Intellinet IPS-6GM02-60W User manual

PoE-Powered 6-Port Lite Smart
Managed PoE+ Switch with 4 GbE
Ports / 2 GbE Uplinks and PoE
Passthrough
User Manual
Model 562034 (IPS-6GM02-60W)
intellinet-network.com

2
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
All trademarks and trade names are the property of their respective owners. © IC Intracom. All rights
reserved. Intellinet Network Solutions is a trademark of IC Intracom, registered in the U.S. and other
countries.
No part of this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying or scanning, for any purpose other than the personal use by the
purchaser of this product. IC Intracom assumes no responsibility for any errors that may appear in this
document.
Whereas reasonable eort has been made to make the information in this document as useful and accurate
aspossible. IC Intracom assumes no responsibility for the application, usefulness, or completeness of the
informationcontained herein. Under no circumstance will IC Intracom be responsible or liable for any
damages or losses includingdirect, indirect, special, incidental, or consequential damages or losses arising
from either the use of any information contained within this manual or the use of any products or services
referenced in this manual.
IC Intracom reserves the right to change any product’s features, specications, documentation, warranties,
fee schedules, and conditions at any time and without notice.
This manual provides information about using Intellinet Network Solutions PoE-Powered 6-Port Lite Smart
Managed PoE+ Switch with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough [562034 / IPS-6GM02-60W]
READER OBJECT
• Network Engineer
• Technical Promotion Personnel
• Network Administrator
TECHNICAL SUPPORT
Intellinet Website intellinet-network.com
MANUAL DETAILS
Command line format Convention
The meaning of the command line format is explained below:
Bold: the command line keywords (the parts that must be input as they remain unchanged in the command)
areexpressed in bold font.
Italics: command line parameters (parts of the command that must be replaced by actual values) are
expressed in italics.
[ ]: indicates the part enclosed by [ ], which is optional during command conguration.
{ x | y | ... }: Indicates that one of two or more options is selected.
[ x | y | ... ]: Indicates to select one or none of two or more options.
//: a line starting with a double slash is represented as a comment line.
Description
• Some port types illustrated in this manual may be inconsistent with the actual situation. In actual
operation, it is necessary to congure according to the port types supported by each product.
• The display information illustrated in this manual may contain the contents of other product series (such
as product model, description, etc.), and the specic display information shall be subject to the actual
equipment information.

3
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
TABLE OF CONTENTS
INTRODUCTION .........................................................................................................................................5
PRODUCT OVERVIEW ..............................................................................................................................5
FEATURES.................................................................................................................................................5
EXTERNAL COMPONENT DESCRIPTION...................................................................................................6
FRONT PANEL ......................................................................................................................................6
REAR PANEL .........................................................................................................................................6
PACKAGE CONTENTS..............................................................................................................................6
INSTALLING THE SWITCH ............................................................................................................................7
DESKTOP INSTALLATION .........................................................................................................................7
WALL MOUNTING....................................................................................................................................7
CONFIGURATION GUIDE............................................................................................................................8
CONNECTING TO POWER .......................................................................................................................8
CONNECTING TO POWER .......................................................................................................................8
LOGGING INTO THE SWITCH......................................................................................................................9
WEB SMART CONFIGURATION .................................................................................................................12
HOMEPAGE ...........................................................................................................................................12
SYSTEM SETTINGS..................................................................................................................................12
DEVICE INFO ......................................................................................................................................12
IP SETTINGS........................................................................................................................................12
WEB SETTINGS....................................................................................................................................13
TELNET SETTINGS ................................................................................................................................13
USER MANAGEMENT ..........................................................................................................................13
UPGRADE ...........................................................................................................................................13
MONITORING........................................................................................................................................14
PORT STATISTICS ................................................................................................................................14
CABLE DIAGNOSTICS.........................................................................................................................14
LOOP GUARD (PART OF OUR SELF-HEALING NETWORK SUITE) ..........................................................14
IGMP SNOOPING...............................................................................................................................15
SWITCH SETTINGS .................................................................................................................................15
PORT SETTINGS ..................................................................................................................................15
PORT MONITORING ...........................................................................................................................15
PORT ISOLATION ................................................................................................................................16
JUMBO FRAME...................................................................................................................................16
GREEN ENABLE...................................................................................................................................16
STATIC MAC .......................................................................................................................................16

