Intellinet 561969 User manual

54-Port L2+ Fully Managed PoE+ Switch with 48
Gigabit Ports and 6 SFP+ Uplinks
User Manual
Model 561969
intellinet-network.com

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
2
Table of Contents
1PRODUCT INTRODUCTION 4
1.1 PRODUCT OVERVIEW .................................................................................................................................4
1.2 FEATURES ................................................................................................................................................4
1.3 EXTERNAL COMPONENT DESCRIPTION ............................................................................................................5
1.3.1 FRONT PANEL ....................................................................................................................................................5
1.3.2 REAR PANEL ......................................................................................................................................................6
1.4 PACKAGE CONTENTS ..................................................................................................................................6
2INSTALLING AND CONNECTING THE SWITCH..................................................................................................7
2.1 INSTALLATION ...........................................................................................................................................7
2.1.1 DESKTOP INSTALLATION .......................................................................................................................................7
2.1.2 RACK-MOUNTABLE INSTALLATION IN 19-INCH CABINET.............................................................................................7
2.1.3 POWER ON THE SWITCH ......................................................................................................................................8
2.2 NIC CONNECTION TO THE SWITCH .................................................................................................................8
2.3 SWITCH CONNECTION TO A POWERED DEVICE...................................................................................................8
3LOGGING INTO THE SWITCH..........................................................................................................................9
3.1 SWITCH TO END NODE................................................................................................................................9
3.2 LOGIN INFORMATION .................................................................................................................................9
4WEB CONFIGURATION GUIDE......................................................................................................................11
4.1 BASIC SETUP ..........................................................................................................................................11
4.1.1 GENERAL SETUP...............................................................................................................................................12
4.1.2 IP SETUP.........................................................................................................................................................13
4.1.3 PORT SETUP ....................................................................................................................................................14
4.1.4 USER SETUP ....................................................................................................................................................16
4.1.5 DHCP ............................................................................................................................................................17
4.2 L2 LAYER APPLICATION ............................................................................................................................. 24
4.2.1 VLAN.............................................................................................................................................................25
4.2.2 MAC ADDRESS FORWARDING ............................................................................................................................28
4.2.3 PORT ISOLATION...............................................................................................................................................30
4.2.4 ERPS PROTOCOL..............................................................................................................................................31
4.2.5 LLDP PROTOCOL..............................................................................................................................................32
4.2.6 STATIC MULTICAST............................................................................................................................................33
4.2.7 MULTICAST......................................................................................................................................................34
4.2.8 LINK AGGREGATION ..........................................................................................................................................36
4.2.9 ANTI DOS ATTACK ............................................................................................................................................38
4.3 L3 LAYER APPLICATION ............................................................................................................................. 39
4.3.1 STATIC ROUTE ..................................................................................................................................................39
4.3.2 RIP SETUP.......................................................................................................................................................40

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
3
4.3.3 ARP LEARNING.................................................................................................................................................43
4.4 SECURITY APPLICATION.............................................................................................................................44
4.4.1 BROADCAST STORM CONTROL............................................................................................................................44
4.4.2 TIME RANGE....................................................................................................................................................45
4.4.3 ACL ...............................................................................................................................................................46
4.4.4 COS CONTROL .................................................................................................................................................50
4.5 NETWORK MANAGEMENT .........................................................................................................................53
4.5.1 BANDWIDTH CONTROL......................................................................................................................................53
4.5.2 MIRRORING.....................................................................................................................................................54
4.5.3 REMOTE LOGIN................................................................................................................................................55
4.5.4 HTTP STATUS ...................................................................................................................................................55
4.6 DEVICE MANAGEMENT .............................................................................................................................56
4.6.1 MANAGEMENT & MAINTENANCE .......................................................................................................................56
4.6.2 DIAGNOSTIC ....................................................................................................................................................57
4.6.3 SYSLOG ...........................................................................................................................................................57
4.6.4 ALARM ...........................................................................................................................................................58
4.6.5 POE SETUP......................................................................................................................................................59
4.6.6 PDM (POWERED DEVICE MONITOR)...................................................................................................................60
4.6.7 MTU SETUP....................................................................................................................................................61
4.6.8 SLF ................................................................................................................................................................61
4.6.9 SNMP............................................................................................................................................................62
4.6.10 RMON...........................................................................................................................................................65
4.7 SPANNING TREE PROTOCOL........................................................................................................................69
4.7.1 STP STATUS.....................................................................................................................................................69
4.7.2 MSTP ............................................................................................................................................................70
4.7.3 STP/RSTP ......................................................................................................................................................74
4.8 SYSTEM MANAGEMENT ............................................................................................................................75
4.8.1 PING ..............................................................................................................................................................75
4.8.2 CPU STATISTICS................................................................................................................................................76
5APPENDIX: TECHNICAL SPECIFICATIONS.......................................................................................................77
6ADDITIONAL INFORMATION........................................................................................................................ 79
6.1 WASTE ELECTRICAL & ELECTRONIC EQUIPMENT.................................................................................... 79
6.2 WARRANTY......................................................................................................................................... 80
6.3 REGULATORY STATEMENTS ..................................................................................................................80

