Interlogix TruVision Series User manual

TruVision
IP Compact
PTZ Camera
Installation
Guide
P/N 1073406-EN • REV C • ISS 23MAY18

Copyright
© 2018 United Technologies Corporation,
Interlogix is part of UTC Climate, Controls &
Security,
a unit of United Technologies Corporation.
All rights reserved.
Trademarks and
patents
Trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacturer
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA
92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
FCC compliance
Class A: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
FCC conditions
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This Device must accept any interference
received, including interference that may cause

undesired operation.
ACMA compliance
Notice!
This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be required
to take adequate measures.
Canada
This Class A digital apparatus complies with CAN
ICES-003 (A)/NMB-3 (A).
Cet appareil numérique de la classe A est conforme
à la norme CAN ICES-003 (A)/NMB-3 (A).
European Union
directives
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2013/56/EU &2006/66/EC (battery directive): This
product contains a battery that cannot be disposed
of as unsorted municipal waste in the European
Union. See the product documentation for specific
battery information. The battery is marked with this
symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier
or to a designated collection point. For more
information see: www.recyclethis.info.

Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE
TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT ANY
PERSON OR ENTITY BUYING ITS PRODUCTS,
INCLUDING ANY “AUTHORIZED DEALER” OR
“AUTHORIZED RESELLER”, IS PROPERLY
TRAINED OR EXPERIENCED TO CORRECTLY
INSTALL FIRE AND SECURITY RELATED
PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
www.firesecurityproducts.com/policy/product-
warning/ or scan the following code:
Contact
information and
manuals/ tools/
firmware
For contact information and to download the latest
manuals, tools, and firmware, go to the web site of
your region.
Americas: www.interlogix.com
EMEA: www.firesecurityproducts.com
Manuals are available in several languages.
Australia/New Zealand: www.utcfs.com.au

Installation Guide 1
Content
Introduction 2
Product overview 2
Contact information and manuals/tools/firmware 2
Installation 3
Installation environment 3
Package contents 4
Camera description 9
IR illuminators 15
Alarm input and output connections 16
Mounting the TVP-5101 PTZ camera 17
Mounting the TVP-5102 PTZ camera 24
Mounting the TVP-5103 PTZ camera 31
Using the camera with an Interlogix NVR or Hybrid DVR or
another system 42
Using the camera with a TruVision Navigator 42
Accessing the camera over the internet 42
Specifications 44
TruVision TVP-5101 indoor IR IP PTZ camera 44
TruVision TVP-5102 IR IP PTZ camera 44
TruVision TVP-5103 IR IP PTZ camera 45
Pin definitions 46

2 Installation Guide
Introduction
Product overview
This is the installation guide for TruVision IP Compact PTZ
Camera models:
TVP-5101 (2.0 MPX, 4X, 350 degree, 20m IR,
H.264/H.265)
TVP-5102 (2.0 MPX, 20X, 150m IR, H.264/H.265)
TVP-5103 (3.0 MPX, 20X, 50m IR, H.264/H.265)
The Configuration manual is available on our web site.
Contact information and
manuals/tools/firmware
For contact information and to download the latest manuals,
tools, and firmware, go to the web site of your region.
Americas:
www.interlogix.com
EMEA: www.firesecurityproducts.com
Manuals are available in several
languages.
Australia/
New Zealand:
www.utcfs.com.au

Installation Guide 3
Installation
This section provides information on how to install the
cameras.
Installation environment
When installing your product, consider these factors:
The TVP-5101 or TVP-5103 were not designed to be mounted
flat to a wall. They should be mounted to a ceiling. If mounted
to a wall, the wall mount should be used. The bubble/lens
assembly should be pointing towards the ground.
•Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC or 24 VAC (depending on the
camera) UL listed Class 2 or CE certified power supply to
power the camera. Do not overload the power cord or
adapter.
•Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
•Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
The operating temperature of the camera without heater
is between -30 to +60°C (-22 to 140°F). Humidity is below
90%. For the outdoor cameras that feature built-in
heaters, the operating temperature range is -40 to 60°C
(-40 to140°F)
•Moisture: Do not expose the camera to rain or moisture
or try to operate it in wet areas. Turn the power off
immediately if the camera is wet and ask a qualified
service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.

4 Installation Guide
•Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.
•Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
TVP-5101 indoor IR PTZ camera
•Camera
•Screws:
Drywall anchor
7.5 × 24.5 mm (3 pcs)
Screw
PA4 × 25 mm (3 pcs)

Installation Guide 5
•Water joint: Provides
water resistance to
network cable
connector.
•Drill template
•Installation guide •CD with Configuration
manual and TruVision
Device Manager
•Equipment Disposal
sheet
•Battery Disposal sheet

6 Installation Guide
TVP-5102 IR PTZ camera
•Camera •Water joint: Provides
water resistance to
network cable
connector.
•Installation guide •CD with
Configuration manual
and TruVision Device
Manager
•Equipment Disposal
sheet
•Battery Disposal
sheet