Intellisystem IT-7304-PC User manual

IT-7304-PC
V.35 Optic Fiber Modem
User Manual

1
Contents
Contents.........................................................................................................................................................1
1. Introduction ...............................................................................................................................................2
2. Product Features......................................................................................................................................2
3. Specifications............................................................................................................................................2
4. Description on Installation and Panels..................................................................................................3
4.1 Unpacking:......................................................................................................................................3
4.2 Front/Rear panels of the stand-alone device:............................................................................3
4.3 Front/Rear panels of Rack-mountable casing:..........................................................................5
5. IT-7304-PC Application............................................................................................................................6
5.1 Definition of signal lines at V.35 interface........................................................................................6
5.1.1 Distribution diagram of guiding feet on M34 cored jack .......................................................6
5.1.2 Definition of signal lines at V.35 interface.............................................................................6
5.2 Standard V.35 crossover cable connection diagram ................................................................8
5.3 Sittings of switch and jumper.......................................................................................................8
5.3.1 Clock setting...........................................................................................................................8
5.3.2 Phase selection .......................................................................................................................8
5.3.3 Settings of loopback test and pseudo-random code test.........................................................8
5.3.4 Framing/non-framing and time slot settings.........................................................................10
6. Common Problems................................................................................................................................11

2
1. Introduction
IT-7304-PC is a high-performance V.35 optic fiber modem developed by using a dedicated
integrated circuit. It is to modulate an N×64K V.35 data signal directly over single- or
multi-mode optic fiber for a transmission via optic cable line. At another end of the optic
cable, optical signal is demodulated into a V.35 data signal. V.35 interface may be directly
connected with the V.35 interfaces of image and data terminals or the WAN ports of MUX,
exchanger and router for a dedicated network setup or a LAN connection.
2. Product Features
Rate N×64Kbit/s (N=1～32)
Support the loopback of local analog/digital interface
Support remote loopback function
Support pseudo-random code test function
120km trunking -free transmission distance for single-mode optic fiber
Capable to be communicated with FE1 Fiber Modem
Available with complete line detection and alarm indications
Available with independent structure and 19-inch Rack-mountable structure
Rack-mountable structure can be inserted with 16 modules
AC 220V and DC –48V inputs may be selected for fiber optic modems of both structure
For Rack-mountable fiber optic modems, dual power supply heat backup is provided to
ensure a high operating reliability
3. Specifications
Optic interface:
Line mode type: CMI
Line mode rate: 2.048Mbps
Operating wavelength:850nm,1310nm or 1550nm
Optic fiber connector: SC/PC
Applicable optic fiber: multi-mode, single-mode
Transmission distance:
Single-mode: up to 120km Multi-mode: up to 2km
V.35 interface：
Data rate: N×64Kbps （N=1~32）
Available with CTS/RTS (Hardware) flow control function
Type of connector: M34 connector
Operating mode: DCE
Indicator lamps: To indicate the operating status of power supply, data receiving/sending,
loopback and random code test, code missing alarm, out-of-frame alarm etc.

3
Structure：
Independent: 140mm (depth) x 210mm (width) x 42mm (height)
Rack-mountable: 19in 4.5U standard casing
Power supply：
Independent: 85V～264VAC input, 5V/2A output
-36V～-72V DC input, 5V/2A output
Rack-mountable: 150V～260VAC input, 5V/16A, 12V/1A output
-38V～-58V DC input, 5V/16A, 12V/1A output
Power consumption: 3W
Operating temperature: 0° C～50° C
Storage temperature: -20° C～80° C
Humidity: 5%～90% (free of condensate)
4. Description on Installation and Panels
4.1 Unpacking:
After the equipment is unpacked, a check shall be done for the completeness. If any part is
found missing, please immediately contact our representative offices or agents. Complete
packing shall include the following items (for an independent product):
One set of V.35 Fiber Modem IT-7304-PC
One V.35 Fiber Modem Operation Manual
One power line(V.35 Fiber Modem/AC)
Please also contact our representative offices or agents for any transportation damage found
with this product.
4.2 Front/Rear panels of the stand-alone device:
Front panel：
Front Panel of IT-7304-PC
POWER：Power supply indicator lamp. Constantly lightening after the machine is turned on.
RXD：Data receiving indictor lamp at V.35 interface. Flash indicates that there is data output
from V3.5 interface. The quicker it flashes, the higher rate of data output from
V3.5interface.
TXD：Data sending indictor lamp at V.35 interface. Flash indicates that there is data input to
V3.5 interface. The quicker it flashes, the higher rate of data input to V3.5interface
LOF：E1 Alarm indicator lamp of input signal out-of-frame in optic line. Constantly
lightening indicates the alarm with local device; flash indicates the alarm with

