Intex CHALLENGER 3a User manual

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 1 098-*A*-R1-1210
INTEX®OWNER’S MANUAL
INFLATABLE BOAT
IMPORTANT
THIS BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
READ IT THOROUGHLY BEFORE USING THIS PRODUCT AND
KEEP IT FOR FUTURE REFERENCE.
ISO-6185 BOAT DESIGN CATEGORY D

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 2
TABLE OF CONTENTS
INTRODUCTION.............................................................................................................................3
MANUFACTURE’S CERTIFICATION..............................................................................................3
SAFETY & WARNIN .....................................................................................................................3
MANUFACTURER’S RECOMMENDATION....................................................................................4
DESCRIPTION.............................................................................................................................5-7
INFLATIN INSTRUCTIONS...........................................................................................................8
HOW TO USE BOSTON VALVE.....................................................................................................8
FISHIN ROD HOLDER USE........................................................................................................9
SEAT INSTALLATION .....................................................................................................................9
OAR ASSEMBLY........................................................................................................................9-10
RAB LINE INSTALLATION..........................................................................................................11
ACCESSORY LINE INSTALLATION..............................................................................................11
SAFETY AND OPERATION INSTRUCTIONS..........................................................................11-12
CARE AND MAINTENANCE.........................................................................................................12
DISASSEMBLY AND STORA E...................................................................................................13
TROUBLESHOOTIN ..................................................................................................................13
REPAIRS.......................................................................................................................................13
LIMITED WARRANTY....................................................................................................................14
CONTACT OFFICE LIST...............................................................................................................15

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 3
•This is not a life saving device. Use only under competent supervision. Never allow diving into
this product. Never leave in or near the water when not in use. Never tow from any vehicle.
•Read the complete Owner’s Manual before use and store this Manual in a safe place for future
reference.
•Follow all the Safety and Operating Instructions on this Manual.
•TYPE II, inflatable boats capable of taking an outboard motor. Motors are not to exceed the
maximum recommended power and weight.
•Read the instruction of outboard motor for correct installation and operation.
•Never navigate alone. Beware of offshore winds and currents.
•Do not exceed the maximum recommended capacities. Overloading violates regulations.
•Everyone on board must wear a Personal Floatation Device (PFD).
•Use caution when stepping or climbing aboard the boat. Step into the center of the boat for
maximum stability.
•Distribute the weight of passengers, gear, tackle box, and accessories so that the boat sits level
fore (front) to aft (back) and side-to-side.
•Do not use your boat if you suspect a puncture or leak.
•Adults should inflate the chambers in numbered sequence.
•Not for white water rafting or any other extreme sports activities.
•Follow these rules to avoid drowning, paralysis or other serious injuries.
WARNING
Introduction
This manual has been compiled to help you to operate your craft with safety and pleasure. It contains
details of the craft, the equipment supplied or fitted, its systems, and information on its operation and
maintenance. Please read it carefully, and familiarize yourself with the craft before using it.
If this is your first craft, or you are changing to a type of craft you are not familiar with, for your own
comfort and safety, please ensure that you obtain handling and operating experience before
assuming command of the craft. Your dealer or national sailing federation or yacht club will be pleased
to advise you of local sea school, or competent instructors.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER
WHEN YOU SELL THE CRAFT. RECORD THE "HULL IDENTIFICATION NUMBER" (HIN) WHICH IS
PRINTED ON THE BOAT'S HULL IN THE FOLLOWIN BOX:
HIN: ________________________
Manufacture’s Certification
For boats between and including 2.5 and 24 meters hull length, a CE (FOR EUROPE ONLY) mark
means that the boat complies with European Directives for Recreational Craft 94/25/EC and
2003/44/EC as published by the International Organization for Standardization, ISO 6185.
NMMA (FOR USA ONLY) certification means that the boat, sold in the United States, has been
judged by the National Marine Manufacture’s Association to be in compliance with the U.S. Coast
uard Regulations and American Boat and Yacht Council (ABYC) standards and recommended
practices.
Safety
Boat Design Category D -“SHELTERED WATERS”-: Designed for voyages on sheltered coastal
waters, small bays, small lakes, rivers and canals when conditions up to, and including, wind
force 4 and significant wave heights up to, and including, 0.3 m may be experienced, with
occasional waves of 0.5 m maximum height, for example from passing vessels.

