Intex PureSpa SSP-H-10-1 User manual

263
PO
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
OWNER’S MANUAL
PureSpa™
SSP-H-10-1
110-120V~, 60Hz, 12A
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
263-*PO-R0-1507
Do not forget to try these other fine Intex products: pools, pool
accessories, in-home toys, airbeds and boats available at fine
retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves
the right to change specifications and appearance, which may
result in updates to the instruction manual, without notice.
For illustrative purposes only.
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance, visit
www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 2
Warning.......................................................................................... 3-4
Parts............................................................................................... 5-6
Set-up............................................................................................. 7-10
Operation....................................................................................... 11
LED Code Chart............................................................................. 12
Maintenance and Chemicals........................................................ 13-17
Storage........................................................................................... 18
Troubleshooting............................................................................ 19
Warranty......................................................................................... 20
TABLE OF CONTENTS
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 3
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following.
READ AND FOLLOW ALL INSTRUCTIONS
• Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by
children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at all
times.
• Risk of drowning. Inspect the spa cover regularly for leaks, premature wear and tear, damage, or signs of
deterioration. Never use a worn or damaged cover: it will not provide the level of protection required to
prevent unsupervised access to the spa by a child.
• Risk of injury. Replace damaged cord immediately. Do not bury cord. Connect to a grounded, grounding
type receptacle only.
• Risk of Injury. The suction fittings in this spa are sized to match the specific water flow created by the
pump. Should the need arise to replace the suction fittings or the pump, be sure that the flow rates are
compatible.
• To reduce the risk of injury, do not remove the suction fittings. Never operate a spa or hot tub if the suction
fittings are loose, broken, damaged, cracked or missing. Replace immediately. Never replace a suction
fitting with one rated less than the flow rate marked on the original suction fitting.
• To reduce the risk of drowning from hair and body entrapment, install a suction fitting(s) with a marked flow
rate that equals or exceeds the flow rate marked on the equipment assembly.
• Make sure the power outlet current and voltage is suitable for the electrical equipment.
• Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces. As an alternative, a spa may
be installed within 5 feet (1.5 m) of metal surfaces if each metal surface is permanently connected by a
minimum 8 AWG (8.4 mm2) solid copper conductor to the wire connector on the terminal box that is
provided for this purpose.
• Risk of Electric Shock. Do not permit any electric appliance, such as a light, telephone, radio, or television,
within 5 feet (1.5 m) of a spa or hot tub.
• Risk of Electric Shock. Do not use the spa when it is raining, thundering or lightning.
• A wire connector is provided on this unit to connect a minimum 8 AWG (8.4 mm2) solid copper conductor
between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or
conduit within 5 feet (1.5 m) of the unit.
• To reduce the risk of drowning and injury, do not permit children to use this product unless they are closely
supervised at all times.
• To reduce the risk of child drowning, attach and lock spa cover after each use.
• To reduce the risk of drowning and injury:
a) Never use the spa alone or allow others to use the spa alone.
b) Before entering a spa or hot tub, the user should measure the water temperature with an accurate
thermometer since the tolerance of water temperature-regulating devices varies.
c) The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and
104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for
young children and when spa use exceeds 10 minutes.
d) Pregnant and possible pregnant women should consult a physician before using a spa or hot tub.
e) Since excessive water temperatures have a high potential for causing fetal damage during the early months
of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C) .
Do not stay in spa for longer than 10 minutes.
f) The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the
possibility of drowning.
g) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system
problems, or diabetes should consult a physician before using a spa.
h) Persons using medication should consult a physician before using a spa since some medication may
induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.
i) Check with a doctor before use if pregnant, diabetic, in poor health, or under medical care.
DANGER
WARNING

