Interlogix Topaz ACURT2 Owner's manual

ACURT2 and ACURT4
Information Packet
Description:
Device Name:
Polling Address:
Serial Port Number:
Dial-Up Phone Number:
IP Address:
IP Router Address:
This information packet is for reference only.
See the TOPAZ Hardware Installation Guide
for complete instructions.
UTC Fire & Security
9 Farm Springs Road,
Farmington, CT 06034-4065
[phone]
www.UTCFireandSecurity.com
DO NOT REMOVE FROM CABINET

Copyright Copyright © 2010, UTC Fire & Security Inc. All rights reserved.
This document may not be copied or otherwise reproduced, in whole or in part, except
as specifically permitted under US and international copyright law, without the prior
written consent from UTC Fire & Security, 9 Farm Springs Road, Farmington, CT 06034-
4065.
Document number: 460951001D (December 2010).
Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT
NOTICE. UTC FIRE & SECURITY ASSUMES NO RESPONSIBILITY FOR
INACCURACIES OR OMISSIONS AND SPECIFICALLY DISCLAIMS ANY
LIABILITIES, LOSSES, OR RISKS, PERSONAL OR OTHERWISE, INCURRED AS A
CONSEQUENCE, DIRECTLY OR INDIRECTLY, OF THE USE OR APPLICATION OF
ANY OF THE CONTENTS OF THIS DOCUMENT. FOR THE LATEST
DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US ONLINE AT
WWW.UTCFIREANDSECURITY.COM.
This publication may contain examples of screen captures and reports used in daily
operations. Examples may include fictitious names of individuals and companies. Any
similarity to names and addresses of actual businesses or persons is entirely
coincidental.
Trademarks
and patents
Trade names used in this document may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Intended use Use this product only for the purpose it was designed for; refer to the data sheet and
user documentation. For the latest product information, contact your local supplier or
visit us online at www.utcfireandsecuritycom.
FCC
compliance
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
You are cautioned that any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.

iii
Table of contents
This packet includes information about:
DIP Switch SW1 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DIP Switch SW2 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DIP Switch SW3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rotary Switch SW4 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIP Switch SW5 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIP Switch SW6 (ACURT4 Only) . . . . . . . . . . . . . . . . . . . . . . 6
Clearing the Memory on the ACURT. . . . . . . . . . . . . . . . . . . . 7
Power-Up Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
On-Line Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
On-Line LED Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Battery Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ACURT2 and ACURT4 Component Layout . . . . . . . . . . . . . 11
Terminal Block TB1 connection information . . . . . . . . . . . . . 12
Terminal Block TB2 connection. . . . . . . . . . . . . . . . . . . . . . . 13
Terminal Block TB3 connection. . . . . . . . . . . . . . . . . . . . . . . 14
Terminal Block TB4 connection. . . . . . . . . . . . . . . . . . . . . . . 14
Terminal Block TB5 connection. . . . . . . . . . . . . . . . . . . . . . . 15
Terminal Block TB6 connection. . . . . . . . . . . . . . . . . . . . . . . 16
Terminal Block TB7 connection. . . . . . . . . . . . . . . . . . . . . . . 16
Terminal Block TB8 connection. . . . . . . . . . . . . . . . . . . . . . . 17
Terminal Block TB9 connection (ACURT4 only) . . . . . . . . . . 18
Terminal Block TB10 connection. . . . . . . . . . . . . . . . . . . . . . 19
Terminal Block TB11 connnection. . . . . . . . . . . . . . . . . . . . . 19
Terminal Block TB12 connection (ACURT4 Only). . . . . . . . . 20
Terminal Block TB13 connection (ACURT4 only) . . . . . . . . . 21
Terminal Block TB14 connection (ACURT4 only) . . . . . . . . 21
Terminal Block TB15 connection (ACURT4 only) . . . . . . . . . 22
Terminal Block TB16 connection (ACURT4 only) . . . . . . . . . 23
Terminal Block TB17 connection (ACURT4 only) . . . . . . . . . 23
Terminal Block TB18 connection (ACURT4 only) . . . . . . . . . 24