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 4
ISO 6185 PART 1 TYPE
CATEGORY D
Do not overinflate or use high pressure air
compressor to inflate.
Adults should inflate the chambers with cold air in
numbered sequence.
Use the enclosed ruler to check while inflating.
Nicht zu stark aufblasen und keinen Kompressor
zum Aufblasen verwenden.
Erwachsene sollten die kammern in der
angegebenen Reihenfolge mit kalter luft aufblasen.
Verwenden Sie das belgefügte Meßgerät um die
korrekte Füllung zu überprüfen.
Ne pas surgonfler. Ne pas utiliser de compresseur
pour le gonflage.
Le gonflage doit être effectué par un adulte avec de
l'air froid en suivant les étapes suivantes.
Utiliser la règle jointe pour ajuster le gonglage de la
chambre à air principale.
ISO-6185 boat design category (certain models). CE mark (for Europe only) (certain models).
Europe hull identification number (HIN). USA hull identification number (HIN).
Manufacturer’s recommended maximum load capacity. Maximum person’s capacity.
Manufacturer’s name and country of origin. Model name and number.
Manufacturer’s recommended working pressure.
NMMA (for USA only) certification means that the boat, sold in the United States, has been judged by
the National Marine Manufacture’s Association to be in compliance with the U.S. Coast uard
Regulations and American Boat and Yacht Council (ABYC) standards and recommended practices.
Maximum motor power and motor weight.
9
8
7
6
5
4
3
2
1
Manufacturer’s Recommendation
The total number of persons, motor power and total weight shall not exceed the limits printed on
the boat. Please refer to the boat's hull label for the actual values of your boat. See Table A.
BOAT LABEL FORMAT
10
MAXIMUM CAPACITIES
MAXIMUM-KAPAZITÃT
CAPACITÉS MAXIMUM
MAXIMUM POWER
MAXIMUM MOTORKRAFT
PUISSANCE MAXIMUM
PERSONS
PERSONEN
PERSONNES
MANUFACTURER
HERSTELLER
FABRICANT
MODEL
MODELL
MODÈLE
RECOMMENDED WORKING PRESSURE FOR EACH CHAMBER
EMPFOHLENE ARBEITENDE DRUCK FÜR EDE LUFTKAMMER
RECOMMANDÉ FONCTIONNEL PRESSION POUR CHAQUE CHAMBRE À AIR
CN-XEE ________
XEE ________
BY INTEX®
LOAD CAPACITY
BASIC FLOTATION ___Kg ( ___ Lbs) MAX.
National Marine Manufacturers Association
____________________
= ___ bar ( ___ psi)
CHINA
3
5
6
7
8
9
2
1
10
MAXIMUM CAPACITIES
PERSONS OR ____kg (___Lbs)
____ ____ POUNDS, PERSONS, GEAR, ENGINE
DESIGN COMPLIANCE WITH NMMA REQUIREMENTS BELOW IS VERIFIED.
MFGR. RESPONSIBLE FOR PRODUCTION CONTROL
+ + = ___ Kg ( ___ Lbs)
+ +
___kW (___HP) / ___Kg (___Lbs)
= ___
11
4
11
CHALLEN ER 3a
CHALLEN ER 4a
SEAHAWK 2
SEAHAWK 3
SEAHAWK 4
EXCURSION 2
EXCURSION 3
EXCURSION 4
EXCURSION 5
SEAHAWK II
MARINER 4
68369
68371
68346
68349
68350
68318
68319
68324
68325
68377
68376
II
II
II
II
II
II
II
II
II
II
II
2.95
3.51
2.36
2.95
3.51
2.41
2.62
3.15
3.66
2.97
3.28
1.37
1.45
1.14
1.37
1.45
1.45
1.57
1.65
1.68
1.27
1.45
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
3
255
340
200
300
400
200
300
400
455
300
400
3
4
2
3
4
2
3
4
5
3
4
9
13
6
11
17
13
15
19
22
16
32
0.035 (0.5)
0.035 (0.5)
0.069 (1.00)
0.069 (1.00)
0.069 (1.00)
0.069 (1.00)
0.069 (1.00)
0.069 (1.00)
0.069 (1.00)
0.080 (1.14)
0.080 (1.14)
MODEL TYPE
Unladen Craft Weight
mmHP KgKg
bar (psi)
LhWh
TABLE A