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 4
j) Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyperthermia and unconsciousness.
The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. The causes,
symptoms, and effects of hyperthermia may be described as follows:
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the
normal body temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the
internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia
include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness of
impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and
unconsciousness resulting in the danger of drowning.
• People with infectious diseases should not use a spa or hot tub.
• To avoid injury exercise care when entering or existing the spa or hot tub.
• Always add chemicals to water, never add water to chemicals. Adding water to chemicals may cause
strong fumes or violent reactions and hazardous chemical spray.
• Never jump or dive into a spa or any shallow body of water.
• Assembly and disassembly by adults only.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any
adjustment to the product.
• The plug must be accessible after product is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge
trimmers and other equipment.
• If the supply cord is damaged, it must be replaced by a qualified electrician in order to avoid a hazard. Use
only identical replacement parts when servicing.
• To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to
connect unit to electrical supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
• Do not leave the spa empty for extended period of time. Do not expose the spa under direct sunshine.
• Adequate drainage system must be provided around the spa to deal with overflow water.
• Do not allow the water in the spa to freeze. Do not turn on the spa when the water is frozen.
• Do not use the spa if damaged in delivery and/or malfunctioning in any fashion. Contact the Intex service
center for further direction.
• Never pour water with a temperature higher than 104°F (40°C) into the spa directly.
• Keep all pets away from spa to avoid any damage.
• Do not add bath oil or bath salt to the spa water.
WARNING
CAUTION
• Maintain water chemistry in accordance with manufacturer’s instructions.
• This product is provided with a GFCI/RCD located at the end of the power cord. The GFCI/RCD must be
tested before each use. Do not use the spa if the GFCI/RCD does not function properly. Disconnect the
power cord until the fault has been identified and corrected. Contact a qualified electrician to correct the
fault. Do not bypass the GFCI/RCD. There are no serviceable parts inside the GFCI/RCD. Opening the
GFCI/RCD will void the warranty.
1. Plug the power cord into a grounded electrical socket.
2. Press the RESET button on the GFCI/RCD.
3. Turn on the spa electrical equipment.
4. Press the TEST button on the GFCI/RCD. The GFCI/RCD indicator
should turn off and the electrical equipment should shut off. If the
GFCI/RCD indicator does not turn off, and the electrical equipment
does not shut off, the GFCI/RCD is faulty. Do not use the spa.
Contact a qualified electrician to correct the fault.
5. Press the RESET button on the GFCI/RCD. The indicator on
the GFCI/RCD should turn on. If the GFCI/RCD indicator does
not turn on, the GFCI/RCD is faulty. Do not use the spa.
Contact a qualified electrician immediately to correct the fault.
WARNING
TEST
RESET
RESET
TEST
TEST
RESET
RESET
TEST
TEST

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 5
PARTS
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
810 11
18
17
19
9
21
23
22
2
7
3
4
5
15
16
20
25
12
13
14 24
26
27
6
29
30
28
1
A
C
B

