Intellitouch Pool and Spa Control System User manual

IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
pool/spa control system
IntelliTouch®
Pool and Spa Control System
Personality Kit
Installation Guide

© 2008 Pentair Water Pool and Spa, Inc. All rights reserved
This document is subject to change without notice
1620 Hawkins Ave., Sanford, NC 27330 • [phone]
10951 West Los Angeles Ave., Moorpark, CA 93021 • [phone]
Trademarks and disclaimers
IntelliTouch®, QuickTouch, MobileTouch®, ScreenLogic®and Pentair Water Pool and Spa®are trademarks and/or
registered trademarks of Pentair Water Pool and Spa, Inc. and/or its affiliated companies in the United States and/or
other counties. Crestron® is registered trademark of Crestron Inc. AMX®is registered trademark of AMX Inc.
Liton™ is trademark of Liton Inc. Unless noted, names and brands of others that may be used in this document are
not used to indicate an affiliation or endorsement between the proprietors of these names and brands and Pentair
Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those parties
or others.
P/N 520101 - Rev D - 10/01/08

i
IntelliTouch Personality Kit Installation Guide
Contents
IMPORTANT SAFETY PRECAUTIONS ............................................................... iii
Introduction .............................................................................................................. 1
IntelliTouch System Overview ................................................................................. 1
In the home .................................................................................................. 1
Around the pool ........................................................................................... 1
At the equipment pad ................................................................................... 1
IntelliTouch System Components ............................................................................ 2
Load or Power Center.................................................................................. 2
IntelliTouch Personality Kits ......................................................................... 2
IntelliTouch Personality Kit Contents............................................................ 3
In this Installation Guide .......................................................................................... 3
IntelliTouch Interfaces .............................................................................................. 4
IntelliTouch in your home ............................................................................. 6
IntelliTouch Interface Kits......................................................................................... 7
PC Interface (iTC15 Kit - P/N 520500) ........................................................ 7
Personal Digital Assistant (PDA) (iTC25 Kit - P/N 520501) ......................... 7
In-Wall Touch Screen (iTC35 Kit - P/N 520502)........................................... 7
Digital Wireless Tablet (iTC45 Kit - P/N 520503) .......................................... 7
IntelliTouch ScreenLogic Interface Accessory Kits ................................................. 7
Installation Steps Summary..................................................................................... 8
Tools required .............................................................................................. 8
Accessory Equipment ............................................................................................. 9
Plumbing Requirements .......................................................................................... 10
Equipment Location ..................................................................................... 11
High Voltage Connections ....................................................................................... 14
Power Center and Load Center Description ................................................ 14
Power Center (without Sub-panel) ............................................................... 14
Load Center (with built-in Sub-panel)........................................................... 15
Installing the Outdoor Control Panel ........................................................................ 16
Connecting the Pre-Installed Relays ....................................................................... 17
Installing Auxiliary Relays ....................................................................................... 18
Installing the Valve Actuator .................................................................................... 19
Installing and Connecting Temperature Sensors ..................................................... 20
Water Temperature Sensor .......................................................................... 20
Ambient Air Temperature (Freeze Protection) Sensor ................................. 20
Solar Temperature Sensor (Optional) .......................................................... 20
Connecting IntelliTouch to a Standard Gas Heater .................................................. 21
Connecting the Transformer .................................................................................... 21

