Interlogix ACL870FL-BS User manual

© 2018 United Technologies Corporation. P/N 1073516A• REV 01.01 • ISS 27AUG18
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights reserved.
ACL870FL-BS - Standalone Biometric Reader -
Installation Instructions
Description / Operation
ACL870FL-BS is access control fingerprint reader designed for
easy management of the users and configuration. The scanner
is made with advanced capacitive sensing technology that
provides some advantages over optical solutions like:
- making almost impossible to make fake copy of the users
fingers
- same performance in the different light conditions
- good reading of fingers with stains from daily jobs
Built in strong scanning and matching algorithm provides
excellent tolerance in the way finger is swiped over the sensor
reducing to minimum the need to repeat finger swiping at the
sensor.
The reader can store up to 99 finger templates. One template
is reserved for user manager (Administrator), one template is
reserved for reader configuration (Installer) and up to 97
templates are for Users.
Mounting
Figure 1: Mounting instructions
•Do not install the device and cabling close to a source of
strong electro-magnetic fields like radio-transmitting antenna.
•Do not place the device near or above heating equipment.
•If cleaning, do not spray or splash water or other cleaning
liquids but wipe it out with smooth cloth or towel.
•Do not let children touch the device without supervision.
•Note that if the sensor is cleaned by detergent, benzene or
thinner, the surface will be damaged and the fingerprint can't
be entered.
Specifications
Fingerprint Capacity:
97 templates
Output:
1 x Relay (2 A at 24V AC/DC)
Push Button Input:
Yes
Door Open Time:
Pulse (1 to 30 seconds) or Toggle(ON/OFF)
Entry Mode:
Finger (basic installation)
Finger or Card (when used with card reader)
Finger or PIN code (when used with keypad)
Programming:
By swiping
Admin/Installer Fingers
1 Administrator and 1 Installer finger
Backlight ON/OFF:
Yes
Buzzer ON/OFF:
Yes
Tamper
Yes, activated on frame removal
Firmware upgrade:
via RS485 converter and windows application
Current Consumption:
100 mA max.
Power Supply:
9 to14 V DC
Indication:
Tricolor Status LED
IP Factor:
IP40
Storage/Operating
Temperature :
-20 to +50°C
Storage/Operating
Humidity:
5 to 93% noncondensing
Dimensions
80 x 80 x 9 mm
Application diagram
Figure 2: Application diagram
ACL870FL-BS
Outside
Secured Area
ACL800FL-RU2
ACL870FL-PB
ACL870SU-PB

2 / 9 P/N 1073516A• REV 01.01 • ISS 27AUG18
ACL800FL-RU2 : Optional) 2 Relay Remote Unit
ACL870FL-PB (Optional): 2 Relay Remote Unit and request-to-
exit Button
ACL870SU-PB (Optional) : 1 Relay Remote Unit and request-
to-exit Button
Wiring
Figure 3: Wiring
Recommended swiping technique
Figure 4: Swiping technique
Follow the below instructions for correct finger swiping. Starting
from the first finger joint, place the selected finger on the swipe
sensor and move it evenly downwards in one steady
movement.
Result:
For a valid swipe: Tricolour Status LED turns green + OK
beep(short + long beep)
For an invalid or misread swipe: Tricolour Status LED turns red
+ error beep ( 3 short beeps)
Indication
Adding admin finger
1
Close the jumper on the back of the
device
2
Reset the Power of the device
12/24VAC/DC
3
Wait for One long + multiple short
beeps
4
Open the jumper. (short beeps will
stop)
5
Wait for about 15 seconds for the LED
to blink in Orange
6
Swipe the Master finger min.6 times.
(Until Ok Beep)
Warning:
•This procedure also deletes all the users and the installer
finger.
•This procedure will unpair the connected relay unit
(ACL870SU-PB, ACL870FL-PB or ACL800FL-RU2)
Pairing - biometric reader and remote relay
unit
If secure installation is needed, the reader can be connected to
remote relay unit at secured area, which also can play the role
of request-to-exit push button. Follow the instructions bellow to
pair (couple) both devices or refer to the Remote Relay’s
Manual.
Pairing ACL870FL-BS with ACL870FL-PB
Figure 5: Wiring
1. Close the jumper. ACL870FL-PB beeps continuously and
the red led blinks.
2. Open the jumper.
3. Wait for beep + OK beep (short + short + long beep)
After the OK beep, the coupling is done.
Relay Output
Jumper (Adding Master Finger)
Connection to additional
card reader or keypad
Electric
Door
Strike
(DC
powered)
Tricolor Status LED :
Green - Access Granted
Red - Access denied
Orange - Idle Mode
OK Beep - short + long beep
Error Beep - 3 short beeps
Swipe Finger - 2 short beeps