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 5
Description
Challenger Series
36
Seahawk 2
Seahawk 4
1
19
8
728
7
24
45
5610 35
Seahawk 3
1810
7294 6
Seahawk Series
Seahawk
911 11
1110
" " - Recommended seating arrangement of the occupants.
" " - Recommended seating arrangement of the occupants.
36
Challenger 4a
110
28
45
35
Challenger 3a
18 102 46 11
11

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 6
Excursion Series
142 7691053
14267 91053 14267 91053
Excursion 4 Excursion 5
Excursion 2
142679 1053
Excursion 3
Seahawk II
1
11
3
86
57 10
2
12
1111
11
11
4
9
" " - Recommended seating arrangement of the occupants.
" " - Recommended seating arrangement of the occupants.

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 7
Mariner 4
1
68
3457
9
2
12
13
10
11
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
rab handle
All around grab line
Seat or seat cushion
Inflatable floor or removable slats floor
Oar lock
Oar holder
ear pouch or accessory bag
Inflation valve / Keel valve
Fishing rod holder
Motor mount
Boston valve
Rock guard
Inflatable keel
1
2
3
4
5
6
7
Descriptions
8
9
10
11
12
13
" " - Recommended seating arrangement of the occupants.

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 8
Inflating Instructions
Before starting, locate a clean area free of stones or other sharp objects. Unroll the boat so it is laid
out flat, and locate your pump.
Use a hand or foot operated air pump to inflate the boat. Do not use high-pressure air compressors.
Adults should inflate the chambers following the numerical sequence marked on the valves. It is very
important to follow the numerical sequence; failure to do so will result in an improperly inflated boat.
Fill each chamber until it is stiff to the touch but NOT hard. Use the enclosed ruler to check the main
chamber for proper inflation. DO NOT OVER INFLATE. Fill with cold air only.
IMPORTANT: Air temperature and weather condition do affect the internal air pressure of inflatable
products. In cold weather the product will lose some pressure due to the fact that the air will contract.
If this occurs, you may want to add a little air to the product. However, in hot weather, the air will
expand. You must let some air out to prevent the product from failing due to overpressure.
How to Use Boston Valve:
1. Double valve cap (valve lets air in, not out).
2. Quick deflation cap.
3. Unscrew Double valve cap.
4. Insert output end of air pump into valve and fill. Do not over inflate or use high pressure
compressor.
5. To deflate: unscrew quick-deflation cap. CAUTION: Double valve does not operate when this cap
is off. Do not unscrew this cap while boat or inflatable is in water.
Challenger series / Seahawk series / Excursion series:
1
2
3
45
12
3
4
5
Seahawk II / Mariner 4:

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 9
Fishing Rod Holder Use (Certain Models):
1. Slide the end cap over the end of the fishing rod.
2. Insert the fishing pole into the holder.
Seat Installation:
Certain Models:
1. Inflate each seat cushion slowly to about 75% of its capacity.
2. Attach the seat cushion hinge to the hinge on the boat. Repeat the
connection on the other side and for all seats. See Fig A.
3. Finish inflating the seat cushions slowly until it is firm to the touch
but NOT hard. DO NOT OVER INFLATE!
4. To disassemble the seats, deflate the seats first and reverse the
installation procedures.
NOTE: Some seat cushions after inflation are tuck in directly into
the fore, mid or aft locations of the boat cockpit. No hinges.
Seahawk II / Mariner 4:
1.
Inflate each seat cushion slowly to about 75% of its capacity.
2. Put the seat cushions into the fore, mid or aft locations of the boat cockpit.
3. Finish inflating the seat cushions slowly until it is firm to the touch but NOT hard. DO NOT OVER INFLATE!
4. Seat cushions after inflation are tuck in directly into the fore, mid or aft locations of the boat cockpit.
5. To disassemble the seats, deflate the seats first and reverse the installation procedures.
Fig A
Oar Assembly:
1. Insert “Shaft A” with the pin end first into the blade. Make sure the pin is securely fastened to the blade.
2. Insert the assembled “Shaft A” through the oar-lock with the blade towards outboard (water).
3. Place the retainer ring onto the other end of the assembled “Shaft A”, from inside of the boat.
4. Join “Shaft A” with “Shaft B” together by inserting them together into the coupler and tighten the coupler
covers securely.
5. When the oars are not in use secure the oars onto the oar holders located on each side of the boat.
Pin
Coupler Cover
Shaft B
Coupler
Shaft A
Blade
Retainer Ring
Fishing
Rod
Holder
End Cap
Fishing
Rod
Coupler Cover
Shaft
Coupler
Blade
Retainer Ring