ii
IntelliTouch Personality Kit Installation Guide
Contents (Continued)
Installing the Indoor Control Panel ........................................................................... 22
Drill Control Panel Wall Mounting Holes ....................................................... 22
Cabling the Indoor Control Panel at the Load Center ................................... 23
Cabling the Indoor Control Panel ................................................................. 24
MobileTouch Wireless Controller ............................................................................. 26
Mounting and Connecting the MobileTouch Transceiver Module ................. 26
Connecting the Transceiver to the Personality Board .................................. 28
Using the MobileTouch Wireless Controller ................................................. 28
Setting up the MobileTouch Wireless Controller ........................................... 29
Charging the MobileTouch Wireless Controller ............................................ 31
System Start-Up ..................................................................................................... 32
Check Electronics ....................................................................................... 32
System Test ................................................................................................. 32
Testing the auxiliary relays .......................................................................... 32
Solar System Installation ............................................................................. 33
Solar System Start-Up ................................................................................ 33
System Wiring Diagram (Power Center/Load Center) ................................. 34
Glossary.................................................................................................................. 36
Technical Support
Sanford, North Carolina (8 A.M. to 5 P.M. ET.)
Moorpark, California (8 A.M. to 5 P.M. PS.)
Phone: [phone]
Fax: [phone]
Web sites
http://www.pentairpool.com and staritepool.com
Download the IntelliTouch®User’s Guide (PDF) from the Web
http://www.pentairpool.com/owners_manuals/controls/IntelliTouch_Pool_Spa_Cntrls_Instll_Guide.pdf
Related IntelliTouch Manuals
IntelliTouch Load Center Installation Guide (P/N 520100)
IntelliTouch Expansion Center Kit User’s Guide (P/N 520471)
IntelliTouch i-Link Protocol Interface Adapter User’s Guide (P/N 520450)
ScreenLogic®User’s Guide (P/N 520493)
ScreenLogic Video & Lighting Protocol Adapter User’s Guide (P/N 520936)

iii
IntelliTouch Personality Kit Installation Guide
IMPORTANT SAFETY PRECAUTIONS
Important Notice:
Attention Installer: This manual contains important information about the installation, operation
and safe use of this product. This information should be given to the owner and/or operator of this
equipment.
WARNING - Before installing this product, read and follow all warning notices and instructions
which are included. Failure to follow safety warnings and instructions can result in severe injury,
death, or property damage. Call [phone] for additional free copies of these instructions.
WARNING - Water temperature in excess of 100 degrees Fahrenheit may be hazardous to your
health. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the
internal temperature of the body reaches a level several degrees above normal body temperature of
98.6° F (37° C). The symptoms of hyperthermia include drowsiness, lethargy, dizziness, fainting,
and an increase in the internal temperature of the body.
The effects of hyperthermia include: 1) Unawareness of impending danger. 2) Failure to perceive
heat. 3) Failure to recognize the need to leave the spa. 4) Physical inability to exit the spa. 5) Fetal
damage in pregnant women. 6) Unconsciousness resulting in danger of drowning.
WARNING - To reduce the risk of injury, do not permit children to use this product unless they
are closely supervised at all times.
WARNING - The use of alcohol, drugs, or medication can greatly increase the risk of fatal
hyperthermia in hot tubs and spas.
WARNING - Control System is intended to control heaters with built-in high limit circuits ONLY.
Failure to do so may cause property damage or personal injury.
WARNING - Do not use this product to control an automatic pool cover. Swimmers may become
entrapped underneath the cover.
WARNING - For units intended for use in other than single-family dwellings, a clearly labeled
emergency switch shall be provided as part of the installation. The switch shall be readily accessible
to the occupants and shall be installed at least 10 feet (3.05 m) away, adjacent to, and within sight of,
the unit.
CAUTION - Except for listed spa-side remote controls, install a minimum of five (5) feet from
the inside wall of the pool and spa.

iv
IntelliTouch Personality Kit Installation Guide
IMPORTANT SAFETY PRECAUTIONS (Continued)
FCC Regulatory Safety Notice - The MobileTouch wireless control panel device has been
tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This device generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Modifications not expressly approved by the party responsible for FCC compliance could
void the user’s authority to operate the equipment.
General Installation Information
1. All work must be performed by a licensed electrician, and must conform to all national, state,
and local codes.
2. Install to provide drainage of compartment for electrical components.
3. If this system is used to control underwater lighting fixtures, a ground-fault interrupter
(GFCI) must be provided for these fixtures. Conductors on the load side of the ground-fault
circuit-interrupter shall not occupy conduit, junction boxes or enclosures containing other
conductors unless such conductors are also protected by a ground-fault circuit-interrupter.
Refer to local codes for details.
4. A terminal bar stamped is located inside the supply terminal box. To reduce the risk of
electric shock, this terminal must be connected to the grounding means provided in the
electric supply service panel with a continuous copper wire equivalent in size to the circuit
conductors supplying this equipment (no smaller than 12 AWG or 3.3 mm). The bonding
lug(s) provided on this unit are intended to connect a minimum of one No. 8 AWG for US
installation and two No. 6 AWG for Canadian installations solid copper conductor between
this unit and any metal equipment, metal enclosures or electrical equipment, metal water
pipe, or conduit within 5 feet (1.5 m) of the unit.
5. The electrical supply for this product must include a suitably rated switch or circuit breaker
to open all ungrounded supply conductors to comply with Section 422-20 of the National
Electrical Code, ANSI/NFPA 70.1987. The disconnecting means must be readily accessible
to the tub occupant but installed at least 10 ft. (3.05 m) from the inside wall of the pool.
6. Supply conductor must be sized to support all loads. Maximum supply conductor current
must be 125 Amps at 125 VAC or 63 Amps at 240 VAC.

