IntelliSense ST900C Installation and operating instructions

ST900C
User Manual Addendum
1. Introduction
This Addendumis intended to cover theaddition and operation of remote 5804H wire-free Keyfobs
when connected to the ST900C control panel. The Keyfobs maybe connected to either a 5882H
receiver or 6128RFH LCD Keypad. Your AlarmCompanywill informyou if this addendumis
applicable to your system. This addendumshould also be read in conjunction with the ST900C user
manual and 6128RFH LCD Keypad (if fitted) user instructions.
2. Remote Keyfobs
Thesystemcan support up to eight separate Keyfobs for settingand unsettingonly. The Keyfobs are
assigned to the systemas user numbers (egKeyfob 2= user 2). A combination of user codes and
Keyfobs maybe used.
To Add a New Keyfob
1. Enter Master Code (eg1234).
2. Press key 8.
3. Press a user number (picka user number from1 to 8).
4. Wait for adouble beep.
5. If receiver is the 5882H, press and hold all four keys on the Keyfob until a doublebeep is heard
then release the keys.
6. If receiver is the 6128RFH LCD Keypad, press and holdanythree keys on theKeyfob until a
doublebeep is heard then release the keys.
1. Press and hold anyone keyon the Keyfob until adouble beep is heard.
Note: If a triple beep is heard at anypoint, the procedurehas failed. Wait ten seconds and tryagain.
Perhaps the Keyfob is alreadyprogrammed to another user.
To Delete a Keyfob
2. Enter Master Code (eg1234).
3. Press key 8.
4. Press the user number the Keyfob belongs to (1 to 8).
5. To delete theuser code and Keyfob press *.
6. To delete theKeyfob only, wait for a double beep then press *.
Note: The Master code (user 1) cannot be deleted but a Keyfob assigned to the Master code can be
deleted. Keyfobs can be used to Full set, Part set and Night set the system. Theycan also be used to
unset the system. However, theycannot reset an alarmcondition, as this requires viewingof the
Keypad display.

ST900C User Manual Addendum Page 2 of 2
IA1-0901 Rev 1.0 Copyright ©IntelliSense 2002
3. Using the Keyfob
To set thesystemwith a Keyfob, simplypress the ‘ON’ button. Settingwill begin as described in the
Full settingsection of the user manual. Unsettingis achieved bypressingthe ‘OFF’ button.
Part settingand Night settingcanalso be achieved bypressingthe lower buttons on theKeyfob.
Keyfob Low Battery Warning
Theremote Keyfobs operate byutilisingon-board batteries, when these batteries aredue for
replacement, a low batterywarningis sent to the control panel everytime the systemis unset with a
Keyfob. Indication of low batteryis also annunciated at the remote Keypads. Dependingon the type of
Keypad installed byyour AlarmCompany, the indication will be indicated as follows.
ST900C LED Keypad
When the 5882H (receiver) detects a low batteryon a Keyfob whilst unsetting, it indicates this on the
ST900C LED Keypad byan audiblebeepand the zone LED correspondingto that Keyfob number (eg
a low batteryon Keyfob 2 will light zone LED 2). Enteringa user code will clear the indications.
User Action: Replacethe Keyfob batteries as soon as possible.
6128RFH LCD Keypad
When the 6128RFH LCD Keypad (receiver) detects a low batteryon a Keyfob whilst unsetting, it
indicates this on the Keypad byan audiblebeep and the low batterysymbol will be displayed on the
Keypad display. Enteringa user codewill clearthe indications.
User Action: Replacethe Keyfob batteries as soon as possible.
Keyfob Battery Replacement
The5804H Keyfobs require two batteries of the type listed below. Replace both batteries at the same
time.
•Maxell CR2025
•Duracell DL2025
•Varta CR2025
Battery Life: Up to 4 years (under normal conditions).
Operation of 6128RFH LCD Keypad
For further information on the operation of the 6128RFH LCD Keypad, please refer to the separate
user instructions supplied byyour AlarmCompany.
Notes