4
opposite device. Alarm status of opposite device can be detected only at framing
mode.
LOS：E1 Alarm indicator lamp for code missing in optic line. Constantly lightening indicates
the alarm with local device. Flash indicates the alarm with opposite device.
LOOP：Indicator lamp of loopback test status. When local device is at a loopback status, the
lamp flashes. When local device is not at a framing mode, it is unable to detect
whether opposite device is at a loopback test status.
PTOK：Indicator lamp of pseudo-random code test. When the device is at a loopback status,
pseudo-random code test can be made. If this lamp is constantly lightening, it
indicates that pseudo-random code passes the test.
Rear panel：
Rear Panel of IT-7304-PC/AC
220VAC：AC power jack.
OFF ON：Power switch. When the ON button is pressed down, the power supply is turned
on.
V.35: V.35 interface, with a M34 cored jack.
TX RX: Receiving/sending jack of optical fiber, with TX as the sending terminal and RX as
the receiving terminal.
There is a coded switch S5 on the panel, which is used as the system configuration switch to
set such functions as clock, time slot, phase, loopback and pseudo-random code test etc.
Wherein, S5.1 and S5.2 are clock settings.
S5.1＝OFF, S5.2=OFF：network clock at V.35 interface (Received Recovered).
S5.1 ＝OFF，S5.2＝ON：network clock at the optic fiber interface (Received Recovered).
Remote time slot setting can be tracked only at this status.
S5.1=ON, S5.2=OFF: invalid
S5.1 ＝ON，S5.2＝ON：using local crystal OSC generating clock
S5.3: time slot setting
S5.3＝OFF，using remote time slot setting (valid only when S5.1 ＝OFF，S5.2＝ON)
S5.3＝ON，using local time slot setting
S5.4: for V.35 receiving clock phase selection
S5.4=OFF, using positive phase
S5.4=ON, using negative phase
S5.5: Local loopback setting (optic interface in direct loopback), ON valid.
S5.6: Local digital loopback (V.35 interface loopback), ON valid.
S5.7: Remote digital loopback (V.35 interface loopback), ON valid.
Valid at framing mode (0-time slot unused).
S5.8: Pseudo-random code test, ON valid, and valid at loopback status.

5
IT-7304-PC bottom coded switch：
Bottom Coded Switch
After time slot 0 is valid, other coded switches in whatever positions are all valid.
Select the number of time slots according to the expected rate. Normally for an independent
type, a time slot setting of automatic tracking Central Site module is selected. Coded switches
of plate-clip time slot correspond to S1, S2, S3 and S4.
Rear Panel of IT-7304-PC/DC
48V DC：DC -48V power supply connector
The others are the same as AC Rear Panel
4.3 Front/Rear panels of Rack-mountable casing:
RACK front panel：
Front Panel of RACK
+5V: 5V main power supply indicator lamp
+12V: 12V fan power supply indicator lamp
Under the panel is a group of indicator lamps matrix:
PWR: power supply lamp
RXD: lightening upon data receiving at V.35
TXD: lightening upon data sending from V.35
LOS: lightening when the optic line gets lost
LOF: lightening after a synchronization of data out-of-frame
TEST: lightening during loopback test (equivalent to LOOP)
PTOK: lightening after a successful pseudo-random code test

