Interlogix TruVision TVB-6102 User manual

P/N 1073685-EN • REV B • ISS 26NOV19
TruVision HD
-TVI Bullet
Camera
Installation Guide

Installation Guide 1
Contents
Product overview 2
Package contents 3
Camera description 10
Installation 14
Installation environment 14
Mounting the HD-TVI fixed lens bullet
camera (TVB-6102, TVB-6104) 16
Mounting the HD-TVI VF motorized lens
bullet camera (TVB-6101, TVB-6103,
TVB-6105, TVB-6106) 19
Mounting the HD-TVI fixed lens low light
bullet camera (TVB-6107) 24
Specifications 27
Contact information and manuals /
firmware 29
Legal and regulatory information 29

2 Installation Guide
Product overview
This is the installation guide for TruVision
HD-TVI bullet camera models:
HD-TVI fixed lens bullet camera:
TVB-6102 (2MPxBullet, 3.6 mm lens)
TVB-6104 (5MPxBullet, 3.6 mm lens)
HD-TVI VF motorized lens bullet
camera:
TVB-6101 (720P Bullet, 2.7 to 13.5 mm
lens)
TVB-6103 (2MPxBullet, 2.7 to 13.5 mm
lens)
TVB-6105 (5MPxBullet, 2.7 to 13.5 mm
lens)
TVB-6106 (8MPxBullet, 2.7 to 13.5 mm
lens)
HD-TVI fixed lens low light bullet
camera:
TVB-6107 (2MPxBullet, 3.6 mm lens)

Installation Guide 3
Go to “Contact information and manuals” on
page 29 for information on where to
download the configuration manual for these
cameras.
Package contents
Check the package and contents for visible
damage. If any components are damaged or
missing, do not attempt to use the unit; contact
the supplier immediately. If the unit is returned,
it must be shipped back in its original
packaging.

4 Installation Guide
HD-TVI fixed lens bullet camera (TVB-
6102, TVB-6104)
Camera with
power and video
output cable
harness (cables
not shown)
3 screws and 3
anchors
Mounting
template
Installation guide

Installation Guide 5
•12 VDC
connector: Two
terminal
connector with
positive and
negative
indicators
•Torx wrench
•Equipment
disposal sheet

6 Installation Guide
HD-TVI VF motorized lens bullet
camera (TVB-6101, TVB-6103, TVB-
6105, TVB-6106)
Camera with
power and video
output cable
harness (cables
not shown)
4 screws and 4
anchors for the
camera
•3 screws and 3
anchors. Used
with the back box
4 screws to
connect the
camera to the
back box

Installation Guide 7
•Torx wrench
•Back box
(included with
camera)
•4 screws. Used
with the back box
•Mounting
template
Installation guide
•Equipment
disposal sheet

8 Installation Guide
HD-TVI fixed lens low light bullet
camera (TVB-6107)
Camera with
power and video
output cable
harness (cables
not shown)
3 screws and 3
anchors
Mounting
template
Installation guide

Installation Guide 9
•12 VDC
connector: Two
terminal
connector with
positive and
negative
indicators
•Torx wrench
•
Equipment
disposal sheet

10 Installation Guide
Camera description
Figure 1: HD-TVI fixed lens bullet camera (TVB-
6102, TVB-6104)






1. TVI/960H analog
switch button
2. 12 VDC power
3. TVI output
4. Mounting base
5. Camera body
6. Lens

Installation Guide 11
Figure 2: HD-TVI VF motorized lens bullet
camera (TVB-6101)







1. TVI output
2. 12 VDC/24 VAC
power
3. TVI/960H analog
(connect wires to
switch to 960H
analog)
4. Mounting base
5. Sunshield
6. Lens
7. Camera body

12 Installation Guide
HD-TVI VF motorized lens bullet camera (TVB-
6103, TVB-6105, TVB-6106)







1. TVI output
2. 12 VDC/24 VAC
power
3. TVI/960H analog
switch button
4. Mounting base
5. Sunshield
6. Lens
7. Camera body

Installation Guide 13
Figure 7: HD-TVI fixed lens low light bullet
camera (TVB-6107)






1. Lens
2. Camera body
3. Mounting base
4. TVI output
5. 12 VDC power
6. TVI/960H analog
switch button

14 Installation Guide
Installation
This section provides information on how to
install the cameras.
Installation environment
When installing your product, consider these
factors:
•Electrical: Install electrical wiring carefully.
It should be done by qualified service
personnel. Always use a proper 12 VDC
UL listed Class 2 CE certified power supply
or a proper 24 VAC power supply,
depending on the camera. Do not overload
the power cord or adapter.
•Ventilation: Ensure that the location
planned for the installation of the camera is
well ventilated.
•Temperature: Do not operate the camera
beyond the specified temperature, humidity
or power source ratings. The operating
temperature of the camera is between -40

Installation Guide 15
to + 60°C (-40 to 140°F). Humidity is below
90%.
•Moisture: Do not expose the camera to
rain or moisture, or try to operate it in wet
areas. Turn the power off immediately if
the camera is wet and ask a qualified
service person for servicing. Moisture can
damage the camera and also create the
danger of electric shock.
•Servicing: Do not attempt to service this
camera yourself. Any attempt to dismantle
this product will invalidate the warranty and
may also result in serious injury. Refer all
servicing to qualified service personnel.
•Cleaning: Do not touch the sensor
modules with fingers. If cleaning is
necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the
camera will not be used for an extended
period of time, put on the lens cap to
protect the sensors from dirt.

16 Installation Guide
Mounting the HD-TVI fixed lens
bullet camera (TVB-6102, TVB-
6104)
Surface mount
1. Place the provided template level against
the mounting surface and mark the
position of the mounting holes.
template
2. Following all local safety regulations, drill
and prepare the mounting and cable
access (if required) holes.
3. Route the cables through the cable
access hole.
4. Secure the camera to the surface with
the mounting hardware that was
provided.

Installation Guide 17
5. Connect the corresponding cables.
Power up the camera to check if the
monitor displays the desired view.
6. Adjust the camera to get the best viewing
angle. See the figure below.



R: 360°
P: 360°
T: 180°

18 Installation Guide
a) Loosen the P disk (1) to adjust the
pan direction [0-360°]. Tighten after
completing the adjustment.
b) Loosen the T screw (2) to adjust the
tilt direction [0-180°]. Tighten the
screw after completing the
adjustment.
c) Loosen the R screw (3) and rotate
the camera [0-360°] to adjust the lens
to the desired surveillance angle.
Tighten the screw after completing
the adjustment.
7. Tighten the locking screws and the trim
ring to position the camera in place.