INTERSCALE MP-X300 User manual

Thank you for purchasing this scale.
Please read all operating instructions
carefully before use. This electronic scale
is a precision instrument. With normal
care and proper treatment, it will provide
years of reliable service.
Never load the scale with more than
the maximal capacity. Overloading can
permanently damage it!
Avoiding any exposure to extreme heat
or cold, your scale works better when
operated at normal room temperature.
Always allow the scale to acclimate to
normal room temperature for at least 1
hour before use.
Give your scale sufcient warm up time.
Usually 30 seconds to give the internal
components a chance to stabilize before
calibration.
Keep your scale in a clean environ-
ment. Dust, dirt, moisture, vibration, air
currents and a close distance to other
electronic equipment can all cause an
adverse effect on the reliability and
accuracy of your scale. Handle with care.
Gently apply all items to be weighed
on to tray top. Although this scale is
designed to be quite durable, try to avoid
rough treatment as this may permanently
damage the internal sensor.
Avoid shaking, dropping or otherwise
shocking the scale. This is a precision
instrument and must be handled with
extreme care.
Only operate the scale on a stable vibra-
tion free surface.
I. OPERATION:
1. Place scale on a horizontal at surface,
press [ON/OFF] key to turn on the scale.
2. Wait until “0.0“ is displayed.
3. Put the objects on the weighing platform.
4. Press and hold the “MODE“ key for 3
seconds to switch between the weighing
units.
II. TARE WEIGHING:
1. Turn on scale.
2. Place the “tare item“ on the platform
3. Press [MODE] key shortly, the LCD
will display “0.0“.
4. Add the “net-weight-item“.
USER MANUAL
interscale

V. TROUBLESHOOTING:
The primary reasons for inaccuracy or
malfunction are low batteries, incorrect
calibration, overload or operating on
an unstable surface. Please keep this
in mind and maintain and operate your
scale properly. The scale is a precise
instrument and must be handled with the
utmost care and caution.
III. CALIBRATION:
1. Press [ON/ OFF] key to turn on the scale
2. Wait until “0.0“ is displayed, press
and hold [ON / OFF] key for 5
seconds and then you will see “CAL“
3. Put the calibration weight onto
the platform
4. If you see “F“ on the LCD, this
indicates that the calibration is
nished successfully.
5. If you see ”E” on the LCD, this
indicates that the calibration is failed.
6. The scale will turn off automatically
after the calibration is nished.
IV. SPECIFICATION:
MP-X300: 300 g x 0,1 g
4 Units: 0,1 g/ 0,05 oz/ 0,05 ozt/ 0,06 dwt
MP-X50: 50 g x 0,01 g
4 Units: 0,1 g/ 0,05 oz/ 0,05 ozt/ 0,06 dwt
Calibration: Auto calibration
Tare range: Tare full capacity
Auto off: 30 seconds off
Power: 1 x CR2032 Batteries
Dimensions: 75 x 42,5x 12 mm
Weight: 42,3 g
Display - Elimination of errors
Nothing, Battery-Symbol
[lo] or [88888]
Change the batteries
[OUT2]
Recalibrate the scale as shown in III.
[O-LD]
You are overloading the scale. Remove
the excessive load immediately.
[O-LD] or [LLLLL]
The delicate weighing loads cells have
been damaged by misusing the scale (i.e.
it was shocked, dropped or overloaded).
You can try recalibrating the scale. If the
load cell has not been damaged too much
it will work again after recalibration.
[UNST]
Use the scale in a more
stable position.
©www.interscale.net 2007