6
RACK/ACAC redundancy power supply panel：
RACK/AC AC Redundancy Power Supply Panel
160~270 VAC：AC 220V input jack
ON OFF：power switch
+5V：5V main power supply indicator lamp；
+12V：12V fan power supply indicator lamp
RACK/DC DC redundancy power supply panel：
RACK/DC DC Redundancy Power Supply Panel
40~60 VDC：DC-48V input connector (FG grounded, with“- +” terminals connected with
48V input)
ON OFF：power switch
+5V：5V main power supply indicator lamp
+12V：12V fan power supply indicator lamp
5. IT-7304-PC Application
5.1 Definition of signal lines at V.35 interface
5.1.1 Distribution diagram of guiding feet on M34 cored jack
Distribution diagram of guiding feet on M34 cored jack
5.1.2 Definition of signal lines at V.35 interface
As shown :( Operating mode：DCE)

7
Definition of Signal Lines at V.35 Interface
V.35 Feet
Signal
Function
Direction
A
CGND
Frame ground
——
B
GND
signal ground
——
C
RTS
request to send
input
D
CTS
consent to send
output
E
DSR
data set ready
output
F
DCD
data carrier detection
output
H
DTR
data terminal ready
input
P
TXD A
transmitting data
line A
input
S
TXD B
transmitting data
line B
input
R
RXD A
receiving data line A
output
T
RXD B
receiving data line B
output
U
EXTCLK
A
exterior clock line A
input
W
EXTCLK
B
exterior clock line B
input
V
RXCLA
receiving clock line
A
output
X
RXCL B
receiving clock line
B
output
Y
TXCLA
transmitting clock
line A
output
AA
TXCL B
transmitting clock
line B
output

8
5.2 Standard V.35 crossover cable connection diagram
V.35 feet
V.35 feet
CGND
A
—————
A
CGND
GND
B
—————
B
GND
RTS
C
—————
D
CTS
CTS
D
—————
C
RTS
DSR
E
—————
H
DTR
DTR
H
—————
E
DSR
TXDA
P
—————
R
RXDA
TXDB
S
—————
T
RXDB
RXDA
R
—————
P
TXDA
RXDB
T
—————
S
TXDB
EXCA
U
—————
V
RXCA
EXCB
W
—————
X
RXCB
RXCA
V
—————
U
EXCA
RXCB
X
—————
W
EXCB
5.3 Sittings of switch and jumper
Independent device has totally 5 setting switches, with S5 located on the rear panel and
S1~S4 under the bottom cover. The user can easily make settings without the need to open the
cover.
5.3.1 Clock setting
V.35 interface timing (S5.1= OFF, S5.2=OFF): the sending timing is V.35 port timing, and the
received data, after buffering, is synchronized with V.35 port timing.
Optic interface receiving timing (optic interface originated from the clock, S5.1=OFF，
S5.2=ON): the sending timing is optic interface receiving timing, and the received data, after
buffering, is synchronized with optic interface receiving timing. Under this timing mode, local
time slot setting can automatically track the opposite time slot setting.
Local main timing (S5.1=ON, S5.2=ON): the sending timing is of local crystal OSC, and the
received data, after buffering, is synchronized with local timing.
5.3.2 Phase selection
S5.4 is used for the receiving phase selection of V.35 interface.
5.3.3 Settings of loopback test and pseudo-random code test
S5.5～S5.8 of coded switch S5 are used for setting the loopback test and pseudo-random code
test.
S5.5 is local loopback control （LLOOP）and optic interface is directly looped back to
V.35 interface. “OFF” indicates normal operation; “ON” indicates local loopback test. The
default is “OFF”. It is used for testing whether local device is in normal operation.

9
Local Loopback Schematic
S5.6: local digital loopback control (DLOOP). “OFF” indicates normal operation; “ON”
indicates local digital loopback. The default is “OFF”. With a loopback from local V.35
interface to E1 optic interface, it is used for testing whether the remote device and E1 optic
line are in normal operation.
Local Digital Loopback
S5.7:“OFF”indicates normal operation ；“ON”indicates command remote loopback. The
default is “OFF”. As this command must be sent through E1 optic line to remote end for
validness, it will become invalid at the following two cases: ①the remote end is not
V.35 Fiber Modem device; ②V.35 Fiber Modem is working at a non-framing status, at
this moment all time slots of E1 are used for transmitting the data from V.35 interface at
a rate of 2048Kbps. Through a transmission of loopback command from local device to
remote device, the command remote loopback is achieved.
Remote Loopback
S5.8: Pseudo-random code test control (PATT). “OFF” indicates normal operation; “ON”
indicates pseudo-random sequence test. The default is “OFF”. It generates a
pseudo-random sequence code to be transmitted to V.35 optic line output terminal and
tests whether V.35 optic line input signal is in compliance with this sequence standard,
so as to judge whether the device and line transmission have an error code.
Pseudo-random Code Test
V.35 Fiber Modem V35 Optical
Interface
Fiber Modem V35 Optical
Interface
V.35
Fiber Modem V35
V.35 V.35
Fiber Modem V35 Fiber Link
Remote
Local
V.35
V.35 Fiber Modem V35 Fiber Modem V35
Local Remote
Fiber Link