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 10
FOR BOATS WITH ROTATION OAR-LOCK:
1.
3.
5.
4.
2.
10733
10734
Shaft B
Shaft A
Coupler Cover
Coupler
Retainer Ring
Pin
Blade
FRENCH OARS:

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 11
Safety and Operating Instructions
Before Departing from the Shore or Dock
Know all required information and inform your passengers:
•Take a boating safety course and get hands-on training from your boat dealer or local boating
authorities.
•Know all local regulations and hazards related to water activities and boat operation.
•Check weather forecast, local currents, tides and wind conditions.
•Advise someone on land of the time you plan to be back at your starting point.
•Explain basic boat operation to all passengers.
•Children and non-swimmers need special instructions in the use of life jacket or personal floatation
devices (PFD).
•Be sure that one of your passengers can operate the boat in case of emergency.
•Learn how to determine the distance you can cover, and remember that bad weather conditions
can alter this.
•Review all safety requirements regularly.
Check the working condition of the boat and equipments:
•Check inflation pressure.
•Inspect the valves caps.
•Check the load is evenly distributed, fore (front) to aft (back) and side-to-side.
Make sure that all required safety equipment is on board (check the laws and regulations of the
country or locality in which you are boating to see if additional equipment may be needed):
•One personal flotation device (PFD) per person.
•Air pump, oars, repair kit and tool kit.
•Any other mandatory equipment.
•The boat papers and your boating license (if applicable).
•Lights are required if operating after dark.
Figure eight knot
Accessory Line Installation (Certain
Models):
Your boat may have accessory lines to install. Tie a
figure eight knot into one end of the accessory line
and slide it through the rope holders. Tie a figure
eight knot in the remaining end of the rope.
The accessory bags may or may not be attached to
the accessory lines. Slide the rope through the
accessory bags while installing the accessory lines, if
desired.
Square knot
Grab Line Installation (Certain Models):
IMPORTANT: To properly install the inflatable boat’s grab line
and/or accessory lines, first inflate the boat.
If is necessary, begin the grab line installation at the rear of the
boat by threading it through the rope holders completely around
the outside of the boat. Tie the two loose ends in a square knot
at the rear end of the boat.

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 12
Rules to Observe During Navigation
•Be responsible, do not neglect the safety rules, this could jeopardize your life and the lives of
others.
•Always keep control of your boat.
•Respect local regulations and practices.
•Near the shore, navigate in the designated boating area.
•Remember that weather conditions can rapidly deteriorate. Always be sure that you can reach a
shelter rapidly.
•Everyone on board must always wear a personal flotation device (PFD).
•Do not drink alcohol or take drugs before or while operating your boat. Maintain passenger
sobriety.
•Do not exceed the authorized number of persons or weight.
•Make sure your passengers remain seated at all times. At planning speeds, in rough water or
during sharp turns, all passengers should position themselves in seats or on the floor.
•No bow riding. Bow riding is illegal in most areas and is extremely dangerous. In case of falling,
the man overboard is in the way of the propeller.
•Be especially careful when docking. Arms and legs may be injured if they are outside the boat.
•Keep clear of swimmers and divers. Always avoid areas where divers/swimmers are in the water.
•Keep a sharp lookout especially when operating near beaches and launch sites. The Alpha flag
indicates proximity of divers. You MUST maintain a safe distance as required by your local boating
laws, which may range from 50 meters (164 feet) to 91 meters (300 feet).
•Avoid sharp turns at high speeds. You could get ejected from the boat.
•Do not make changes in direction without advising passengers.
•Avoid all contact between the buoyancy tubes and sharp objects or aggressive liquids (such as
acid).
•Do not smoke on board. Most importantly while filling the fuel tank.
•Any fuel spilled must be cleaned and disposed of according to local laws and regulations.
Care and Maintenance
The boat is made of the highest quality materials and complies with ISO 6185 standards. Altering the
construction of the boat will endanger your own safety, safety of the occupants and void the limited
warranty!
There is very little that you have to do to keep your boat in good condition for many years. You may
store it inflated or deflated. If you leave it outside, raise it up off the ground and do not place any
heavy or sharp objects on it. If it is going to be in direct sunlight or exposed to leaves or rain, cover it
with a tarp. We do not recommend hanging the boat. If you store it in a closet, basement or garage,
we suggest you pick a cool, dry place, making sure the boat is clean and dry before you store it - or
mold can accumulate.
Use as few cleaning agents as possible, do not discharge waste agents into water, and clean your
boat preferably on land.
Clean your boat after a trip to prevent damage from sand, salt water or sun exposure.
Most dirt can be removed with a garden hose, a sponge and mild soap. Make sure the boat is
completely dry before storing. Store the product and accessories in a dry, temperature controlled,
between 32 degrees Fahrenheit (0 degrees Celsius) and 104 degrees Fahrenheit (40 degrees Celsius)
storage location.

