Interlogix TruVision HD-TVI 3MPX User manual

P/N 1073216-EN • REV C • ISS 03FEB17
TruVision HD
-TVI 3MPX
Camera Installation
Guide

Installation Guide 1
Contents
Introduction 2
Product overview 2
Installation 4
Installation environment 4
Package contents 5
Camera description 15
Mounting the TVI fixed lens bullet camera 20
Mounting the TVI VF motorized lens bullet
camera 26
Mounting the TVI fixed lens turret camera 32
Mounting the TVI VF motorized lens turret
camera 41
Specifications 50
Legal and regulatory information 52

2 Installation Guide
Introduction
Product overview
This is the installation guide for TruVision 3MPX
HD-TVI camera models:
HD-TVI fixed lens bullet camera:
TVB-2407 (3MPX Bullet, 3.6 mm lens, PAL)
TVB-4407 (3MPX Bullet, 3.6 mm lens, NTSC)
HD-TVI VF motorized lens bullet camera:
TVB-2408 (3MPX Bullet, 2.8 to12 mm lens, PAL)
TVB-4408 (3MPX Bullet, 2.8 to 12 mm lens,
NTSC)
HD-TVI fixed lens turret camera:
TVT-2401 (3MPX Turret, 2.8 mm lens, PAL)
TVT-4401 (3MPX Turret, 2.8 mm lens, NTSC)

Installation Guide 3
HD-TVI VF motorized lens turret camera:
TVT-2402 (3MPX Turret, 2.8 to 12 mm lens,
PAL)
TVT-4402 (3MPX Turret, 2.8 to 12 mm lens,
NTSC)

4 Installation Guide
Installation
This section provides information on how to install
the cameras.
Installation environment
When installing your product, consider these
factors:
•Electrical: Install electrical wiring carefully. It
should be done by qualified service personnel.
Always use a proper PoE switch or a 12 VDC UL
listed Class 2 or CE certified power supply to
power the camera. Do not overload the power
cord or adapter.
•Ventilation: Ensure that the location planned for
the installation of the camera is well ventilated.
•Temperature: Do not operate the camera
beyond the specified temperature, humidity or
power source ratings. The operating temperature
of the camera is between -30 to +60°C (-22 to
140°F). Humidity is below 90%.

Installation Guide 5
•Moisture: Do not expose the camera to rain or
moisture, or try to operate it in wet areas. Turn
the power off immediately if the camera is wet
and ask a qualified service person for servicing.
Moisture can damage the camera and also
create the danger of electric shock.
•Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle this product
will invalidate the warranty and may also result in
serious injury. Refer all servicing to qualified
service personnel.
•Cleaning: Do not touch the sensor modules with
fingers. If cleaning is necessary, use a clean
cloth with some ethanol and wipe the camera
gently. If the camera will not be used for an
extended period of time, put on the lens cap to
protect the sensors from dirt.
Package contents
Check the package and contents for visible damage.
If any components are damaged or missing, do not
attempt to use the unit; contact the supplier
immediately. If the unit is returned, it must be
shipped back in its original packaging.

6 Installation Guide
HD-TVI fixed lens bullet camera
Camera with power
and video output cable
harness (cables not
shown)
3 screws (4 ×
25 mm) and 3
anchors (7.5 ×
24.5 mm)
Mounting template Installation guide

Installation Guide 7
•12 VDC connector:
Two terminal
connector with
positive and negative
indicators
•Torx wrench
•CD •Equipment disposal
sheet
•Battery disposal sheet

8 Installation Guide
HD-TVI VF motorized lens bullet camera
Camera with power
and video output
cable harness (cables
not shown)
4 screws (4 ×
25 mm) and 4 (7.5 ×
24.5 mm) anchors
•Torx wrench
•Back box
•Video test cable •4 screws (M4.8 ×
18). Used with the
back box

Installation Guide 9
Mounting template
Ceiling Mounting
11
11
2
22
2
1:Screw Hole for
Bracket
2:Screw Hole for
Mounting Base
Installation guide
•CD
•Equipment disposal
sheet
•Battery disposal
sheet

10 Installation Guide
HD-TVI fixed lens turret camera
Camera with power
and video output
cable harness (cables
not shown)
•3 screws (4 ×25 mm)
and 3 anchors (7.5 ×
24.5 mm)
•12 VDC connector:
Two terminal
connector with
positive and negative
indicators
Mounting template

Installation Guide 11
•Adapter plate 4 screws (PM6-32 ×
10). Used to attach the
turret camera to a 2
Gang electrical box
4 screws (KM4 × 8).
Used to attach the
turret camera to the
bracket
3 screws (PM4 x 8).
Used to attach the
turret camera to the
adapter)
•CD Installation guide

12 Installation Guide
Equipment disposal
sheet
Battery disposal sheet
HD-TVI VF motorized lens turret camera
Camera with power
and video output cable
harness
3 screws (4 ×25
mm) and 3 anchors
(7.5 ×24.5 mm)
Template Installation guide

Installation Guide 13
•12 VDC connector:
Two-terminal
connector with positive
and negative indicators
Adapter plate
4 screws (KM4 x 8).
Used to attach turret
camera to bracket
4 screws (PM6-32
× 10). Used to
attach the turret
camera to a 2 Gang
electrical box
3 screws (PM4 x 8).
Used to attach the
turret camera to the
adapter)
•CD

14 Installation Guide
•Equipment disposal
sheet
•Battery disposal
sheet

Installation Guide 15
Camera description
Figure 1: HD-TVI fixed lens bullet camera
1. Selectable TVI or
960H output
2. 12 VDC power
3. Mounting base
4. Camera body
5. Lens
6. IR LEDs
7. HD-TVI (wires
disconnected) /
960H (wires
connected
together) selection

16 Installation Guide
Figure 2: HD-TVI VF motorized lens bullet
camera
Note: When making adjustments to the motorized lens
bullet, it is important to make sure that the access cover for
the area that contains the video test cable connector, OSD
menu button, and the 960H/TVI selection switch is properly
tightened to prevent leakage. The access cover should be
rotated until it is tight, up against the camera body.
1. Lens
2. Selectable TVI or
960H output
3. 12 VDC/24 VAC
power
4. Camera body
5. Sunshield
6. Mounting base
7. Access to 960H or
TVI selection
switch

Installation Guide 17
1. Video test cable
2. OSD menu button
3. 960H/TVI
selection switch
Note: When making adjustments to the motorized lens
bullet, it is important to make sure that the access cover for
the area that contains the video test cable connector, OSD
menu button, and the 960H/TVI selection switch is properly
tightened to prevent leakage. The access cover should be
rotated until it is tight, up against the camera body.

18 Installation Guide
Figure 3: HD-TVI fixed lens turret camera
1. Trim ring
2. Housing
3. Base
4. Lens assembly
5. 12 VDC power
6. Selectable TVI or
960H output
7. HD-TVI (wires
disconnected) /
960H (wires
connected
together) selection