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
4
1Product Introduction
Thank you for purchasing the Intellinet Network Solutions 54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit
Ports and 6 SFP+ Uplinks. Before you install and use this product, please read this manual carefully to benefit from
the full set of features that are available.
1.1 Product Overview
This switch is a high performance L3 managed PoE switch with 10G fiber ports. It provides forty-eight 10/100/1000
Mbps auto-sensing RJ45 ports, plus six 10 gigabit SFP+ optical port that can be used to link higher-bandwidth
equipment upstream. Store-and-forward technology combined with dynamic memory allocation ensures effective
bandwidth allocation at each port. This unit’s perfect QOS strategy and plenty of VLAN functionality along with easy
maintenance and management help meet the networking and access requirements of small and medium-sized
enterprises, hotels, offices and campus networks. It’s equipped with Powered Device Monitoring, a self-healing PoE
function. Often called a PoE watchdog, the function performs a PD-alive check to all connected PDs and
automatically resets unresponsive devices, such as PoE security surveillance cameras, by cutting off and then
restoring power.
The switch’s 48 ports can supply power via Power over Ethernet. Each RJ45 port supports IEEE 802.3at/af-compliant
powered devices and automatically detects and supplies the correct amount of power to compatible equipment.
1.2 Features
•Supports IEEE 802.3i, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u, IEEE 802.3z, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3ae,
IEEE 802.3az.
•Power budget of 450 W.
•Supports PoE power up to 30 W for each PoE port.
•Supports MAC address auto-learning and auto-aging.
•Forty-eight 10/100/1000 Mbps self-adapting RJ45 ports
•Six gigabit 1000/10000 Mbps SFP+ ports to link to higher-bandwidth equipment upstream.
•Store and forward switching architecture.
•Web-based management support.
•LED indicators for monitoring power, link/activity and PoE.
•Full 19-inch metal housing and internal power adapter design, suitable for rack installation.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
5
1.3 External Component Description
1.3.1 Front Panel
The front panel of the Switch consists of 1 x Reset, 1 x Mode, 1 x Console port, 48 x 10/100/1000 Mbps adaptive
Ethernet ports, 6 x 1000/10000 Mbps SFP+ ports, and a series of LED indicators. The rear panel provides an AC
power connector and grounding terminal.
Figure 1 - Front Panel
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential problem with the Switch,
connection or attached devices.
Figure 2 - LED Indicator
The following chart shows the LED indicators of the Switch along with an explanation of each indicator.
Indicator
Face plate Marker
Status
Indication
Power Status Light
PWR
Off
Power Off.
Blinking
green
Power On.
System Status
Indicator
RUN
Blinking
The system is starting.
Solid green
System startup completed.
Ethernet Port
Indicator (Link/Act
Mode)
1–48
Off
The port is NOT connected.
Solid green
The port is connected at 10/100/1000
Mbps.
Blinking
The port is sending or receiving data.
SFP+ indicator
49S–54S
Off
The port is NOT connected.
Solid green
The port is connected at 1000/10000
Mbps.
Blinking
The port is sending or receiving data.
Ethernet port
indicator
(PoE Mode)
PoE (1–48)
Off
The port is NOT connected.
Solid green
Port is connected to PD device.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
6
10/100/1000 Mbps PoE RJ45 ports (1 – 48):
Designed to connect to the device with a bandwidth of 10 Mbps, 100 Mbps or 1000 Mbps. Each has a corresponding
Link/Act/Speed indicator. Each RJ45 port also supports Power over Ethernet to connect and operate IEEE 802.3at/af
Powered Devices (PD).
SFP+ ports (49S – 54S):
Designed to install SFP+ modules. The switch features six SFP+ receiver slots. An SFP+ port connect to the device
with a bandwidth of 1000 Mbps or 10000 Mbps.
Console port (Console):
Designed to connect with the serial port of a computer or terminal for monitoring and configuring the Switch.
Mode Switch (CTRL):
Press and hold for three seconds to switch the RJ45-port LEDs to showing PoE status.
1.3.2 Rear Panel
The rear panel of the Switch contains one grounding terminal and an AC power connector as shown.
Figure 3 - Rear Panel
Grounding Terminal:
Wire the grounding terminal to an object that provides earth grounding (in rackmount installations, grounding is
typically provided by the metal frame of the mounting rack), which is located on the side of the power supply
connector.
AC Power Connector:
Power is supplied through an external AC power adapter. It supports 100 – 240 V AC, 50/60 Hz.
1.4 Package Contents
Before installing the Switch, make sure that the following packing list matches the items in the packaging. If any part
is lost and damaged, please contact your place of purchase as soon as possible. In addition, make sure that you have
the tools to install switches and cables on hand.
•54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks
•Rackmount brackets
•AC power cord
•Quick Install Guide