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 13
Disassembly and Storage
First clean your boat thoroughly following the Care and Maintenance instructions. Open all air valves
and deflate boat completely. Remove all the accessories from the boat; seats, fishing rod holders,
oars, gear pouch and battery pouch.
Fold the left and right chambers of the boat towards the middle of the floor. It is not necessary to
remove the slats to fold the boat. Fold the bow end twice to the middle of the boat tightly while forcing
out any remaining air; repeat this procedure for the stern. With two opposing folded sides, fold one end
over the other like closing a book. Replace all inflation valve caps. Your boat is ready for storage. Fold
the boat loosely and avoid sharp bends, corners and creases which can damage the boat.
Troubleshooting
If your boat appears a bit soft, it might not be because of a leak. If the boat was inflated late in the day
with 32 °C (90 °F) air, that air might cool down to 25 °C (77 °F) overnight. The cooler air exerts less
pressure on the hull, so it could appear soft the next morning.
If there has been no temperature variation, you need to start looking for a leak:
•Take a good look at your boat from just a few feet away. Flip it over and closely check over the
outside. Any large leaks should be clearly visible.
•If you have an idea where your leak is, use a mix of dishwashing liquid and water in a spray
bottle, and spray over the suspicious areas. Any leak will produce bubbles that will pinpoint the
location of the leak.
•Check valves for leak, if necessary, spray soapy water around the valve and the valve base.
Repairs
Through constant use you may occasionally puncture your boat. Most leaks only take a few minutes to
repair. Your boat comes with a repair patch, and additional repair supplies can be ordered from Intex
Consumer Service or from our website.
First locate the leak; soapy water will bubble out from the source of the leak. Thoroughly clean the
area surrounding the leak to remove any dirt or grime.
Cut a piece of repair patch large enough to overlap the damaged area by approximately 1.5 cm (1/2”).
Round off the edges, and place the patch on the damaged area and PRESS DOWN FIRMLY. You may
want to use a weight on top to keep it in place.
Do not inflate in 30 minutes after patching.
If the patch does not hold, you can purchase a PVC or silicon based glue for repairing camping mats,
tents or shoes from your local market to patch your boat, please refer to the instruction of the glue for
patching.