1
IntelliTouch Personality Kit Installation Guide
Introduction
Welcome! Your Pentair IntelliTouch Pool and Spa and Control System will change the way you view pool
and spa controls. This innovation in pool and spa automation offers complete freedom for you while
having full automation control over your pool, spa, lights, heater, pump, cleaners and much more.You
can now schedule multiple start and stop times to control your lights, heater, spa jets, and filter pumps.
Using the IntelliTouch Indoor Control Panel or MobileTouch®wireless control panel you can control your
pool, spa, and lights from anywhere inside or outside your home. Optional controllers are also available
such as the wireless Digital Tablet or Personal Digital Assistant (PDA), and in-wall Touch Screen that
can interface with your PC. IntelliTouch is a scalable system that can be upgraded to a completely
integrated home automation solution including audio, security, climate, irrigation and more. For more
information about using these interfaces, refer to the IntelliTouch ScreenLogic®Interface Accessory Kits
on page 7.
IntelliTouch System Overview
An IntelliTouch system can include five (5) to 40 high voltage relays circuits that can be used to control
any combination of pumps, lights, water features. A maximum of ten (10) relays can be housed in an
IntelliTouch Load Center or Power Center. Up to three (3) Load Centers or Power Centers can be
connected to a main Load Center for a maximum of 40 relays. User-configurable circuits can be used to
control equipment. The “Feature Macro” circuits feature allows any number of circuits to be combined
and controlled by a single button.
An optional IntelliTouch Dimmer Module (P/N 520406) can be installed for use to dim any high voltage
incandescent light such as Pentair Amerlite®and Pentair SpaBrite®lights. The dimmer module supports
multiple lights from 100 watts up to 1,000 watts and installs in a standard relay location. Any number of
dimmers (up to 10 maximum) may be used with a maximum combined load of 4,000 watt in a single
Load Center.
In the home
The IntelliTouch system can utilize multiple wired and wireless controllers including the Digital Tablet,
Personal Digital Assistant (PDA), the wired in-wall Touch Screen, Indoor Control Panel, and the wireless
MobileTouch remote control panel. Your existing home PC can also be used to control the IntelliTouch
system via the ScreenLogic interfaces. A maximum of four (4) ScreenLogic interfaces can be used, for
example, four Tablets, or four PDA’s, or four in-wall Touch Screen’s, or four PC’s in any combination.
Around the pool
Located near your spa, the IntelliTouch, iS10 or iS4 spa-side remote provide control buttons for various
pool and spa functions. The iS10 spa-side remote also provides a temperature display.
At the equipment pad
The pool pump, filter, and various IntelliTouch remote controllers and interfaces are connected to the
IntelliTouch Load Center and/or Power Center enclosure which are located at the equipment pad. The
Load Center enclosure is where the high voltage lines from the circuit breaker panel junction box at the
home are connected to. The pool service person can periodically check pool operations from the Load
Center.
Also at the equipment pad there are system pool and spa pipes connected to the pump, heater and
filtration system. Mounted on top the valves are motorized valve actuators used to automatically change
the direction flow of water through the plumbing system. There are also temperature sensors and a
cable that connects to the heater.

