Intermatic Home Settings HA01 Technical specifications

Installation and Programming Instructions
1 – Wire and Install the HA01 In-Wall Receptacle
Electrical shock hazard. Risk of injury or death. Remove electrical
power at service panel before installing.
Follow local electrical codes during installation.
For indoor use only.
This device is not a GFCI receptacle and must not be used to replace a
GFCI receptacle, nor be used in any location where a GFCI receptacle
is required, including outdoor installations unless protected by an
upstream GFCI that is in good working order.
•
•
•
•
WARNING
With HomeSettings devices, you can reliably and remotely
control your lighting and appliances. The outstanding features
of the HomeSettings HA01 In-Wall Receptacle include:
Two Receptacles—one standard outlet and one Z-Wave™
controlled outlet
NOTE: Both outlets will also work as standard outlets.
Wireless signal reliability—each HomeSettings product has a
special feature that virtually guarantees that wireless signals
are received
Feedback that will allow you to see whether your device has
received the ON/OFF signal
Ease of installation
Replaces a standard receptacle
Because the HA01 In-Wall Recep-
tacle is a Z-Wave device, it is com-
patible with any HomeSettings
network, other Z-Wave networks,
and all HomeSettings or other
Z-Wave devices displaying the
Z-Wave logo, regardless of manufacturer.
Each module in a Z-Wave network communicates with every
other module, acting as a “repeater” and routing your com-
mands to their destination by the most reliable pathway. When
Z-Wave devices (regardless of manufacturer) are installed
throughout the house, signals are automatically routed around
obstacles or dead spots, strengthening the network as more
devices are added.
•
•
•
•
•
Thank you for purchasing an Intermatic HomeSettings device
Wire the HA01 In-Wall Recep-
tacle according to the wiring
diagram shown here, and the
instructions below.
Turn off power at the ser-
vice panel by REMOVING
FUSE or TURNING THE
CIRCUIT BREAKER OFF.
Remove existing re-
ceptacle from the box if
necessary.
Trim building wires to 7/16”.
Connect the BLACK wire of the HA01 to the hot build-
ing wire (the wire leading to the circuit breaker or
fuse box), using a twist connector (provided).
NOTE: Twist connectors provided are suitable for
copper wire only. For aluminum wire, consult an
electrician.
NOTE: Insert wires straight into twist connector,
then twist clockwise. Make sure all twist connectors
are tight. Secure each twist connector with electri-
cal tape. Make sure no bare wire shows below the
wire connector.
Connect the WHITE wire of the HA01 to the neutral wire,
using a twist connector (provided).
Connect the ground wire from the box to the bare copper
wire on the HA01 In-Wall Receptacle. If there is no ground
wire, ground the HA01 unit to the box. If the box is plastic,
connect the bare copper wire to ground as supplied or con-
tact an electrician.
Tuck the wires into the wall box leaving room for the HA01
unit.
Using screws provided, mount the HA01 unit to the wall
box, then install the decorator wall plate (not provided).
Turn power back on at the service panel.
Plug a lamp or appliance into the receptacle marked
“SWITCHED”.
Turn the knob or switch on the lamp or appliance to the ON
position.
To manually turn ON the
HA01 In-Wall Receptacle,
press and release the ON/
OFF/PROGRAM button. The
green LED indicator will turn
ON, and the lamp or appli-
ance plugged into the HA01
switched receptacle will also
turn ON.
To manually turn OFF the
HA01 In-Wall Receptacle,
press and release the ON/OFF/
PROGRAM button. The green
LED indicator will turn OFF,
and the lamp or appliance
plugged into the HA01 switched receptacle will also turn
OFF.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
•
•
BLACK WIRE
(HOT)
125VAC @ 50/60 HZ
WHITE WIRE
(NEUTRAL)
GROUND WIRE
BARE
COPPER
In-Wall Receptacle
MODEL HA01
Our products are constantly evolving. To see if advanced functionality is
possible with your product, look it up at www.homesettings.com.
Understand basic wiring principles and techniques (IF NOT, USE A
QUALIFIED ELECTRICIAN FOR THIS INSTALLATION.)