P/N 1073516A• REV 01.01 • ISS 27AUG18 3 / 9
Pairing ACL870FL-BS with ACL870SU-PB
Figure 6: Wiring
1. Put dipswitch No.1 to position ON. ACL870SU-PB beeps
continuously and the red led blinks.
2. Put dipswitch No.1 to position OFF.
3. Wait for beep + OK beep (short + short + long beep)
After the OK beep, the coupling is done.
Pairing ACL870FL-BS with ACL800FL-RU2
Figure 7: Wiring
1. Put the jumper to closed position. ACL800FL-RU2 beeps
continuously and the red led blinks.
2. Put the jumper to open position.
3. Wait for beep + OK beep (short + short + long beep)
After the OK beep, the coupling is done.
Warning: Changing the ADMIN finger will also unpair the
remote relay unit.
Administrator programming
Use point fingers as Administrator and Installer. You can use the other fingers as access fingers. Administrator finger is enrolled at
the end of the system installation. Initial enrollment of the Admin finger is described in installer manual
Figure 8: Finger
ADD Finger Relay 1 (Finger that will activate relay 1)
Action
Finger
Backlight
Buzzer Sound
Swipe Admin Finger 1 time
X 1
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
short beep
Swipe User Finger min. 6 times
(until short + long beep)
X 6
Fast blinking
short + long beep
or
Present card/tag 1 time
fast blinking
short + long beep
ADD Finger Relay 2 (Finger that will activate relay 2)
Action
Finger
Backlight
Buzzer Sound
Swipe Admin Finger 2 times
X 2
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
short beep
Swipe User Finger min. 6 times
(until short + long beep)
X 6
fast
blinking
short + long beep
or
Present card/tag 1 time
fast blinking
short + long beep
INSTALLER
RIGHT
ADMIN
LEFT

4 / 9 P/N 1073516A• REV 01.01 • ISS 27AUG18
Relay 2 is available if the reader is used with remote relay unit with 2 relays (ACL870FL-PB and ACL800FL-RU2). Consult the
installer if Relay 2 is available in your system.
ADD Finger Relay 1&2 (Finger that will activate relay 1&2)
Action
Finger
Backlight
Buzzer Sound
Swipe Admin Finger 3 times
X 3
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
short beep
Swipe User Finger min. 6 times
(until short + long beep)
X 6
fast
blinking
short + long beep
or
Present card/tag 1 time
fast blinking
short + long beep
Relay 2 is available if the reader is used with remote relay unit with 2 relays (ACL870FL-PB and ACL800FL-RU2). Consult the
installer if Relay 2 is available in your system.
DELETE Finger
Action
Finger
Backlight
Buzzer Sound
Swipe Admin Finger 4 times
X 4
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
short beep
Swipe User Finger
X 1
fast
blinking
short + long beep
or
Present card/tag 1 time
fast blinking
short + long beep
DELETE ALL Fingers and Cards
Action
Finger
Backlight
Buzzer Sound
Swipe Admin Finger 4 times
X 4
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
slow
blinking
short beep
Swipe Admin Finger 2 times
X 2
fast
blinking
multiple beeps
CHANGE ADMIN Finger
Action
Finger
Backlight
Buzzer Sound
Swipe Admin Finger 5 times
X 5
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
slow
blinking
short beep
Swipe NEW Admin Finger
min.6 times
X 6
fast
blinking
short + long beep
CHANGE INSTALLER Finger
Action
Finger
Backlight
Buzzer Sound
Swipe Admin Finger 6 times
X 6
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
slow
blinking
short + long beep
Swipe NEW Installer Finger
min.6 times
X 6
fast
blinking
3 short beeps
Connecting ACL870FL-BS with ACL800FLW proximity reader