2
IntelliTouch Personality Kit Installation Guide
IntelliTouch System Components
The main required components of an IntelliTouch system is a Load Center or Power Center,
IntelliTouch Personality Kit, and Interface:
Load or Power Center
• Load Center: Provides a larger footprint (17" W x 23" H) Includes built-in sub panel (125 AMPS)
capable of holding up to eight 1” breakers. Also includes five 25 AMP three HP relays, 110/240 V
transformer with secondary side circuit protection. Multiple knockouts for different sizes of conduit
are supplied as well as a GFCI side knockout. The Load Center provides ample space for all high
and low voltage wiring needs.
•Power Center: Offers a smaller footprint (17" W x 17" H) than the Load Center. The Power Center
does not include a circuit breaker base. Users should choose this enclosure if they already have
existing circuit breakers/sub-panel for their equipment.
•Expansion Kits: Models i5X and i10X, offer five or ten additional Auxiliary Circuits for systems
i9+3, i9+3S and i10+3D. Each IntelliTouch Expansion Kit requires a Load Center (P/N 520136) or
Power Center (P/N 520137). Up to three Expansion Kits and Load or Power Centers may be
added to a system, for control of up to 38 Auxiliary Circuits (40 auxiliary circuits for i10+3D).
IntelliTouch Personality Kits
There are several types of IntelliTouch control systems available for different pool/spa configurations:
• Shared Equipment: Pool and spa combinations with shared filtration system –Pool owners
can enjoy the convenience of motorized valves for water flow separation between pool and spa.
The Personality Kit models are:
•i5+3 (P/N 520505) – Four auxiliary circuits plus filter pump operation (create a Feature
circuit for valve actuators without using an existing output auxiliary circuit, and special
light functions for color lighting). Five relays are included in the Load Center.
•i7+3 (P/N 520507) – Six auxiliary circuits plus filter pump operation and the +3 option
(create a Feature circuit for valve actuators without using an existing output auxiliary
circuit, and special light functions for color lighting). Two relays are included in the kit
and five in the Load Center.
•i9+3 (P/N 520509) – Eight auxiliary circuits plus filter pump operation and the +3 option
(create a Feature circuit for valve actuators without using an existing output auxiliary
circuit, and special light functions for color lighting). Four relays are included in the kit
and five in the Load Center.
• Dual Equipment: Pool and Spa with Dual Sets of Equipment –The IntelliTouch i10+3D
(P/N 520510) is designed to operate two sets of pool equipment. Each set of a equipment (Pool or
Spa) can control one temperature setting. This IntelliTouch Personality Kit can control up to 10
pumps and/or lighting circuits, plus two heater circuits. The Personality Kit includes, eight auxiliary
circuits plus a filter pump.
The +3 option (create a Feature Macro circuit for valve actuators without using an existing output
auxiliary circuit). Five relays are included in the kit and five in the Load Center. You can create a
Feature circuit for valve actuators without using an existing output auxiliary circuit, and special
light functions for color lighting.

3
IntelliTouch Personality Kit Installation Guide
• Single Equipment: Pool Only or Spa Only Applications –The IntelliTouch i5S+3 (P/N 520506)
and i9+3S provide advanced automation for a single body of water. The i5S+3 Personality Kits
includes four auxiliary circuits plus filter pump operation. Five relays are included in the Load
Center. The i9+3S (P/N 520508) Personality Kits includes eight auxiliary circuits plus filter pump
operation and the +3 option (create a Feature Macro circuit for valve actuators without using an
existing output aux circuit). Four relays are included in the kit and five in the Load Center. You can
create a Feature circuit for valve actuators without using an existing output auxiliary circuit, and
special light functions for color lighting. This model also allows HI-TEMP and LO-TEMP settings.
IntelliTouch Personality Kit Contents
The following items are included in the IntelliTouch Personality Kit. If any item is missing or damaged
in the IntelliTouch kit, contact your authorized dealer, or contact Pentair Technical Support (page 9).
• An IntelliTouch interface (see page 4)
• Outdoor Control Panel. Includes a motherboard and a Personality circuit board.
• Power Relays - (Models i5+3, i5S+3 no relays, i7+3 Qty. 2, i9+3, i9+3S Qty 4, i10+3D Qty 5,
i5x (no relays, i10x (5 relays)
• Valve Actuators - Qty 2 (Models i5+3, i7+3, i9+3)
• Temperature Sensors - Water Sensor (with long cable, including o-ring and hose clamp),
Air Sensors (with short cable). For i10+3D only, two Water Sensor (with long cable)
• Wiring Diagram Label for models i5S+3 and i9+3S and i10+3D. For models i5+3, i7+3, i9+3,
refer to the Load Center and Power Center inside front door.
• Load Center or Power Center parts bag: Includes relay screws. (see page 2)
• Label Sheet - A set of adhesive labels for custom identification (used to label the outdoor
control panel buttons). Use a pair of fine-tip tweezers to remove the labels from the sheet.
• IntelliTouch Personality Kit Installation Guide (this manual)
In this Installation Guide
Use the information in this manual for installing the IntelliTouch Personality Kit contents.
• For Load Center and Power Center installation instructions, refer to the Load Center and
Power Center Installation Guide (P/N 520100).
• For Accessory installation and operation instructions, refer to the User’s Guide provided
with the accessory.
Note: For IntelliTouch Indoor and MobileTouch Controller, refer to the IntelliTouch System
User’s Guide (P/N 520102).

