IntelliSense SpreadNet SN991-REMOTE User manual

Model SN990-KEYPAD
Wireless Keypad / Teclado Inalámbrico
Model SN991-REMOTE
Wireless Remote Transmitter / Transmisor Remoto
Inalámbrico
Remove the Battery Activator Tab from the positive
(+) end of the battery
Saque el lengüeta activador de batería del lado
positivo (+) de batería
1
2
Remove screws from back cover to open unit
Remueva los tornillos en la parte de atrás de la unidad
Installation Instructions:
SN990-KEYPAD SN991-REMOTE
Connect the SN900-PROG RF Programmer to the Molex®
connector
Use the SN900-PROG to select the appropriate system (Sierra®,
Multi-Zone, or Single Zone) Program the unit according to the
instructions listed in the SN900-PROG Programming Manual
(PN 5-051-136-00)
Conecte el programador RF SN900-PROG al conector Molex®
Usando el SN900-PROG, seleccione el sistema que esté usando
(Sierra®, Multi-Zona o Zona Única) Programe la unidad de acuerdo
a las instrucciones especificadas en el Manual de Programación
para el SN900-PROG (PN 5-051-136-00)
3
Wall Mount Assembly
Para Montaje en Pared
Visor Mount
Montaje con Multi Clip
4Replace back cover and screws
Reemplace la parte de atrás y los tornillos

IntelliSense, Sierra and SpreadNet are registered trademarks of Honeywell, Inc
All other trademarks are the property of their respective owners
Copyright 2001 IntelliSense
All rights reserved
SPE IFI ATIONS
 Dimensions:
9 5 cm x 7 0 cm x 2 0 cm
(374" L x 276" W x 079" D)
Weight:
87 9 g (3 1 oz )
 Operating frequency:
902 - 928 MHz Spread Spectrum
 Input power:
two 3 6 VDC 1/2 AA lithium batteries
 Output power:
100 mW maximum
transmitting period - 7 6 mSec
 Replace batteries only with
IntelliSense Model # SN31L-BAT
SAFT LS14250BA
 Operating environment:
0° to 60° C (32° to 140° F);
up to 95% relative humidity
(non-condensing)
 RF emission standards:
USA: FCC Part 15
ANADA: IC
DES RIP IONES DETALLADAS
 Tamaño:
9 5 cm x 7 0 cm x 2 0 cm
 Peso:
87 9 g
 Frecuencia de operación:
902 - 928 MHz Spread Spectrum
 Entrada de corriente:
dos 3 6 VDC batería
 Rendimiento de poder:
100 mW máximo
tiempo de transmisión- 7 6 mSec
 Se reponen las baterías unicamente de
IntelliSense número de modelo SN31L-BAT
SAFT LS14250BA
 Ambiente de operación:
0° to 60° C;
hasta 95% humedad relativa
(no condensar)
 RF normas de emisiónes:
USA: FCC Part 15
ANADA: IC
IMPORTANT NOTES
Batteries should be replaced following a low battery indication or
every 3 years, whichever occurs first
For continued reliability, the SN990-Keypad and SN991-Remote
should be tested at least once per month
NOTAS IMPORTANTES
Baterías se deben reponer después que se vea la indicación de
batería baja o cada 3 años, según el cual que suceda primero
Para asegurarse que el SN990-Keypad y el SN991-Remote
funcionen bien, estos deben de ser probado por lo menos una
vez al mes
US Patents 4,977,577; 5,067,136; 4,581,606 PCT/US95/
02690; 5,457,713 PCT/US95/04731; 5,265,120; 08/560,304;
5,408,217; and 5,119,396
P/N 5-051-556-00 Rev C
F NOTI E
The Models SN990-Keypad and SN991-Remote generate and use radio
frequency energy If not installed and used in accordance with the
manufacturer's instructions, they may cause interference to radio and
television reception The Keypad and Remote transmitters have been
tested and found to comply with the specifications in Part 15 of FCC Rules
for Class B Computing Devices and FCC Part 15 Subpart C, Specifications
for Intentional Spread Spectrum Radiators
If this equipment causes interference to radio or television reception - which
can be determined by turning the equipment on and off - the installer is
encouraged to correct the interference by one or more of the following
measures: 1) Reorient the antenna of the radio/television 2) Connect the
AC transformer to a different outlet so the control panel and radio/television
are on different branch circuits 3) Relocate the control panel with respect
to the radio/television
If necessary, the installer should consult an experienced radio/television
technician for additional suggestions
AUTION: IntelliSense does not support field changes or modifications to
any of the SpreadNet RF equipment unless they are specifically covered
in this manual All adjustments must be made at the factory under the
specific guidelines set forth in our manufacturing processes Any modifi-
cation to the equipment could void the user's authority to operate the
equipment and render the equipment in violation of FCC Part 15, Subpart
C, 15 247
This device complies with Part 15 of the FCC Rules Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
Industry anada
This device complies with RSS-210 of Industry Canada Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device