EIA/TIA‐568
100ΩSTP(maximum100m)
1000Mbps 1000Base‐T:UTPcategory5e,6cable(maximum100m)EIA/TIA‐568
100ΩSTP(maximum100m)

2.6 ConnecttoWebAdminInterface
InordertoconfigurethesmartfeaturesoftheIntellinet8‐PortGigabitWeb‐SmartSwitch,youneedtoset
theIPaddressofyourcomputer’snetworkadaptertoavalueof192.168.2.xxxwherexxxmustnotbe
equalto1.RefertoAppendixAfordetails.

ThedefaultIPoftheIntellinet8‐PortGigabitWeb‐SmartSwitchis192.168.2.1.Open“http://192.168.2.1”
inyourwebbrowser.


Theloginscreenappears. 
UserName:‘admin’
Password:‘1234’




8‐PortGigabitWeb‐SmartSwitch
8|Page

3 SystemConfiguration

3.1 Management
3.1.1 SwitchInformation
ThispagedisplayssomecoreinformationabouttheIntellinet
8‐PortGigabitWeb‐SmartSwitch.Theinformationisread‐
only,exceptfortheswitchname,whichyoucanedit. 











Note:

Inordertosaveanychangesyoumaketotheprogrammingofthe
Intellinet8‐PortGigabitWeb‐SmartSwitch,youaregoingtohave
toclickon . 





8‐PortGigabitWeb‐SmartSwitch
9|Page

3.1.2 IPAddressSettings


LABEL DESCRIPTION
DHCPClient
EnableordisabletheDHCPClientfunction.
Ifthisisenabled,theIntellinetswitchreceivesitsIPsettings(IPAddress,
SubnetMaskandGateway)fromaDHCPserverinyourLAN,i.e.arouter.
Ifsetto‘disable’,thenyoumustprovidetheIPinformationyourselfandenter
themintothefieldbelow. 
IPAddress SystemIPaddressoftheswitch.Thedefaultvalue192.168.2.1.
SubnetMask Subnetmaskoftheswitch.Thedefaultvalueis255.255.255.0.
Gateway GatewayIPaddressoftheswitch.
Apply ClickApplytosaveandactivatethesettings.


3.1.3 PortSetting
OnthispageyoucancontrolsomebasicparametersfortheRJ45portsontheIntellinet8‐PortGigabit
Web‐SmartSwitch. 


LABEL  DESCRIPTION 
Port  Selecttheportwhichyouwishtoconfigurefromthelistbox. 
State AllowsyoutoEnable/Disabletheport.
Speed/Duplex Auto:EnablesmaximumGigabitfullduplexperformance
10M/Half:10Mbps,half‐duplex
10M/Full:10Mbps,full‐duplex 
100M/Half:100Mbps,half‐duplex
100M/Full:100Mbps,full‐duplex
FlowControl  Enableordisabletheflowcontrolabilityoftheselectedports.
Apply  ClickApplytosavethesettingsandactivatethem.

8‐PortGigabitWeb‐SmartSwitch
10|Page



Port Displaystheportnumber.
State Displaystheactualstateoftheport.
Speed/Duplex Config:Displaystheconfigurationoflinkspeedandduplexmodefortheport.
Actual:Displaystheactualworkingstateoftheport.
FlowControl Config:Displaystheconfigurationoftheflowcontrolfortheport.
Actual:Displaystheactualworkingstateoftheport.



Note:
Theswitchcan’tbemanagedthroughadisabledport.Besurenottodisabletheportthroughwhichyou
areconnectingtotheswitch. 




8‐PortGigabitWeb‐SmartSwitch
11|Page

3.1.4 TrunkGroupSettings
TocreatealinkbetweentheIntellinet8‐PortGigabitWeb‐SmartSwitch,younormallysimplyconnectan
RJ45Ethernetcabletoaportonadifferentswitch.IfthatisalsoaGigabitswitch,thisconnectionbetween
thetwoswitcheswouldprovideabandwidthof1Gbps.Inordertoincreasethebandwidth,youcanset
upasocalledtrunkinggroup,whichtakestwophysicalportsandcombinesthemtoonelogicport,
doublingthebandwidthto2Gbps.