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
When ordering parts, be sure to quote the model number and part numbers.
PARTS (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
Page 6
REF. NO. DESCRIPTION QTY. PART NO.
1 CONTROL BASE 1 11931
2 CONTROL BASE BACK COVER 1 11719
3 CONTROL PANEL (INCLUDED #4 ) 1 11930
4 CONTROL PANEL BOLT 3 11024
5 CONTROL BASE INFLATION CAP 1 11831
6 CONTROL PANEL BOLT WRENCH 1 11053
7 SPA/COVER INFLATION HOSE 1 11830
8 SPA CONTROL INLET/OUTLET O-RING 2 11699
9 SPA CONTROL AIR INLET O-RING 1 11687
10 SPA DRAIN PLUG 1 11696
11 SPA DRAIN VALVE ADAPTOR 1 11713
12 FILTER CARTRIDGE HOUSING 2 11798
13 FILTER CARTRIDGE 2 11692
14 FILTER CARTRIDGE HOUSING LID 2 11797
15 INLET/OUTLET PLUG 3 11739
16 SPA TUB 1 11879
17 SPA COVER 1 11878
18
SPA COVER INFLATABLE BLADDER (PRE-INSTALLED IN SPA COVER) 111884
19 GROUND CLOTH 1 11933
20 CHEMICAL DISPENSER 1 11614
21 TEST STRIPS 1 11855
22 WRENCH 1 11742
23 PRESSURE GAUGE 1 11741
24 SUCTION FITTING 3 11695
25 INFLATION HOSE ADAPTOR 1 11829
26 MALE BUCKLE 8 11698
27 FEMALE BUCKLE 811799
28 DEFLATION OUTLET CAP 1 11934
29 DEFLATION HOSE ADAPTOR 1 11935
30 SPA FILTER MOTOR 1 11885
SPA SUCTION FITTING
Self-contained spa fittings. – For multiple outlet use only. – Wall mounting only.
Replace suction fittings within 3 installed year. – Tool required: screwdriver.
Spa suction fitting maximum flow rate: 8.5 gpm (510 gph)
•
Check suction strainer fitting and fasteners for damage or tampering before each use of the spa.
•
For service and winterization instructions refer to “Maintenance” and “Storage” sections.
•
Read and follow all instructions, save these instructions for future reference.

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Site preparation and requirements
• The spa can be installed indoor or outdoor. For household use only.
• The spa must be setup on a level, flat and smooth surface that is capable of supporting the maximum load
of the filled spa with four adult occupants; weight 2500 lbs (1136Kg).
• Make sure the area is free of sharp objects under or around the spa.
• Provide adequate drainage system around the spa to deal with overflow water and splashes.
• Provide a properly located power outlet to connect the spa and allow easy access for periodic testing of the
cord mounted GFCI/RCD.
• Make sure there is enough clearance around the spa for full access to the spa equipment for maintenance
and/or service.
• The area shall facilitate draining purposes during long term spa storage.
Additional requirements for indoor installation
• Make sure the floor can support the full weight of the filled spa with the maximum number of occupants.
Check with a qualified contractor or a structural engineer to verify this requirement.
• Make sure the floor is water resistant and non-slip surface. Do not install the spa on carpet or other
materials that will be damaged by moisture, condensation.
• Do not install the spa indoors on a second floor above finished living space due to the possibility of water
and humidity damage.
• Humidity is a natural side effect of indoor spa installation. The room shall be properly ventilated to allow
moisture to escape. Install a ventilating system to prevent excess condensation, moisture in the room.
Additional requirements for outdoor installation
• Spa owners may need to comply with local or states laws relating to childproof fencing, safety barriers,
lighting, and other safety requirements. Contact your local building code enforcement office for further
details.
• Make sure the surface is level, flat, smooth and strong enough to support the full weight of the filled spa.
• Do not setup the spa on grass or dirt, as this increases the amount of debris entering the spa, and damage
the spa floor.
• Do not expose the spa to direct sunlight for extended period of time.
• It is possible to install and leave the spa outside at a temperature not lower than 39°F (4°C) provided the
water temperature inside the spa is higher than 39°F (4°C) and the water inside the circulation system,
pump, pipe are not frozen. Put a “temp barrier mat” between the spa floor and the ground to prevent heat
loss from the bottom of the spa and to provide better heat retention.
Page 7
PRODUCT SPECIFICATIONS
SET UP
Maximum seating capacity: 4 adults
Water capacity: 210 gal (795 L)
Inner/outer diameter: 59/79 in (149/200 cm)
Height: 28 in (71 cm)
Bubble air blower: 1.1HP / 110-120 V / 60 Hz
Filter pump flow rate: 460 gal/hr (1,741 L/hr)
Heater power: 1,300 Watts / 110-120V / 60Hz
Temperature range: 68ºF – 104ºF (20ºC – 40ºC)
Temperature rise: 2-3ºF/hr (1-1.5ºC/hr)
Number of Bubble Jets: 120
Spa tub recommended working air pressure: 0.083 bar (1.2 psi)
Cord-connected spa with pump, heater, blower, built-in hard water treatment and control panel.
This product requires a minimum of 13 Amps. If the circuit breaker trips, please check that no other
appliances or other large loads are on the same circuit as the spa.