4
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
FILTER MAC ........................................................................................................................................17
SEARCH MAC.....................................................................................................................................17
MAC LIST............................................................................................................................................17
DHCP SNOOPING ..............................................................................................................................17
VLAN SETTINGS .....................................................................................................................................18
VLAN MEMBER ...................................................................................................................................18
VLAN SETTINGS ..................................................................................................................................18
QOS SETTINGS ......................................................................................................................................19
PORT RATE..........................................................................................................................................19
STORM CONTROL...............................................................................................................................19
QOS (QUALITY OF SERVICE) PROPERTY.............................................................................................20
COS PRIORITY MAPPING ...................................................................................................................20
DSCP PRIORITY MAPPING..................................................................................................................20
INNER PRIORITY MAPPING.................................................................................................................21
QUEUE SCHEDULING..........................................................................................................................21
POE SETTINGS .......................................................................................................................................22
POE GLOBAL INFO .............................................................................................................................22
POE BASIC SETTINGS .........................................................................................................................22
PDM (POWERED DEVICE MONITOR) A POE WATCHDOG FEATURE .......................................................23
ONVIF (OPEN NETWORK VIDEO INTERFACE FORUM) ............................................................................23
APPENDIX: TECHNICAL SPECIFICATIONS ..............................................................................................24

5
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
INTRODUCTION
Thank you for purchasing the Intellinet Network Solutions PoE-Powered 6-Port Lite Smart Managed PoE+
Switch with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough. Before you install and use this product, read
this manual carefully for a full understanding of its functions.
PRODUCT OVERVIEW
This Web Smart Managed PoE Switch features 6 RJ45 ports with speeds of 10/100/1000Mbps. Each port
supports automatic MDI/MDIX rollover and wire-speed forwarding. Ports 1-4 oer PoE power supply per
IEEE 802.3af/at standards, serving as power sources for compatible devices. The switch utilizes storage and
forwarding technology with dynamic memory allocation to eectively allocate bandwidth to each port. It
oers user-friendly interface, enabling exible expansion of home and oce networks without being limited
by power line layouts. It’s easy to manage and maintain, adapting to diverse scenario requirements.
Web Smart refers to the device web management system, that is, the web management system that
manages or congures the device, and manages the device by accessing Web Smart using a browser (such
as Chrome).
Web management includes two parts: Web server and Web client. The Web server is integrated on the device
to receive and process the requests sent by the client and return the processing results to the client. The Web
client usually refers to the browser, such as Chrome, IE and FF.
FEATURES
• Supports IEEE 802.3, IEEE802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3p, IEEE 802.3q, IEEE 802.3u, IEEE
802.3x, IEEE 802.3z.
• Power budget of 60 W.
• Supports PoE power up to 30 W for each PoE port.
• Supports MAC address auto-learning and auto-aging.
• Six 10/100/1000 Mbps self-adapting RJ45 ports
• Six gigabit RJ45 ports to link to higher-bandwidth equipment upstream.
• Store and forward switching architecture.
• Web-based management support.
• LED indicators for monitoring power, link/activity and PoE.

6
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
EXTERNAL COMPONENT DESCRIPTION
FRONT PANEL
The front panel of the Switch consists of six Gigabit ports; four are PoE-enabled and two are Gigabit uplink
ports. Each of the four PSE ports (Ports 1-4) can provide up to 30 watts (with total capacity of up to 60W);
non-PoE devices only receive data.
Reset button (Reset):
To reset the Switch press the button.
LED indicators:
The LED indicators will allow you to monitor, diagnose and troubleshoot any potential problem with the
switch, its connection or attached devices.
The following chart shows the LED indicators of the switch along with explanation of each indicator.
LED COLOR STATUS STATUS DESCRIPTION
PWR Orange On Power is supplied via the AC adapter or the PD port.
O No power is supplied to the switch
LINK/ACT Green
On A network link has been established
Flashing A network link has been established and data packets are being sent and received
O No network link is established
POE Orange
On Port is supplying power to a connected PoE device.
Flashing Abnormal power supply
O Port is not supplying power to a connected PoE device.
REAR PANEL
The rear panel of the Switch contains one grounding terminal and an AC power connector as shown.
AC Power Connector:
Power is supplied through an external AC power adapter. It supports 100 – 240 V AC, 50/60 Hz.
Grounding Terminal:
Wire the grounding terminal to an object that provides earth grounding (in rackmount installations,
grounding is typically provided by the metal frame of the mounting rack), which is located on the side of the
power supply connector.
PACKAGE CONTENTS
Before installing the Switch, make sure that the following packing list matches the items in the
packaging. If any part is lost and damaged, please contact your place of purchase as soon as
possible. In addition, make sure that you have the tools to install switches and cables on hand.
• PoE-Powered 6-Port Lite Smart Managed PoE+ Switch with 4 GbE Ports / 2 GbE Uplinks and PoE
Passthrough
• Quick Instruction Guide
• AC Power Cord