10
Remark: Pseudo-random sequence code test can be made only under a loopback status. At
this moment, constantly lightening of LOOP and PTOK/CRC lamps shows local status, flash
shows remote status; TXD and RXD lamps are used for showing the status of local TXD or
RXD.
5.3.4 Framing/non-framing and time slot settings
Totally 32 coded switches S1, S2, S3 and S4 are used for E1 time slot setting.
E1 Time Slot Setting
1st switch (S1.1) is used for controlling E1 framing/non-framing. “ON” refers to
non-framing mode.
31 switches, from 2nd—32nd(S1.2~S1.8, S2, S3, S4), are respectively used for controlling
the selection of 1st –31st time slots. Set at “ON”, the corresponding time slot is selected;
set at “OFF”, the corresponding time slot is not selected. The rate of V.35 interface is
completely dependent on the number of the selected time slots. For example: the setting
of 3rd switch to “ON” and all other switches to “OFF” indicates that 2nd time slot is
selected, at this moment the rate is 64K; the setting of 7th and 8th switches to “ON” and all
other switches to “OFF” indicates that 6th and 7th time slots are selected, with a rate of
2×64K=128K. TS0 setting is used for specifying E1 frame to be transparent or framing:
“0”--framing, “1”--non-framing. But the bit has to be specified in combination with other
time slots. TS16 setting is used for controlling E1 frame structure to be PCM30（CAS）
or PCM31（CCS）: ‘0’—PCM30, at this moment 16th time slot must not be used for
transmission service; ‘1’—PCM31, 16th time slot can be used for transmission service.
Besides, TS1—TS31 are respectively used for controlling the selection of 1st—31st time
slots: ‘1’—the corresponding time slot is selected; ‘0’—the corresponding time slot is not
selected.
Typical application：Non-framing mode: 1st switch is set to “ON”, and all other switches
to “OFF” (other switches are located in such a way that the setting of non-framing is
unaffected) Framing mode: 1st switch is set to “OFF”, and all other switches are set
according to the time slot positions to be used by E1 channel and the rate of V.35 port. (If
it is set to tracking remote time slot, the time slot switch will become invalid)
Attention: Ex-works S1, S2, S3 and S4 are all set to “OFF”
Attention: The setting of tracking remote time slot; S5.2 to “ON”; S5.1 and S5.3 to “OFF”

11
6. Common Problems
Common Failures and Solutions
No.
Failure
Cause
Solution
1
PWR power supply
indicator lamp not
lightening
1.Power supply not properly
connected
2.Protector tube damaged
3. -48V DC input tie-line in
reverse connection
4.Internal power supply circuit
with failure
1.Check power switch and jack
2.Replace protector tube 3.Correct -48V
power supply line connection
4. Returned to the manufacturer for
repair.
2
LOF out-of-frame
alarm lamp lightening
1.Optic interface not clean
2.Optic fiber not well inserted
3.Wrong clock setting
4.Time slots of the devices at
two ends not conformance
5.Internal circuit damaged
1. Clean the connector of optic interface
2. Insert the SC connector in place
3. Refer to the description on rear panel
4. Returned to the manufacturer for
repair.
3
LOS data loss alarm
lamp lightening
1. Optic fiber in wrong
interconnection
2.Optic fiber not well inserted
3.Optic fiber broken
4.Internal circuit damaged
1. Correct the connection
2. Insert the SC connector in place
3. Check optic cable
4. Returned to the manufacturer for
repair.
4
TXD lamp not
lightening
V.35 interface not well
connected or the router etc. not
turned on.
1. Check the connecting line and
terminal device