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
SET UP (continued)
Setup the spa with at least 2 persons.
1. Move the entire package to the selected site. Do not drag the spa tub across the ground as this can
cause damage and leakage.
Open the carton carefully as this carton can be used to store the spa during long term storage or when
not in use.
2. Lay out all the parts on the ground and make sure all the parts are accounted for. For missing or
damaged parts contact the appropriate Intex Service Center listed in the separate “Authorized service
Centers” sheet.
Safety Sign Card Posting
The Safety Sign card included with the manual shall be posted in an area visible to the users of the spa to
alert them of the safety rules and warnings. For replacement of the safety sign card, visit our website at
www.intexcorp.com for additional print copies. Laminate the printed safety sign copy for protection from the
elements.
Spa Control Unit Assembly
1. Connect the control panel (3) cable plug into the receptacle on top of the spa control base and screw in
the plug cover firmly by hand (see drawing 1).
2. Screw the control panel bolts (4) with the provided bolt wrench (6) to secure the control panel
(see drawing 2).
3. Plug the spa control unit into a grounded electrical outlet.
Page 8
Inflation
Inflate the Spa Tub Wall
1. Take out the ground cloth (19) and spread it over the cleared area. Then spread out the spa liner over
the ground cloth and point the drain valve towards a suitable draining area. Note: Spread the ground
cloth with the bubbles facing down over the cleared area where you intend to setup your spa.
2. Press the button located on top of the control base and remove the back cover (see drawing 3).
3. Unscrew the control base inflation cap (5) to reveal the air blower inflation outlet, insert one end of the
inflation hose (7) into the outlet and turn to the right to lock it (see drawing 4).
4. Unscrew the air valve cap to reveal the stem in the up position for inflation. Insert the other end of the
inflation hose (7) into the valve and turn to the right to lock it in position (see drawing 5).
4
6
2
3
Press
4 5
5
77
1 2
1
3
12

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 9
SET UP (continued)
5. Press the button to turn on the control unit panel buttons first. Press the button to inflate the
spa tub wall until it is firm to the touch but not hard (see drawing 6).
IMPORTANT: Do not over inflate or use high pressure air compressor to inflate.
6. Press the button again to turn it off.
7. Disconnect the inflation hose (7) from the air valve and attach the pressure gauge (23) to the air valve.
The pressure gauge indicator should be in the green area for a properly inflated spa tub (see
drawing 7). Repeat previous steps to add more air if necessary.
8. Replace the air valve cap back.
NOTE: The cap is designed to be screwed on and off. Never exert force as this could cause the
complete internal inflation system of the valve to come loose. See “Spa Tub Air Valve Fastening” for
valve maintenance.
Inflate the Spa Cover Air Bladder
1. Open the inflation valve and insert the inflation
hose
(7) into the valve; press to inflate
until it is firm to the touch but not hard (see
drawing 8).
2. Disconnect the inflation hose (7) from the air
blower inflation outlet and the valve.
3. Replace the control base inflation cap (5) back;
close and recess the inflation valve.
NOTE: If there is a need to add some air to the spa tub wall or spa cover air bladder after they have been
setup, refer to above “Inflate the Spa Tub Wall” and “Inflate the Spa Cover Air Bladder” sections. The cover
air bladder is preinstalled inside the spa cover. If it needs to be reinstalled, place the uninflated air bladder
inside the spa cover lip before inflating the bladder.
Deflation
For Spa Tub Wall:
1. Unscrew the cap to reveal the stem, push the stem
in and turn 90 degree right to secure it in the down
position
(see drawing 9).
2. Once the deflation is completed, push the stem in
and turn 90 degree left to return it to the inflation
position.
3. Replace the cap back.
For Cover Air Bladder:
1. Pull valve cap out and squeeze the valve at its base
until deflated.
2. Close and recess the valve back.
9
8
7
6 7
23
1
2