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 14
Limited Warranty
Intex Inflatable Boat
Your Intex Inflatable Boat has been manufactured using the highest quality materials and
workmanship. All Intex Inflatable Boats have been inspected and found free of defects prior to leaving
the factory. This Limited Warranty applies to the Intex Inflatable Boat only.
The following provision is only valid within the European member states countries: The legal
regulation of Directive 1999/44/EC will not be effected by this Intex warranty.
The provisions of this Limited Warranty apply only to the original purchaser. This Limited Warranty is
valid for a period of 90-days from the date of purchase. Keep your purchase information with this
manual, as proof of purchase will be required and must accompany warranty claims or the Limited
Warranty is invalid.
If a manufacturing defect is found within this 90-day period, please contact the appropriate Intex
Service Center listed on the next page. If the item is returned as directed by the Intex Service Center,
the Service Center will inspect the item and determine the validity of the claim. If the item is covered
by the provisions of the warranty, the item will be repaired or replaced at no charge.
IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND IN NO EVENT
SHALL INTEX, THEIR AUTHORIZED A ENTS OR EMPLOYEES BE LIABLE TO THE BUYER OR
ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL DAMA ES OR LIABILITIES. Some states,
or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
This Limited Warranty does not apply if the Intex Inflatable Boat is subject to negligence, accident,
improper operation, trailering or towing, improper maintenance or storage, abnormal use or
application, or to damage by circumstances beyond Intex’s control, including but not limited to,
punctures, tears, abrasions, or ordinary wear and tear. This Limited Warranty applies only to those
parts and components manufactured by Intex. The Limited Warranty does not cover unauthorized
alterations to the boat.
Read the owner’s manual carefully and follow all instructions regarding proper operation and
maintenance of your Intex Inflatable Boat. Always inspect your equipment prior to use. Your Limited
Warranty may be void if instructions are not followed.
RECORD THE OWNER’S NAME, ADDRESS, PHONE NUMBER AND CRAFT HIN BELOW:
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________