7
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
INSTALLING THE SWITCH
This section describes how to install your Switch and make connections to it. Review the following topics
and perform the procedures in the order being presented.
Use the following instructions to avoid incorrect installation, which could damage the Switch or void the
warranty.
• Place the Switch on stable surface that can safely hold the switch and any related equipment.
• Make sure the Switch will be connected to power in the proper AC input range (refer to the switch label).
• Avoid electric shock — do not open the Switch housing, even if the switch is disconnected from power.
• Make sure that there is proper clearance on all sides of the Switch for proper heat dissipation and adequate
ventilation.
DESKTOP INSTALLATION
When installing the Switch on a desktop, allow adequate space for ventilation between the device and the
objects around it. Be sure to place the switch on a stable surface that can support the weight of the switch
and any other components that may be placed on it.
WALL MOUNTING
First, install screws (not included) into the wall at appropriate distances. Then, hang the unit on the screws
and slide it into place so it is secure.

8
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
CONFIGURATION GUIDE
This section provides an introduction to the web-based conguration utility, and covers the following topics:
• Powering on the device
• Connecting to the network
• Starting the web-based conguration utility
CONNECTING TO POWER
Power down and disconnect the power cord before servicing or wiring a switch.
Do not disconnect modules or cabling unless the power is rst switched o. The device only supports
the voltage outlined in the type plate. Do not use any other power components except those
specically designated for the switch.
Disconnect the power cord before installation or cable wiring.
Connect the AC power connector on the back panel of the switch to the external
power source with the included power cord, and check the power LED is on.
CONNECTING TO NETWORK
To connect the switch to the network:
1 Connect an Ethernet cable to the Ethernet port of a computer
2 Connect the other end of the Ethernet cable to one of the numbered Ethernet ports
of the switch. The LED of the port lights if the device connected is active.
3 Repeat Step 1 and Step 2 for each device to connect to the switch.
We strongly recommend using CAT5E or better cable to connect network devices. When connecting
network devices, do not exceed the maximum cabling distance of 100 meters (328 feet). It can take
up to one minute for attached devices or the LAN to be operational after it is connected. This is
normal behavior.
Connect the switch to end nodes using a standard Ethernet cable
(UTP/STP) to connect the switch to end nodes.
!
Switch ports will automatically adjust to the characteristics (MDI/MDI-X,
speed, duplex) of the device to which the switch is connected.

9
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
LOGGING INTO THE SWITCH
This section describes how to navigate the web-based switch
conguration utility. Be sure to disable any pop-up blocker.
LAUNCHING THE CONFIGURATION UTILITY
To open the web-based conguration utility:
1 Open a Web browser.
2 Enter the IP address of the device you are configuring in the address bar on the
browser (factory default IP address is 192.168.2.1) and then press Enter.
After a successful connection, the login window displays.
LOGGINIG IN
To log in to the device conguration utility:
1 Enter the default user ID and the default password.
2 If this is the first time that you logged on with the default user ID and the default
password it is recommended that you change your password immediately.
3 When the login attempt is successful, the System Information window displays.
PARAMETER DEFAULT VALUE
Default IP address 192.168.2.1
Default Username admin
Default Password the serial number of the Switch
If you entered an incorrect username or password, an error message appears
and the Login page remains displayed on the window.
By default, the application logs out after ve minutes of inactivity.
To logout, click Logout in the top right corner of any page. The
system logs out of the device.
When a timeout occurs or you intentionally log out of the
system, a message appears and the Login page appears,
with a message indicating the logged-out state. After
you log in, the application returns to the initial page.