ACURT2 and ACURT4
Information Packet
iv

1
DIP Switch SW1 Settings
Note: See page 11 for switch location.
Switch
SW1
ON Position = Terminated – OFF Position = Not
Terminated
S1 Host TX Line Terminated
S2 Host RX Line Terminated
S3 Expansion Module Port TX Line Terminated
S4 Expansion Module Port RX Line Terminated
Current Switch Setting1
1. Circle the current setting
SW1 1234
OFF OFF OFF OFF
ON ON ON ON

ACURT2 and ACURT4
Information Packet
2
DIP Switch SW2 Settings
Note: See page 11 for switch location.
Switch
SW2 Switch Setting Function
S1
through
S3
S1 S2 S3 Host Communication Baud Rate
OFF OFF OFF 19200
ON OFF OFF 38400
OFF ON OFF 57600
ON ON OFF 1200
OFF OFF ON 115200
ON OFF ON 2400
OFF ON ON 4800
ON1
1. Indicates default setting
ON1ON19600
S4 OFF1Host Encryption disabled
ON Host Encryption enabled
S5
ON Dial-up Host Communications
OFF1Dedicated Host Communications
S6
ON Uses 5-wire RS-232 using RTS & CTS
OFF1Use RS-485 or 3-wire RS-232
S7 OFF1Spare – Set off
S8
ON Host Communication uses No Parity
OFF1Host Communication uses Even Parity

3
Current Switch Setting1
1. Circle the current settings
SW 2 12345678
OFF OFF OFF OFF OFF OFF OFF OFF
ON ON ON ON ON ON ON ON

ACURT2 and ACURT4
Information Packet
4
DIP Switch SW3 Settings
Note: See page 11 for switch location
Switch
SW3 Description
S1 OFF = LAN Disabled 1
ON = LAN Enabled
1. Indicates the default setting
S2 OFF = Do Not Allow LAN IP Parameters to be Updated 1,
ON = Allow LAN IP Parameters to be Updated
S3 OFF = Do Not Use LAN default IP Parameters 1
ON = Set IP Address To 192.168.0.132
S4 OFF = Triple DES Disabled 1,
ON = Triple DES Enabled
S5 Undefined, Leave OFF 1
S6 OFF = Wiegand or Proximity cards 1
ON = Magnetic Stripe Cards
S7 OFF = RAM Not Battery Backed Up
ON = RAM Battery Backed Up 1
S8 OFF = Watch Dog Timer Enabled 1
ON = Disable Watch Dog Timer
Current Switch Setting
SW 3 12345678
OFF OFF OFF OFF OFF OFF OFF OFF
ON ON ON ON ON ON ON ON

5
Rotary Switch SW4 Setting
DIP Switch SW5 Settings
Note: See page 11 for switch location
SW4
(rotary)
Function - Sets the ACURT polling
address Current Setting
0 - F Address 0-F
Note: See page 11 for switch location
SW5
ON POSITION = terminated – No Input
Device1
Off Position = Not Terminated – Zone In
Use
1. All termination is 1 kohm
Current
Setting
S1 Terminates Zone Input Reader 0 Zone 0
S2 Terminates Zone Input Reader 0 Zone 1 2
2. If the Exit Push Button is not connected, another 1kohm resistor must be
installed across the zone input
S3 Terminates Zone Input Reader 0 Zone 2
S4 Terminates Zone Input Reader 1 Zone 0
S5 Terminates Zone Input Reader 1 Zone 1 2
S6 Terminates Zone Input Reader 1 Zone 2

ACURT2 and ACURT4
Information Packet
6
DIP Switch SW6 (ACURT4 Only)
Note: See page 11 for switch location
SW6
ON POSITION = terminated – No Input Device1
Off Position = Not Terminated – Zone In Use
1. All termination is 1 kohm
Current
Setting
S1 Terminates Zone Input Reader 2 Zone 0
S2 Terminates Zone Input Reader 2 Zone 1 2*
2. If the Exit Push Button is not connected, another 1 kohm resistor must
be installed across the zone input
S3 Terminates Zone Input Reader 2 Zone 2
S4 Terminates Zone Input Reader 3 Zone 0
S5 Terminates Zone Input Reader 3 Zone 1 2
S6 Terminates Zone Input Reader 3 Zone 2