4
IntelliTouch Personality Kit Installation Guide
IntelliTouch Interfaces
Choose one or more of the following interface options to control pool and spa operations.
• iTC15 Kit (P/N 520500) – Includes Protocol Interface Adapter and wireless router that connects to
existing Desktop or Laptop PC. This allows control of IntelliTouch pool and spa systems via PC
(requires PC with an Ethernet connection, and Windows XP operating system).
• iTC25 Kit (P/N 520501) – Includes Wireless Personal Digital Assistant (PDA) with 3.5" color touch
screen custom configured for IntelliTouch systems, wireless router, and a Protocol Interface
Adapter.
• iTC35 Kit (P/N 520502) – Includes in-wall color touch screen with Ethernet (RJ45) connection
and Protocol Interface Adapter and wireless router. The in-wall Touch screen is custom configured
for IntelliTouch systems. Requires an Ethernet cable to router.
• iTC45 Kit (P/N 520503) – Includes wireless Tablet with color touch screen, Protocol Interface
Adapter, and wireless router. The Tablet is custom configured for IntelliTouch
systems.
In-Wall Touch Screen
Digital Tablet
PDA

5
IntelliTouch Personality Kit Installation Guide
Indoor Control Panel MobileTouch® Wireless Controller
i-Link™ Protocol
Interface Adapter
QuickTouch®
wireless remoter
(QT4)
• Indoor Control Panel (P/N 520138) – 3.75’’ monochrome backlit LCD control panel. Connects to
the Personality board in the Load Center.
• MobileTouch Kit (P/N 520906) – 3.75’’ monochrome backlit LCD wireless control panel with
Transceiver antenna. Allows any IntelliTouch wired system to also have a wireless remote with all
the capabilities of the Indoor Control Panel. With an average range of 300 feet, pool owners have
system control anywhere around the home or yard. Powered by a rechargeable lithium-ion battery.
Includes a cradle for recharging. The MobileTouch control panel
without the Transceiver antenna (P/N 520907) is also available.
• QuickTouch®Wireless Remote (QT4) - (P/N 520148): Four-function wireless remote for pool and
spa functions of your choice. This controller transmitter operates up to 150 feet range from the
Load Center or Power Center.
• iS10 and iS4: 10-function (iS10) and 4-function (iS4) Spa-Side remote controller for pool and spa
functions of your choice. The controllers can operate up to 150 feet range from the Load or Power
Center.
• i-Link™Protocol Interface Adapter (P/N 520442): Allows home automation systems such as
Crestron®, AMX®, Liton™ and others to control IntelliTouch.