10
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
WEB-BASED SWITCH CONFIGURATION
The WebSmart switch software provides Layer 2 functionality for switches in your networks. This chapter
describes how to use the web-based management interface (Web UI) to congure the switch’s features.
For the purposes of this manual, the user interface is separated into
three sections, as shown in the following gure:
As you can see, the page is divided into two parts:
• The left part is the menu bar, which displays the links of all conguration functions of the
equipment, such as monitoring management and switch conguration module.
• The right part is the content area, which is divided into upper and lower parts. The upper
side is the port status bar, Chinese and English display switching and“Logout” button,
and the lower side is the page content presentation and conguration area.
Port Status Bar:
Move the mouse to the port to display the basic status of the port
(including port connection status, rate duplex and ow control
status). Click“Collapse”to hide the port status bar and display
more content areas to view other conguration information.
When a loop appears on the port, the port icon displays yellow
When the port works normally, the port icon displays green
The content area sometimes presents orange text (indicating the description of the function block)

11
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
WEB SMART CONFIGURATION
HOMEPAGE
The homepage interface displays the basic information of the device.
SYSTEM SETTINGS
DEVICE INFO
Congure the information of the device, including Device Name, Device Contact and Device Location.
IP SETTINGS
Congure device management IP (default static IP: 192.168.2.1)
When“Auto Obtain IP” is displayed as follows:
When conguring IP, the device will be disconnected briey. If automatic IP acquisition is enabled,
you need to obtain the conguration IP from the DHCP server on your network.

12
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
WEB SETTINGS
Congure web page timeout, default is 5 minutes.
The timeout can be congured for 1-60
TELNET SETTINGS
Congure Telnet timeout, default is 10 minutes.
The timeout can be congured for 1-60 minutes.
USER MANAGEMENT
Congure the account and password for web page login (The password must contain 6-16 characters
and contain only letters, numbers and the following special characters: <=>[]!@#$*().)
UPGRADE
System upgrade can be divided into Local upgrade and Online upgrade:
1 Local upgrade
Click “Select File” and select the software package you want to upgrade in the pop-
up le selection box (the software upgrade package is a le in xxx.bin format).
2 Online upgrade
This option is currently not available.

13
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
DEVICE MANAGEMENT
BUTTON DESCRIPTION
Reboot Click to restart the equipment
Restore Click to restore the factory conguration and restart the equipment
Save Cong Click to save current device congure
MONITORING
PORT STATISTICS
The Port Statistics page displays the data statistics and status of the device port, such
as the port sending and receiving rate, sending and receiving packets, etc.
CABLE DIAGNOSTICS
It is possible to perform various tests of a attached cable via the corresponding port through
cable detection (such as whether the cable is short circuited, disconnected, etc.).
Click “Start All” and wait for the test results to return.
LOOP GUARD (PART OF OUR SELF-HEALING NETWORK SUITE)
Congure enable loop guard
The port causing the loop will be shut down. After the loop is removed, the port will be up
automatically. (Default is disable).

14
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
IGMP SNOOPING
Congure IGMP Snooping
Unknown multicast Handel Action can congure FLOOD or DROP, Select
the VLAN you want to enable and click“Apply” to save.
IGMP Snooping only supports DIP mode, the maximum multicast entry is 10, Unknown multicast
Handel Action default is ood.
SWITCH SETTINGS
PORT SETTINGS
Port conguration can batch congure the status, speed, duplex, ow control and EEE
(Energy Ecient Ethernet) properties of ports. The page is divided into two parts:
Conguration part:
Select the port to be congured, then select each attribute to be
congured, and click “Apply” to distribute the conguration.
Display part:
Displays the conguration attributes and actual eective attributes of each port of the device.
PORT MONITORING
The input / output messages of one or more source image ports are forwarded
to the destination image port to monitor the network.
1. Source port and destination port cannot be the same;
2. Another mirror group is using the destination;
3. Supports 4 Session IDs

15
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
PORT ISOLATION
Congure isolation port group.
JUMBO FRAME
Congure the size of Jumbo Frames that can be forwarded.
1. Jumbo Frames can be congured with 1522, 1536, 1552, 9216 and 10000;
2. The default value of Jumbo Frames is 1522.
GREEN ENABLE
Activate the additional green ethernet options for cable length detection and power management.
STATIC MAC
The static MAC conguration is divided into two parts.
Static MAC add:
Enter the legitimate MAC address, VLAN ID, and select the congured
port number. Click “Add”to add static MAC.
Static MAC deletion and display:
After adding a legal static MAC, the corresponding data will be displayed;
Check the static MAC and click”Delete”. After the conguration is successful,
the MAC address, VLAN and corresponding port will be unbound.
Static MAC addresses maximum can be congured 16.