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
7
2Installing and Connecting the Switch
This section describes how to install your Switch and make connections to it. Review the following topics and
perform the procedures in the order being presented.
2.1 Installation
Use the following instructions to avoid incorrect installation, which could damage the Switch or void the warranty.
•Place the Switch on stable surface that can safely hold the switch and any related equipment.
•Make sure the Switch will be connected to power in the proper AC input range (refer to the switch label).
•Avoid electric shock — do not open the Switch housing, even if the switch is disconnected from power.
•Make sure that there is proper clearance on all sides of the Switch for proper heat dissipation and adequate
ventilation.
2.1.1 Desktop Installation
When installing the Switch on a desktop, allow adequate space for ventilation between the device and the objects
around it. Be sure to place the switch on a stable surface that can support the weight of the switch and any other
components that may be placed on it.
2.1.2 Rack-mountable Installation in 19-inch Cabinet
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed in a wiring closet with other
equipment. To install the Switch, please follow these steps:
A. Attach the mounting brackets on the Switch's side panels (one on each side) and secure them with the screws
provided.
Figure 4 - Bracket Installation
B. Use the screws provided to mount the Switch on the rack; tighten the screws securely.
Figure 5 - Rack Installation

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
8
2.1.3 Power on the Switch
The Switch is powered on by the 100 – 240 VAC 50/60 Hz internal high-performance power supply. Follow these
steps to connect:
AC Electrical Outlet:
It is recommended to use a single-phase three-wire receptacle with neutral outlet. Make sure to connect the metal
ground connector to the grounding source on the outlet.
AC Power Cord Connection:
Connect the AC power connector on the back panel of the Switch to the external power receptacle with the included
power cord. Check that the ON power indicator is lit, which indicates that the Switch is receiving power.
2.2 NIC Connection to the Switch
After installing the network card driver, insert the NIC into the computer. Connect one end of the twisted pair to the
RJ45 jack on your computer. Connect the other end to any RJ45 port of the Switch, with a maximum distance of 100
meters between the Switch and the computer. Once the connection is OK and the devices power on normally, the
LINK/ACT/Speed status indicator lights, corresponding to ports on the Switch.
2.3 Switch connection to a Powered Device
Ports 1 – 48 offer a PoE power supply function, which makes it possible to provide power to a Powered Device (PD)
such as a VoIP phone, network camera, wireless access point and more. You only need to connect the Switch PoE
port directly to the PD with a network cable.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
9
3Logging into the Switch
3.1 Switch to End Node
Use standard Cat5/5e (minimum) Ethernet cable (UTP/STP) to connect the Switch to end nodes as described below.
Switch ports will automatically adjust to the characteristics (MDI/MDI-X, speed, duplex) of the device to which is
connected.
Figure 6 - Connect PC to Switch
Refer to the LED Indicators. The LINK/ACT/Speed LEDs for each port lights when the link is available.
3.2 Login Information
As the Switch provides Web-based management login, configure your computer’s IP address manually to log onto
the Switch. The default settings of the Switch are shown below.
Parameter
Default Value
Default IP address
192.168.2.1
Default username
admin
Default password
The switch’s serial number
You can log into the configuration window of the Switch through the following steps:
1. Connect the Switch to the computer NIC interface.
2. Power on the Switch.
3. Check whether the IP address of the computer is within this network segment: 192.168.2.xxx ("xxx" ranges 2 –
254), for example, 192.168.2.100.
4. Open your web browser, enter http://192.168.2.1, and press Enter. The Switch login window appears, as shown
below.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
10
Figure 7- Login Windows
5. Enter the Username and Password (the factory default Username is admin and the Password is the same as the
serial number found on the bottom of the switch), and then click Login to log into the Switch configuration
window .