6
IntelliTouch Personality Kit Installation Guide
10
9
5
7
8
1
3
4
26
Personal Computer (PC): Existing home owner’s PC or Laptop. Connects to a wireless router
and the IntelliTouch Protocol adapter for control of IntelliTouch pool/spa systems. Requires a PC/
Laptop (Windows XP) with Ethernet/RJ45 adapter installed.
Personal Digital Assistant (PDA): This wireless PDA with a color touch screen enables you to
control your pool and spa features using the IntelliTouch ScreenLogic interface. The PDA is
custom configured for IntelliTouch systems.
In-wall Touch Screen: A color display with Ethernet (RJ45) connector. Connects to the provided
wireless router and Protocol adapter via Ethernet (RJ45) for control of IntelliTouch pool and spa
systems. The in-wall Touch Screen is custom configured for IntelliTouch systems.
Wireless Tablet: This control panel consists of a color touch screen. Receives and transmits
commands via wireless router and Protocol adapter for control of IntelliTouch pool/spa systems.
The Tablet is custom configured for IntelliTouch systems.
Indoor Control Panel: This control panel consists of a 3.75’’ monochrome backlit LCD and
connects to the Personality Board in the Load Center or Power Center for control of IntelliTouch
pool and spa systems.
MobileTouch: This wireless control panel has a 3.75’’ monochrome backlit LCD. Receives and
transmits commands via the Transceiver antenna located at the Load or Power Center.
Wireless router: Connects to the PC or Laptop via Ethernet connection to the Protocol adapter.
Protocol adapter: Connects to wireless router via Ethernet connection and to Personality board
(Load/Power Center) via a four-wire 22-AWG cable.
Load Center or Power Center. The main control center. Includes the Outdoor Control Panel that
controls pump, heater, and light relays. Receives commands via Protocol adapter, and wireless
and wired control panels connected to the Personality board.
MobileTouch Transceiver antenna: Connects to the Personality circuit board. Sends and
receives commands to and from the MobileTouch wireless control panel.
IntelliTouch in and around your home
1
2
3
4
5
6
7
8
9
10

7
IntelliTouch Personality Kit Installation Guide
IntelliTouch Interface Kits
The following items are included in your IntelliTouch interface kit.
PC Interface (iTC15 Kit - P/N 520500)
• Protocol adapter for use with existing Desktop or Laptop PC
• Wireless router (802.11b/g) with AC adapter
• IntelliTouch ScreenLogic User’s Guide
• CD-ROM containing IntelliTouch ScreenLogic PC user interface software
Personal Digital Assistant (PDA) (iTC25 Kit - P/N 520501)
• Personal Digital Assistant (PDA) with built-in Wi-Fi 802.11 wireless LAN adapter with antenna.
Refer to the manufacturers documentation for kit contents
• Wireless router (802.11b/g) with AC adapter
• Protocol adapter
• IntelliTouch ScreenLogic User’s Guide
• CD-ROM containing IntelliTouch ScreenLogic PC user interface software
In-Wall Touch Screen (iTC35 Kit - P/N 520502)
• In-wall Digital Tablet, and AC adapter
• Wireless router (802.11b/g) with AC adapter
• Protocol adapter
• IntelliTouch ScreenLogic User’s Guide
• CD-ROM containing IntelliTouch ScreenLogic PC user interface software
Digital Wireless Tablet (iTC45 Kit - P/N 520503)
• Digital Tablet (with internal battery pack), stylus, built-in Wi-Fi 802.11 wireless LAN adapter with
antenna.
• Wireless router (802.11b/g) with AC adapter
• Protocol adapter
• IntelliTouch ScreenLogic User’s Guide
• CD-ROM containing IntelliTouch ScreenLogic PC user interface software
IntelliTouch ScreenLogic Interface Accessory Kits
Up to a total of four ScreenLogic interfaces can be used with an IntelliTouch system, as
shown above. If you need additional interfaces, first order one of the ScreenLogic interface
kits, then order one or more of the following accessory interfaces accessory kits:
• PDA, CD-ROM and manual (P/N 520497)
• In-Wall Touch Screen, CD-ROM and manual (P/N 520498)
• Tablet, CD-ROM and manual (P/N 520499)
Note: The above Accessory Kits interfaces do not include a Protocol adapter or wireless router.