16
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
FILTER MAC
Congure ltered MAC address
Filter MAC addresses maximum can be congured 16.
SEARCH MAC
Search the MAC table learned by the device (support fuzzy search)
The inquiry waiting process will interrupt the communication with the equipment
MAC LIST
Displays the list of MAC learned by the device
Click “Clear Dynamic MAC”and the device will get the learning MAC list again.
The display waiting process will interrupt communication with the device
DHCP SNOOPING
Congure DHCP Snooping function, which is disabled by default.
When DHCP Snooping is enabled, you can choose to trust ports or not. As shown in the following gure,
the device sets the selected ports as trusted ports, and if it is not selected, all ports are untrusted ports;
Click “Apply”to set the selected port as a trusted port and complete the conguration of DHCP snooping.
1. Enable DHCP snooping to lter DHCP messages. For the request message from DHCP client, only
forward it to the trust port; for the response message from DHCP server, only forward the response
message from the trust port.
2. Generally, the DHCP server port (upper connection port) is set as the trust port.

17
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
VLAN SETTINGS
The homepage interface displays the basic information of the device.
VLAN MEMBER
Conguration part:
Enter a valid VLAN ID and click “Apply”to congure a new VLAN member;
Display part:
Displays the VLAN members newly added by the device, Select VLAN members in
the VLAN member list and click ”Delete” to delete VLAN members in batch
1. Congure up to 16 VLAN members;
2. When VLAN ID is bound by port, it cannot be deleted.
VLAN SETTINGS
Port VLAN conguration is divided into two parts:
Part I: Port VLAN conguration, select port, VLAN type (access and trunk, allow VLAN can be
congured under trunk), allow VLAN and native VLAN, and click “Apply”to congure and save port
VLAN (Permit VLAN and Native VLAN are selected from the VLAN members congured above);
Part II: Port VLAN list, which displays the VLAN conguration of the device port.
The message under Native VLAN does not have VLAN tag.

18
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
QOS SETTINGS
Including port rate limit and storm control functions.
PORT RATE
Congure the port ingress and egress rate, which is divided into two parts:
Conguration part:
Select one or more ports, select the conguration type and whether to enable the port speed limit (enter
the value of the port speed limit when it is enabled), and click ”Apply” to congure the port rate.
Display part:
Displays the ingress rate and egress rate of the device port conguration.
Rate limit range: 1-1000M.
STORM CONTROL
Including port storm control conguration and display:
Conguration part:
Select the congured storm control type, one or more ports and whether to enable storm control (when
enabled, enter the rate of storm control conguration), and click “Apply” to congure storm control.
Display part:
Display the storm control type and corresponding rate congured by the device
port (display the corresponding control rate when it is turned on).
Rate limit range: 1-1000M.

19
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough
User Manual
QOS (QUALITY OF SERVICE) PROPERTY
Including QoS Property conguration and display:
Conguration part:
Select the congured Enable State, Queue Scheduling Mode, Priority
Type and Weight, and click“Apply” congure QoS Property.
Display part:
Display the Enable State, Queue Scheduling Mode, Weighting of COS (Class
of Service) and DSCP (Dierentiated Services Code Point)
1. The QoS function is disabled by default;
2. The Queue Scheduling mode supports SP (Strict Priority) and WRR (Weighted Round Robin).
3. The priority type supports COS and DSCP;
4. Priority types with higher weights have higher priorities. When
the weights are the same, COS have higher priority.
COS PRIORITY MAPPING
Including conguration and display:
Conguration part:
Select the congured COS Priority and Inner Priority, and click “Apply” congure.
Display part:
Display the COS Priority and Inner Priority.
The default COS priority corresponds to the internal priority 0-7 in turn.
DSCP PRIORITY MAPPING
Including conguration and display:
Conguration part:
Select the congured DSCP Priority Mapping and Inner Priority, and click“Apply” congure.

20
PoE-Powered 6-Port Lite Smart Managed PoE+ Switch
with 4 GbE Ports / 2 GbE Uplinks and PoE Passthrough User Manual
Display part:
Display the DSCP Priority Mapping and Inner Priority.
Default DSCP priority 0-7 corresponds to internal priority 0, 8-15 corresponds to internal priority 1,
and so on.
INNER PRIORITY MAPPING
Including conguration and display:
Conguration part:
Select the congured Inner Priority and Queue ID, and click“Apply”.
Display part:
Display the Inner Priority and Queue ID.
Default internal priority 0-7 corresponds to queue ID 0-7.
QUEUE SCHEDULING
Including conguration and display:
Conguration part:
Select the congured Queue ID and Weight, and click “Apply”.
Display part:
Display the Queue ID and Weight