1. Selectanytwoportsofportsonetofour.
2. ClickAdd/Modifytocreatethetrunkgroup



Note:
Whenusingtrunkgroups,thefollowingrestrictionsapply:

 Youmayonlycreateonetrunkinggroup.
 Onlytwoportscanformatrunkinggroup,andonlyports1–4canbeamemberofatrunking
group.
 Allmemberportsofatrunkgroupmusthaveidenticalport&QoSsettings.
 Allmemberportsofatrunkgroupmusthavethesameport‐basedpriority.
 Allmemberportsofatrunkgroupmusthavethesame802.1QVLANportsetting.
 Allmemberportsofatrunkgroupmusthavethesamestormfilterrate.
 Allmemberportsofatrunkgroupmusthavethesameframetype.
 TheGigabitswitchontheoppositeendmustalsobeconfiguredwithatrunkinggroupconsisting
oftwoports.



  8‐PortGigabitWeb‐SmartSwitch
12|Page

3.1.5 EEE–EnergyEfficientEthernet
Energy‐EfficientEthernet(EEE)isasetofenhancementstothetwisted‐pair
andbackplaneEthernetfamilyofcomputernetworkingstandardsthatallow
forlesspowerconsumptionduringperiodsoflowdataactivity.Theintention
wastoreducepowerconsumptionby50%ormore,whileretainingfull
compatibilitywithexistingequipment.TheInstituteofElectricalandElectronicsEngineers(IEEE),through
theIEEE802.3aztaskforcedevelopedthestandard.EEEisapowersavingoptionthatreducesthepower
usagewhenthereislowornotrafficutilization.EEEworksbypoweringdowncircuitswhenthereisno
traffic. 

Whenaportispowereddownforsavingpower,theoutgoingtrafficisstoredinabufferuntiltheportis
poweredupagain.Usingthistechnique,morepowercanbesavedifthetrafficcanbebufferedupuntila
largeburstoftrafficcanbetransmitted.Keepinmind,thatbufferingtrafficwilladdsomelatencyinthe
traffic.

IfEEEisnotdesiredinyournetworkenvironment,youcandisablethisfeatureonthisscreen.





8‐PortGigabitWeb‐SmartSwitch
13|Page

3.2 Maintenance
3.2.1 UserAccount
Onthisscreenyoucanchangetheusernameandpasswordrequiredtoaccessthewebadministrator
configurationmenu. 


Enteranewusernameandpassword,thenclickApply.Youwillthenhavetoenterthenewusernameand
passwordinordertologbackintotheconfiguration. 




Note:
Onlydigitsandregularalphanumericcharacterscanbeusedforcreatingtheusernameandpassword.
Donotuseanyspecialcharacters.Thelengthoftheusernameshouldnotbemorethan20characters
andthepasswordshouldnotbelongerthan17characters. 



8‐PortGigabitWeb‐SmartSwitch
14|Page

3.2.2 FirmwareUpgrade   
Ifanewfirmwareneedstobeinstalled,youcanusethisscreentodoit.Youcaninstallanewfirmware
image(file)usingTFTP,orHTTP.Inordertobegintheprocess,youmustfirstentertheso‐calledloader
mode.





AfteryouclickOK,youwillseeanewmenuontheleftsideofthescreen.Thismenuprovidesaccessto
theTFTPandHTTPmethodofupdatingthefirmware.


TFTP
ToinstalltheupgradeviaTFTP,aTFTPservermustbeconfiguredtoacceptconnectionsfromtheIntellinet 
switch.ProvidetheIPaddressoftheTFTPserveralongwiththecorrectfilenamethatyouwishtoinstall.

EntertheImageFileNameandclickDownloadImage,thenamessagewillpopup.







  8‐PortGigabitWeb‐SmartSwitch
15|Page


ClickOKandallowtheproceduretocomplete.Theswitchwillperformarestartattheendofthe
firmwareupgradeprocedure.






HTTP
Inordertoinstalltheupgrade,selecttheappropriateupgradetype,thenclickon ,selectthefile
fromyourlocalHDD.Thenpress  tobegin.


ClickUpgrade,thenamessagewillpopup.


ClickOKandallowtheproceduretocomplete.Theswitchwillperformarestartattheendofthe
firmwareupgradeprocedure.




Inordertoleavetheloadermodeandreturntothestandardoperationmode,clickon‘Reboot.’