8
IntelliTouch Personality Kit Installation Guide
Installation Steps Summary
Note: The following installation instructions assume that the Load Center or Power Center is
installed at the equipment pad. For Load Center and Power Center installation instructions, refer to
the Load Center and Power Center Installation Guide (P/N 520100).
The recommended installation steps for the Personality Kit parts are as follows:
Install the Outdoor Control Panel (page 16): Install the Personality board in the Load Center
or Power Center. Also, review the high voltage connection locations in the Power/Load Center.
Connect pre-installed relays (page 17): Connect the relay plugs to the Personality board.
The four relays are pre-installed in the Power/Load Center.
Install auxiliary relays (page 18): Install and connect the relay(s). The number of relays
included in the Personality Kit depend on the Outdoor Control Panel model (i5, i5S (none),
i7+3 (Qty. 2), i9+3, i9+3S (Qty. 4), i10+3D (Qty. 5).
Install Valve Actuators (page 19): Install the valve actuators on the valve assembly and
connect to the Personality board.
Install Temperature Sensors (page 20): Install the water and air sensors and connect the
cable plugs to the Personality board.
Install Heat Thermostat (page 21): Connect the heater thermostat cable plug to the Personality
board.
Connect the Transformer (page 21): Connect the transformer cable plug to the Personality
board.
Install the Indoor Control Panel (page 22): Wall-mount the Indoor Control Panel and connect
to the Personality board.
Install the MobileTouch Wireless Control Panel (page 26): Mount the transceiver and
connect to the Personality board.
Affixing the System Wiring Diagram Label (page 31): Affix the wiring diagram on the inside of
the front door of the Power/Load Center (for models i5S, i9+3S, i10+3D only).
Tools required
• 3/16 in. diameter drill (for mounting Indoor Control Panel).
• 5/16 in. diameter drill (for mounting Water Temperature Sensor).
1
2
3
4
5
6
7
8
9
10

9
IntelliTouch Personality Kit Installation Guide
Accessory Equipment
520142 i5X Expansion Kit five Auxiliaries.
520142 i10X Expansion Kit ten Auxiliaries.
520906 MobileTouch Wireless Control Panel and Transceiver.
520149 iS10+3 Ten-Function Spa-Side remote, Surface/recessed-mount faceplate, 150 ft. cable.
520355 Colored Faceplate Kit for surface-mount. Tan, Grey, or Black with label set.
520354 Colored Faceplate Kit for recessed-mount. Tan, Grey, or Black with label set.
520335 Mud box recessing iS10 into deck or tile.
520138 Indoor Control Panel, White.
520198 Two-Speed Three HP Relay up to three additional valve actuators.
520285 Valve module for controlling three additional actuators.
520106 Three HP Power Relay.
687000 Two Telephone remote control for any single circuit, usually Spa mode.
520148 QuickTouch Four-Function Wireless Remote Kit, Transmitter and Receiver.
520406 Dimmer Module. Supports up to 4,000 Watts maximum load (four dimmers handling
1,000 Watts each).

10
IntelliTouch Personality Kit Installation Guide
Plumbing Requirements
It is important that the pool and spa plumbing system be in accordance with local codes and the
Recommended Hydraulic Schematics (page 11, 12 and 13). Before starting, please review the
diagrams and the following recommended guidelines:
The spa should be at or above the level of the pool.
If the spa is attached to the pool, provide a dam between the two bodies of water to allow the spa
to overflow into the pool. If the spa is not attached to the pool, an overflow, sufficient in size to
carry a full pump-flow, must be installed at the water level in the spa.
Plumb a three-port Intake Valve on the suction-side of the filter pump, so that the center port of
the valve is connected to the pump inlet. Connect the spa suction to one side of the Intake Valve,
and the pool suction to the other side.
Plumb a three-port Return Valve on the return-side of the heater, so that the return water will
enter the valve through the center port.
Connect the spa return to one side of Return Valve, and the pool return to the other side.
If required, install a spa make-up line (consisting of a manual gate or ball valve, for elevated
spas install a check valve) to bypass the pool return line. This will enable some of the
chemically-balanced water from the pool to cycle through the spa. The manual valve will allow
the amount of bypass to be adjusted.
If the spa is to be constructed in concrete, special provision should be made at this time for the
installation of the Spa-Side remote Control.
Select a convenient location in the deck or above water level in the spa wall (where the
Spa-Side remote will not be submerged by the spa water), and install a 6 in. to 12 in. length of
one inch PVC pipe to provide a receptacle for the Spa-Side remote. The pipe should be level
and protrude beyond the finished surface of the spa. It will be cut back later at installation time.
Reduce the pipe size down to ½ in. or ¾ in. conduit, and run it to the proposed Load/Power
Center location at the equipment pad. Use sweep elbows for turns.
The Spa-Side remote will not be installed until the spa construction is completed.
For systems which incorporate a skimmer, it is possible to balance the amount of suction
between the skimmer and main drain for maintenance purposes. This is easily accomplished by
installing a manual three-port mixing valve at the suction line. Plumb one port to the skimmer and
the other to the main drain.
If a “non-booster pump” pressure-side pool cleaner is being used, plumb a manual three-port
valve between the filter pump and filter, with the third port plumbed to the pool cleaner line, and
install a motorized two-port Pool Cleaner Valve at this line. The motorized valve will
automatically open whenever the Control System activates the pool cleaner.
If a booster pump pool cleaner is being used, plumb the booster pump so that its suction-side is
connected to the pool return, after the heater, and as close to the ground as practical.
1
2
3
4
5
6
7
8

