Interlogix TVD-6120VE-2-N User manual

© 2012 UTC Fire & Security. All rights reserved. 1 / 2 P/N 1072542B-EN • ISS 21JUN12
TVD-6120VE-2 / TVD-6125VE-2 Camera Quick
Start Guide
Introduction
This is the Quick Installation Guide for the TVD-6120VE-2-N(-
P)/ TVD-6125VE-2-N(-P) color dome camera.
Refer to the user manual for complete instructions on installing
and configuring this camera.
User guidelines
• Program the camera settings as much as possible before
mounting the camera. Take appropriate safety precautions
while completing programming after installation.
• Always use a 12 VDC or 24 VAC UL listed Class 2 power
supply to power the camera.
• Do not use the camera over the temperature range
specifications: -10°C to +50°C (14°F to 122°F)
• If the light source where the camera is installed
experiences rapid, wide- variations in lighting, the camera
may not operate as intended.
WARNING: To reduce the risk of fire or electronic shock, do
not expose the camera to rain or open the back of the camera.
Description
Figure 1: Camera description

1. Dome cover
2. Screw hole
3. Base
4. OSD control button
5. Lens
6. IR LED
7. IR LED cover
8. Outlet hole
9. Power supply and video
BNC cables
10. Composite video BNC cable
11. Focus adjustment
12. Zoom adjustment
Installation
Please check the package contents and make sure that the
device in the package is in good condition and all the assembly
parts are included.
Note: Before installing, please ensure that the mounting
surface is strong enough to withstand three times the weight of
the camera. If the wall is not strong enough, the camera may
fall and cause serious damage.
Install the camera
1. Remove the dome cover (see Figure 1).
2. Secure the camera to the mounting surface with screws.
3. Connect a 12 VDC or 24 VAC power supply to the power
input and connect a coaxial cable from the camera’s BNC
connector to a CCTV monitor or video recording device.
4. Adjust the lens:
Remove the IR LED cover to adjust the lens and the
viewing angle.
Rotate the panning table to adjust the panning position of
the camera.
Lens rotation 0-355°
Tilting table 0-75°
Panning table 0-355°
Rotate the tilting table to adjust the tilting position of the
camera.
Rotate the lens to adjust the azimuth angle of the image.
Adjust the lens to obtain the appropriate angle of view and
the optimum focus. Tighten the focus lock lever.
5. Replace the IR LED and dome covers on the camera.
6. Secure the dome cover with screws.
Note: Ensure that the screws have been tightened securely to
prevent water seepage.

2 / 2 P/N 1072542B-EN • REV 0.05 • ISS 21JUN12
Programming
Once the camera hardware has been installed, it can then be
configured. Program the camera by attaching a standard video
monitor to the system. Press Enter on the camera’s menu
control button to display the Setup menu (see Figure 2).
OSD control button
The on-screen display (OSD) control button (see Figure 1) is a
five-direction joystick that lets you manually control the camera
functions. Table 1 below lists the OSD control button functions
and describes their use.
Table 1: Description of the OSD control button
Button
direction
Description
Up Moves the cursor upward to select an item
Left Moves the cursor left to select or adjust the
parameters of the selected item.
Right Moves the cursor to the right to select or adjust
the parameters of the selected item.
Down Moves the cursor downward to select an item.
Enter Press the center of the control pad to display the
Setup menu. If the selected item has its own
menu, press the control pad to enter a submenu.
Using the Setup menu
The Setup menu provides access to the camera configuration
options.
Figure 2: Setup menu screens
Menu item Description
Lens Defines the camera ID, mirror, and digital noise
reduction (DNR) set up.
Shutter/AGC Defines the method of iris control.
White Bal Defines the white balance (WB) set up.
Backlight Defines the highlight compensation (HLC) and
backlight compensation (BLC) set up.
Pict Adjust Defines the image quality functions.
ATR Defines the adaptive tone-curve reproduction set up.
Motion Det Defines the motion detection set up.
Privacy Defines privacy mask set up.
Day/Night Defines the day/night (D/N) set up.
NR Defines the digital noise reduction level.
Camera ID Defines the camera ID displayed on-screen.
Sync Displays the current synchronization mode.
Language Defines the language of the OSD.
Camera Reset Resets the camera to factory default settings.
Save All Saves changes made.
Menu item Description
Exit Exits the menu and returns to live mode.
To access the Setup menu:
1. Press the OSD control button to access the Setup menu
and its submenus.
2. Push the button up/down to move between menu options.
3. Push the button left/right to select an option.
4. Select Next to move to the next Setup menu screen and
Back to return to the previous Setup menu screen.
5. When in a sub menu, select Return to return to the
previous menu.
6. To save configuration changes, select Save All and press
Enter.
7. To exit the Setup menu and return to live mode, move the
cursor to Exit at the bottom of the screen and press Enter.
Specifications
Model TVD-6120VE-2-N(P) TVD-6125VE-2-N(P)
Power supply 24 VAC / 12 VDC 24 VAC / 12 VDC
Current 290mA 375mA
Power consumption Max. 3.5 W Max. 4.5 W
Operating
temperature
-10 to +50 °C (14 to 122 F°)
Weight 800 g (1.76 lbs)
Dimensions (H × Ø) 100 × 140 mm
Menu map