8‐PortGigabitWeb‐SmartSwitch
16|Page

3.2.3 ConfigBackupandRestore
OnthispageyoucansavetheentireconfigurationoftheIntellinet8‐PortGigabitWeb‐SmartSwitchtoa
file,soyoucanre‐load(restore)itatalatertime.

Clickon  tobegin.Thenselect  andclick . 
Thenselectthelocationwhereyouwishtosavethefile,andclick .



Inordertorestoreapreviouslysavedconfiguration,youhavetoselecttheconfigurationfileusingthe
 button,andthenclickon .




8‐PortGigabitWeb‐SmartSwitch
17|Page


3.2.4 ResettoDefaultConfig
TherearetwowaystoresettheIntellinetswitchbacktoitsfactorydefaultsettings.

ViaResetButton
Presstheresetbuttonforatleast10secondswhiletheswitchisoperationinordertotriggerthefactory
defaultreset.





ViaWebAdministratorMenu
Clickon ,thenprovideadministratorcredentialsandclick‘OK’tobegin.







  8‐PortGigabitWeb‐SmartSwitch
18|Page

3.2.5 ConfigSave 
InordertosaveanychangesyoumaketotheprogrammingoftheIntellinetGigabitswitch,youaregoing
tohavetoclickon .Oncedone,themessagebelowconfirmsthatallsettingshavebeen
saved.



3.2.6 Reboot
IfyouneedtoreboottheIntellinetswitchfromaremotelocation,thisisthewaytodoit.Whenthe
rebootistriggered,theswitchwon’tbeaccessibleandoperationalforabout60seconds.



Thefollowingmessagewillremindyouthatanysettingsnotyetsavedintotheconfiguration(seeprevious
section)willbelost,sobesuretoclickon  first.



  8‐PortGigabitWeb‐SmartSwitch
19|Page


3.3 MultiCast
3.3.1 IGMPSnooping
TheInternetGroupManagementProtocol(IGMP)letshostsandroutersshareinformationabout
multicastgroupmemberships.IGMPsnoopingisaswitchfeaturethatmonitorstheexchangeofIGMP
messagesandcopiesthemtotheCPUforfutureprocessing.TheoverallpurposeofIGMPSnoopingisto
limittheforwardingofmulticastframestoonlyportsthatareamemberofthemulticastgroup.

AbouttheInternetGroupManagementProtocol(IGMP)Snooping
Computersandnetworkdevicesthatwanttoreceivemulticasttransmissionsneedtoinformnearby
routersthattheywillbecomemembersofamulticastgroup.TheInternetGroupManagementProtocol
(IGMP)isusedtocommunicatethisinformation.IGMPisalsousedtoperiodicallycheckthemulticast
groupformembersthatarenolongeractive.Inthecasewherethereismorethanonemulticastrouter
onasubnetwork,onerouteriselectedasthe‘queried’.Thisrouterthenkeepstrackofthemembership
ofthemulticastgroupsthathaveactivemembers.TheinformationreceivedfromIGMPisthenusedto
determineifmulticastpacketsshouldbeforwardedtoagivensubnetworkornot.Theroutercancheck,
usingIGMP,toseeifthereisatleastonememberofamulticastgrouponagivensubnetwork.Ifthereare
nomembersonasubnetwork,packetswillnotbeforwardedtothatsubnetwork.

MulticastService


YoucanenableordisableIGMPSnoopingonthisscreen.



8‐PortGigabitWeb‐SmartSwitch
20|Page

4 Monitoring
4.1 PortStatistics
ThesepagesprovidesstatisticaldataaboutthenetworkportsoftheIntellinetswitch. 




LABEL  DESCRIPTION 
Port  Displaystheportnumberoftheswitch.
State Displayswhethertheportisenabledordisabled.
LinkStatus  Displaysthelinkstateoftheport. 
TxGoodPkt Displaysthenumberofgoodpacketstransmittedontheport. 
TxBadPkt Displaysthenumberoferrorpacketstransmittedontheport. 
RxGoodPkt Displaysthenumberofgoodpacketsreceivedontheport. 
RxBadPkt Displaysthenumberoferrorpacketsreceivedontheport.
Clear Clicktoresettheportstatisticdata.