11
IntelliTouch Personality Kit Installation Guide
Recommended Hydraulic Schematic for Shared Equipment System
Plumb the solar feed and return lines between the filter and the heater. Install a three-port valve
at the feed line. Use a solar valve (model SOL-2T), to allow automatic draining of the panels.
A solar booster pump should be used when the distance to the panels exceed 200 ft., or the
panels are elevated higher than 25 ft.
Glazed solar panels require a drain valve (model HW-5B) to allow draining of the panels. This
prevents damage from overheating water. Install a drain valve at the solar feed line and connect
to the pool fill line.
Salt Chlorine Generator (SCG): IntelliChlor IC40 or IC20 salt chlorine generator cell with check
valve at the heater output. Refer to IntelliChlor User’s Guide (P/N 520589) for plumbing
requirements.
Equipment Location
All equipment, with the exception of the Spa-Side remote, must be located at least 10 ft. from the
water’s edge.
9
10
11
INTELLICHLOR®
MobileTouch® wireless remote controller
12

12
IntelliTouch Personality Kit Installation Guide
Recommended Hydraulic Schematic for Dual Equipment System
SOLAR
SENSOR
CLEANER
PUMP
CVA-24
HEATER
CVA-24
SOLAR
PUMP
VACUUM
RELIEF
WATER
SENSOR
SKIMMER
FILTER
PUMP FILTER
MAIN
DRAIN
HW-5B
WATERFALL
POOL
LIGHT
POOL
7
3
8
5
FREEZE
SENSOR
LOAD CENTER or POWER CENTER
SOLAR
SENSOR
HEATER
CVA-24
VACUUM
RELIEF
WATER
SENSOR
FILTER
PUMP FILTER
JET
PUMP
SPA-SIDE
REMOTE
AIR
INTAKE
SPA
LIGHT
SPA
1
2
11
46
MobileTouch® wireless remote controller
INTELLICHLOR®
2
2

13
IntelliTouch Personality Kit Installation Guide
Recommended Hydraulic Schematic for Single Body System
INTELLICHLOR®
2
INTELLICHLOR® SCG
CheckValve
MobileTouch® Wireless Controller
MobileTouch® Wireless Controller
IntelliTouch®,
EasyTouch®,SunTouch
Load/Power Center
TM
IntelliTouch®,
EasyTouch®,SunTouch
Load/Power Center
TM

14
IntelliTouch Personality Kit Installation Guide
High Voltage Connections
WARNING - It is required that the main power into the home be switched OFF at the main circuit
breaker box whenever the high voltage cover-panel is removed. The main power must also be
switched OFF to access the Power/Load Center enclosure low voltage raceway.
Power Center and Load Center Description
Power Center and Load Center enclosures are identical with the exception of the circuit breaker
base (Sub-panel). For details, refer to the Load Center illustration, see page 15. Not shown is the
high voltage cover-panel and the front door. See the WARNING information above before opening
the cover-panel.
Power Center (without Sub-panel)
The Power Center is connected to an electrical circuit breaker panel (Sub-panel) installed
at the equipment pad. The AC power is provided from the Main-panel (located at the house) to the
Sub-panel. The Power Center is installed next to the Sub-panel. For complete Power/Load Center
installation instructions, refer to the Load/Power Center User’s Guide (P/N 520100).
GFCI knockout
(approved rainproof
cover required)
Power Center Enclosure
(17” H x 17” W x 4.8” D)
Mounting bracket
Low voltage
compartment
High voltage
cover panel
attachment
screw holes
Power relays
Low voltage
raceway
Enclosure
Mounting bracket
Low voltage
circuit breakers
System
transformer
Outdoor control
panel attachment
screw holes
Grounding screw
terminals
Spring latch
Front door
removal screw
Auxiliary,
2-Speed Pump
(1-3) or Dimmer
relay locations