P/N 1073516A• REV 01.01 • ISS 27AUG18 5 / 9
Connect both devices with the cable provided. The proximity reader will be powered via that cable. No extra power supply for the
proximity reader is needed. Once connected, no further settings are needed.
Administrator Programming block diagram
Swipe the ADMIN Finger 1 to 6 times depending of the desired menu
Installer programming
Set Relay 1 Time
Action
Finger
Backlight
Buzzer Sound
Swipe Installer Finger 1 time
X 1
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
short beep
Swipe the INSTALLER Finger
and start counting seconds
X 1
fast
blinking
beeps on 1 second
Swipe the INSTALLER Finger
to stop or wait 30 seconds to
put the relay in toggle mode
X 1
fast
blinking
short + long beep
Set Relay 2 Time
Action
Finger
Backlight
Buzzer Sound
Swipe Installer Finger 2 times
X 2
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
short beep
Swipe the INSTALLER Finger
and start counting seconds
X 1
fast
blinking
beeps on 1 second
Swipe the INSTALLER Finger
to stop or wait 30 seconds to
put the relay in toggle mode
X 1
fast
blinking
short + long beep
Relay 2 is available if the reader is used with remote relay unit with 2 relays (ACL870FL-PB and ACL800FL-RU2). Consult the installer if Relay 2 is
available in your system.
BUZZER ON/OFF
Action
Finger
Backlight
Buzzer Sound
Swipe Installer Finger 3 times
X 3
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
short beep
Only in combination with
ACL870FL-PB andACL800FL-RU2

6 / 9 P/N 1073516A• REV 01.01 • ISS 27AUG18
Swipe Installer Finger
X 1
fast
blinking
short + long beep
BACKLIGHT ON/OFF
Action
Finger
Backlight
Buzzer Sound
Swipe Installer Finger 4 times
X 4
slow
blinking
short beep
Wait 5 seconds (until fast blinking)
short beep
Swipe Installer Finger
X 1
fast
blinking
short + long beep
Installer Programming block diagram
Swipe the Installer Finger 1 to 4 times depending of the desired menu
Administrator programming by keypad
Programming by keypad can be done only if the ACL870FL-BS reader is connected to keypad ACL805FLW as shown in the
pictures bellow. The connection is done by the cable provided with the biometric reader. Once connected, the keypad must be put
in slave mode.
Connect both devices with the cable provided.
Only in combination with
ACL870FL-PB andACL800FL-RU2

P/N 1073516A• REV 01.01 • ISS 27AUG18 7 / 9
Put the keypad in slave mode:
Press B (3 seconds) + 000000
Press 0
Press 2
Press A to exit
Reset the device
Note: In some previous versions of our keypads, you can enter the menu only by pressing B + 000000. Please refer to the
Keypad’s Manual.
Administrator programming by keypad
Note: The Fingerprint can be deleted by keypad,
only if it is enrolled with keypad.
Example 1: Add user finger to Relay1 - Press 1234 + A + 1 + 1 + 1 + 01 + A + Enroll finger 6 times. 0A to exit.
Example 2: Add user PIN 147 to Relay2 - Press 1234 + A + 1 + 2 + 2 + 02 + A + 147 + A. 0A to exit.
Note: Entering this menu is done
by admin PIN Code. You cannot
enter with Admin Finger.

8 / 9 P/N 1073516A• REV 01.01 • ISS 27AUG18
Installer programming by keypad
Example: Change relay1 time to 2 seconds - 5678 + A + 1 + 02 + A.
Note: Entering this menu is done by
installer PIN code. You cannot enter
with Installer Finger.

P/N 1073516A• REV 01.01 • ISS 27AUG18 9 / 9
Regulatory information
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
European Union
directives
This product and - if applicable - the supplied
accessories too are marked with "CE" and
comply therefore with the applicable harmonized
European standards listed under the EMC
Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
2013/56/EU & 2006/66/EC (battery directive):
This product contains a battery that cannot be
disposed of as unsorted municipal waste in the
European Union. See the product documentation
for specific battery information. The battery is
marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated
collection point. For more information see:
www.recyclethis.info.
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR
SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
www.firesecurityproducts.com/policy/product-
warning/ or scan the following code:
Contact
information and
manuals
For contact information go to: www.interlogix.com
or www.firesecurityproducts.com
To get translations for this and other product
manuals go to: www.firesecurityproducts.com