Can interpret wiring diagrams
Have circuit-wiring experience
Read all instructions and documentation and save for future reference
Are prepared to test your work, making sure you have wired the recep-
tacle according to your local electrical code
•
•
•
•
•
Before installing, make sure that you…
GREEN LED
INDICATOR
ON/OFF/
PROGRAM
BUTTON

If within six (6) years from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This war-
ranty is extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or
any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost
of the product; (e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit
damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRAN-
TIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED
WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the
authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.homesettings.com
Please be sure to wrap the product securely to avoid shipping damage.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
After including your HA01 In-Wall Receptacle in your Home-
Settings network, you must associate it with a specific control
channel (or pair of ON/OFF buttons) so you can operate it by
remote control. For a non-HomeSettings network, follow con-
troller instructions provided by the manufacturer.
Decide which pair of ON/OFF buttons you want to use to con-
trol the In-Wall Receptacle. Each pair represents a channel.
Press and hold (at the same time) both ON and OFF buttons
on the HA07 Master Controller or the HA09 Handy Control-
ler. After about 3 seconds:
The Master Controller screen will display LEARN.
The Handy Controller lights will rapidly flash GREEN and
RED at the same time.
Release the ON and OFF buttons on the controller.
Press and hold the INCLUDE button on the Master Controller
1.
2.
-
-
3.
4.
3 – ASSOCIATE the In-Wall Receptacle with a control channel
If necessary, you can delete the HA01 In-Wall Receptacle from
your HomeSettings network—or any network that supports
Z-Wave devices—through a process called EXCLUSION.
Put the controller into EXCLUSION mode. On the HA07
Master Controller or the HA09 Handy Controller, press and
release the DELETE button. For other manufacturers’ control-
lers, follow the instructions provided by the manufacturer.
Press the ON/OFF/PROGRAM button on the HA01 In-Wall Re-
ceptacle. If the exclusion is successful:
The HA07 screen will display SUCCESSFUL.
The HA09 will show a solid GREEN light for 2 seconds.
If the screen displays NOT SUCCESSFUL or the light is RED,
the exclusion has failed. Try again. If the procedure continues
to fail, contact Intermatic Customer Service.
1.
2.
-
-
Optional: EXCLUDE the In-Wall Receptacle from your network
After hard-wiring the HA01 into place, the device is ready to
join your HomeSettings network—or any network that sup-
ports Z-Wave™ devices—through a process called INCLUSION.
NOTE: Before you begin, devices (such as lamps) should
be plugged in and turned ON before including the HA01 in
your network.
Put the controller into INCLUSION mode. On the HA07
Master Controller or the HA09 Handy Controller, press and
release the INCLUDE button. For other
manufacturers’ controllers, follow the
instructions provided by the manu-
facturer.
Press the ON/OFF/PROGRAM button on
the HA01 In-Wall Receptacle. If the
inclusion is successful:
The HA07 screen will display SUC-
CESSFUL.
The HA09 will show a solid GREEN light for 2 seconds.
If the screen displays NOT SUCCESSFUL or the light is RED,
the inclusion has failed. Try again. If the procedure contin-
ues to fail, contact Intermatic Customer Service.
1.
2.
-
-
2 – INCLUDE the In-Wall Receptacle in your network or the Handy Controller.
The Master Controller screen will display INCL.
The Handy Controller will show a solid GREEN light only.
While still holding the INCLUDE button, press the ON/OFF/PRO-
GRAM button on the In-Wall Receptacle.
NOTE: If the GREEN Indicator light on the HA01 is not ON,
press the ON/OFF/PROGRAM button again to turn on the
light before proceeding to Step 6.
Release the INCLUDE button. If the association is successful:
The Master Controller screen will display SUCCESSFUL.
The Handy Controller GREEN light will simply turn off.
Test the channel you have just programmed by pressing its
ON and OFF buttons. The light should power ON or OFF.
If the screen displays NOT SUCCESSFUL or the light is RED,
the association has failed. Try again. If the procedure contin-
ues to fail, contact Intermatic Customer Service.
-
-
5.
6.
-
-
7.
Ratings: 15 A, 125 VAC, 50/60 Hz
Operating Temperature Range: 32°F to 104°F / 0°C to 40°C
Radio Operating Frequency: 908.42 MHz
RF (wireless) Range: 50-100 ft. under normal operating conditions
Made in China
•
•
•
•
•
Technical Information
Limited Six-Year Warranty
Federal Communications Commission Statement / Industry Canada Statement
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna or device.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTICE — Changes or modifications not expressly approved by Intermatic Inc., could void the user’s authority to operate the equipment.
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.
•
•
•
•
158HA11639