98A
(98IO) "ISO" BOAT W / MOTOR MOUNTIN (TYPE II) EN LISH 7.5”X10.3” 10/07/2011
SAVE THESE INSTRUCTIONS
Page 15
©2011 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten.
Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas
utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd.
to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach,
CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der
Europäischen Union durch/Intex Trading B.V., P.O. Box nr. 1075 – 4700 BB Roosendaal – The Netherlands
AREAS LOCATION AREAS LOCATION
For service questions or to order replacement parts, please contact the appropriate office listed
below or visit www.intexdevelopment.com for answers to most frequently asked questions.
• ARGENTINA ARSE INDUSTRIAL Y COMERCIAL S.A
MANUEL GARCIA 124 (CP1284)
CIUDAD AUTÓNOMA DE BUENOS AIRES,
ARGENTINA.
TEL: [phone] (interno 139);
TEL: [phone]( interno 145)
E-mail: Martín Cosoleto: [email protected]
E-mail: Daniel Centurion: [email protected]
Website: www.jarse.com.ar
• PERU COMEXA S.A.
AVENIDA COMANDANTE ESPINAR 142,
MIRAFLORES, LIMA, PERÚ
TEL: [phone]
• SAUDI ARABIA SAUDI ARABIAN MARKETING &
AGENCIES CO. LTD.
PRINCE AMIR MA ED STREET,
AL-SAFA DISTRICT. EDDAH,
KINGDOM OF SAUDI ARABIA
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.samaco.com.sa
• AUSTRIA STEINBACH VERTRIEBSGMBH
AISTINGERSTRAßE 2
4311 SCHWERTBERG
TEL: 0820 - 200 100 200
(0,145€/min aus allen Ne zen)
FAX: + 43 (7262) 61439
E-mail: [email protected]
Website: www.intexcorp.at
• CZECH REPUBLIC / INTEX TRADING S.R.O.
EASTERN EUROPE BENESOVSKA 23,
101 00 PRAHA 10,
CZECH REPUBLIC
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
•BELGIUM N.V. SIMBA-DICKIE BELGIUM S.A.
MOESKROENSESTEENWEG 383C,
8511 AALBEKE, BELGIUM
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]
E-mail: [e-mail]
Website: www.nicotoy.be/downloads.htm
•DENMARK K.E. MATHIASEN A/S
SINTRUPVE 12, DK-8220
BRABRAND, DENMARK
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexnordic.com
•SWEDEN LEKSAM AB
BRANDSVIGSGATAN 6,
S-262 73 ÄNGELHOLM,
SWEDEN
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexnordic.com
• NORWAY NORSTAR AS
PINDSLEVEIEN 1,
N-3221 SANDEF ORD,
NORWAY
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]
Website: www.intexnordic.com
• FINLAND NORSTAR OY
SUOMALAISTENTIE 7,
FIN-02270 ESPOO,
FINLAND
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]
Website: www.intexnordic.com
• RUSSIA LLC BAUER
KIEVSKAYA STR., 20,
121165 MOSCOW, RUSSIA
TEL: [phone]/9802
FAX: [phone]
E-mail: [email protected]
Website: www.intex.su
• POLAND KATHAY HASTER
UL. LUTYCKA 3, 60-415 POZNAN
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]
Website: www.intexdevelopment.pl
• HUNGARY RECONTRA LTD./RICKI LTD.
H-1113 BUDAPEST, DARÓCZI ÚT 1-3,
HUNGARY
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
• BRASIL KONESUL MARKETING & SALES LTDA
RUA ANTONIO DAS CHAGAS,
1.528 - CEP. 04714-002,
CHÁCARA SANTO ANTONIO - SÃO
PAULO - SP - BRASIL
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
• ISRAEL ALFIT TOYS LTD
MOSHAV NEHALIM,
MESHEK 32, 49950, ISRAEL
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
• ASIA INTEX DEVELOPMENT CO. LTD.
9TH FLOOR,
DAH SING FINANCIAL CENTRE,
108 GLOUCESTER ROAD,
WANCHAI, HONG KONG
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexdevelopment.com
• EUROPE INTEX TRADING B.V.
POSTBUS 1075, 4700 BB ROOSENDAAL,
THE NETHERLANDS
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexcorp.nl
• FRANCE UNITEX / INTEX SERVICE FRANCE S.A.S
Z.A. DE MILLEURE
BOIS DU BAN - N°4
71480 LE MIROIR
TEL: [phone] (0,15€/min)
FAX: [phone]
Website: www.intex.fr
•GERMANY STEINBACH VERTRIEBSGMBH
C/O WEBOPAC LOGISTICS GMBH
INTER-LOGISTIK-PARK 1-3
87600 KAUFBEUREN
TEL: [phone]
(0,14€/min aus dem Festnetz, Mobilfunk max. 0,42€/min)
FAX: + 43 (7262) 61439
E-mail: [email protected]
Website: www.intexcorp.de
• ITALY A & A MARKETING SERVICE
VIA RAFFAELLO SANZIO 19
20852 VILLASANTA (MB)
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexitalia.com
• UK OHN ADAMS LEISURE LTD
MARKETING HOUSE,
BLACKSTONE ROAD,
HUNTINGDON, CAMBS.
PE29 6EF. UK
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexspares.com
• SWITZERLAND GWM AGENCY
GARTEN-U. WOHNMÖBEL,
RÄFFELSTRASSE 25,
POSTFACH,
CH-8045 ZURICH/SWITZERLAND
TEL: [phone] or [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.gwm.ch, www.gwmsale.ch
•SPAIN / PORTUGAL Nostrum Iberian Market S.A.
Av. de la Albufera, 321
28031 Madrid, Spain
TEL: [phone]
FAX for Spain: [phone]
Email for Spain: [email protected]
FAX for Portugal: [phone]
Email for Portugal: [email protected]
Website: www.intexiberian.com
•AUSTRALIA HUNTER PRODUCTS PTY LTD
LEVEL 1, 225 BAY STREET,
BRIGHTON, VICTORIA,
AUSTRALIA
TEL: [phone] or 1800-224-094
FAX: [phone]
E-mail: [email protected]
Website: www.hunterproducts.com.au
• NEW ZEALAND HAKA NEW ZEALAND LIMITED
UNIT 4, 11 ORBIT DIVE, ALBANY,
AUCKLAND 0757, NEW ZEALAND
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.hakanz.co.nz
• MIDDLE EAST FIRST GROUP INTERNATIONAL
REGION AL MOOSA GROUP BUILDING, 1ST
FLOOR, OFFICE 102 & 103, UMM HURAIR
ROAD, KARAMA, DUBAI, UAE
TEL: [phone]INTEX(46839) / [phone]
FAX: [phone]
E-mail: [email protected].
Website: www.firstgroupinternational.com
• SOUTH AFRICA WOOD & HYDE
15-17 PACKER AVENUE, INDUSTRIA 2,
CAPE TOWN, SOUTH AFRICA 7460
TEL: [phone] (Toll Free) or 27-21-505-5500
FAX: [phone]
E-mail: [email protected]
• CHILE / URUGUAY COMEXA S.A.
EL UNCAL 100, PARQUE INDUSTRIAL PORTEZUELO,
QUILICURA, SANTIAGO, CHILE.
TEL: [phone]
E-mail: [email protected]