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
11
4Web Configuration Guide
The Switch configuration interface consists of three main areas: the status bar at the top, the left function menu bar,
and the main configuration window. Select the different functions in the function menu bar to modify all settings in
the main configuration window.
4.1 Basic Setup
Choose Basic Setup, and the following page appears. There are configurable pages for General Setup, IP Setup, Port
Setup, User Setup, and DHCP.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
12
4.1.1 General Setup
To view basic information of the Switch, such as System description, the number of ports, etc., or to modify the
System name, System contact and System location, select Basic Setup>General Setup in the navigation bar.
【Parameters & Descriptions】
Parameter
Description
System description
Brief description of device type.
System name
System name.
System Location
Specify the system location.
System contact
Include company or related URL.
【Configuration Example】
To configure general system information:
1. Click Basic Setup > General Setup.
2. Specify the system name as Switch, the location as office, and the contact information as admin for the system
administrator.
3. Click Apply.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
13
4.1.2 IP Setup
To add VLAN interfaces and configure VLAN interfaces, select Basic Setup>IP Setup in the navigation bar.
【Parameters & Descriptions】
Parameter
Description
Interface
VLAN-interface or superVLAN-interface; this parameter is optional.
VLAN ID
VLAN label.
To configure the VLAN interface, select Basic Setup>IP Setup>VLAN interface in the navigation bar.
【Parameters & Descriptions】
Parameter
Description
IP address
Secure IP address for the user to log in.
Mask
Specifies the subnet mask.
Interface name
Name of the interface.
VLAN ID
You can specify the VLAN ID.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
14
4.1.3 Port Setup
To configure the related parameters of port, select Basic Setup>Port Setup in the navigation bar.
【Parameters & Descriptions】
Parameter
Description
Port
Port number.
Status
Choose whether to enable or disable.
Link
Status: down or up.
Priority
Set port priority, the range is 0 – 7.
Set speed
Default is auto; choose from the following modes:
full-10
half-10
auto-10
full-100
half-100
auto-100
full-1000
full-10G
auto
Actual speed
The actual speed of the port.
Port description
The port is described.
【Configuration Example】
To configure static routes:
1. Click Basic Setup > Port Setup.
2. Configure the related parameters for port 47, Status is enable, Priority is 1, Set speed is auto, Mode is auto, Port

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
15
description is port 1.
3. Click Apply.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
16
4.1.4 User Setup
To change the login password of the switch or add a new user, select Basic Setup>User Setup, in the navigation bar.
【Parameters & Descriptions】
Parameter
Description
Username
Provide the username.
Password
Encrypted password.
Retype to confirm
Reconfirm password.
Privilege
Select NORMAL or ADMIN.
Terminal Type
Select Console / Telnet/ SSH / Web.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
17
4.1.5 DHCP
To configure settings for DHCP, including DHCP Pool Setup, DHCP Group Setup, DHCP Client, DHCP Snooping, DHCP
Option82, DHCP Relay and DHCP Option60, select Basic Setup>DHCP in the navigation bar.
4.1.5.1 DHCP Pool Setup
To create, edit or delete a DHCP Pool address setup, select Basic Setup>DHCP>DHCP Pool Setup in the navigation
bar.
【Parameters & Descriptions】
Parameter
Description
All Address Pool
Set the pool ID.
Address Pool Name
Set the name of ip pool.
Lease time
The lease period and day can be set to three digits,
and the hour and day can be divided into two digits.
Default Gateway
Configure the gateway corresponding to the address in
the address pool.
Ip Mask
Set Ip Mask .
First DNS
DNS server address assigned to the DHCP client.
Secondary DNS
Set Secondary DNS.
Start address
Set Start address.
End address
End Start address.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
18
4.1.5.2 DHCP Group Setup
To reference the interface configuration on the DHCP server and view groups and clients to obtain address
information, select Basic Setup>DHCP >DHCP Group Setup in the navigation bar.
【Parameters & Descriptions】
Parameter
Description
Group ID
DHCP server group ID.
IP address
DHCP server IP address.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
19
4.1.5.3 DHCP Client
To set client binding and binding entries related to DHCP Clients, select Basic Setup>DHCP >DHCP Client in the
navigation bar.
【Parameters & Descriptions】
Parameter
Description
DHCP Client Bind
Select Enable or Disable.
Unbind Assign
Select Enable or Disable.
IP Address
IP address of the bound entry.
MAC Address
MAC address of the bound entry.
VLAN
VLAN bound to the entry. The value ranges from
1 to 4094.

54-Port L2+ Fully Managed PoE+ Switch with 48 Gigabit Ports and 6 SFP+ Uplinks User Manual
20
4.1.5.4 DHCP Snooping
To set the mode, enable DHCP Snooping, enable fast deletion, and provide the IP address of the DHCP server, select
Basic Setup>DHCP >DHCP Snooping in the navigation bar.
【Parameters & Descriptions】
Parameter
Description
Mode
Global Mode, VLAN Mode, and Port Mode are
available.
Dhcp Snooping
Select Enable or Disable.
Fast Remove
Select Enable or Disable.
Dhcp Server
Set the IP address of the DHCP server.
Trust Mode
Select Enable or disable.
VLAN Id
VLAN label.
Max Learn Num
The value ranges from 0 to 9999. The default
value is 2048.