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 10
SET UP (continued)
Spa Control Unit Installation
1. Connect the spa control unit to the spa tub (see drawing 10). Hand-tighten the connectors securely.
Do not use tools to tighten.
2. Reinstall the back cover (2) to the spa control base (see drawing 11).
CAUTION: Back cover must be installed before using the SPA. Do not sit, lean, cover or place
any objects over the spa control unit.
3. Attach the two filter cartridge housing assemblies to the two outlet
grids on the inside of the spa (lower position, marked “C”). Inflate
the spa tub first before installing filter pump fittings.
ATTENTION! In order to comply with the requirements of the
Virginia Grahame Baker Act, suction outlets cannot be covered
while the spa is in use. The Act was intended to address high
suction / volume circulation systems but does not exclude low
volume systems as used on this spa. Accordingly, remove the filter
cartridge assemblies and any other spa cleaning attachment from
the spa outlets before spa usage (see drawing 12).
Re-attach them after usage for water filtration and cleaning.
4. Before filling with water ensure the bottom drain valve caps are
securely closed on the inside and outside.
5. Fill the spa tub with freshwater to a level between MIN and MAX
marked on the inside of the spa wall. Do not over fill the spa. Never move the spa tub with water inside
and/or with the control base attached to the spa as the spa or control base may be damaged.
. WARNING: Never pour water with a temperature higher than 104°F (40°C) into the spa directly. It is
recommended to fill the spa tub with lukewarm water for quick heating and energy saving.
6. Place the spa cover and spa air bladder (pre-installed in spa cover) over the spa tub, and make sure the
spa cover buckles are locked using the key provided after pulling the buckled straps tight.
IMPORTANT: Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never
use a damaged spa cover.
7. Ensure the spa is plugged into a grounded electrical socket and press the button to turn on the
control unit panel buttons first. Press the button on the control panel to activate the heater, see “Spa
Control Unit Panel” operation section. The heating system is capable of increasing the water
temperature by approximately 2-3ºF (1-1.5ºC) per hour.
12
C
11
2
AB
C
AB
C
10

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 11
OPERATION
SPA CONTROL UNIT PANEL
On/Off Button:
Once the unit is plugged in, use this button to active the control unit panel
buttons. The light next to the button is green when activated. Press this button to turn off all
currently activated functions.
NOTE: The On/Off button may appear as a black button in the center of the control panel.
Heat Button: Use this button to activate the heating system. The pump will heat the spa water
until the water temperature reaches the set temperature. When the spa water temperature drops
2°F below the set temperature the heating system will restart. When the flame icon on the
display is red, the heating system is activated. When the flame icon turns green, the water is at
the set temperature. The heating system is at rest and the filtration system will continue working
nonstop.
NOTE: To stop the filtration system while the heater is at rest mode, press the flame button first
and then the filter button. Pressing the flame button only while the heater is at rest mode will
turn off the heating system only and the filtration system will operate for another 24 hours before
it turns off automatically.
Celsius/Fahrenheit Toggle button:
The temperature can be displayed in either Fahrenheit or Celsius. The system’s default is
Fahrenheit.
CAUTION: NEVER use the spa if indicated water temperature is more than 104ºF (40°C).
Temperature Adjustment Buttons: Pressing the Temperature Increase or Decrease
buttons will cause the LED to flash. When flashing you can adjust to the desired temperature
setting. If you hold these buttons down the values will rapidly increase or decrease. The new
and desired temperature setting will remain on the LED display for 5 seconds to confirm the new
value.
NOTE: The default temperature is 68°F (20°C).
NOTE: Temperature adjustment ranges from 68°F (20°C) to 104°F (40°C).
Water Filter Button:
This button turns the filter pump on and off. If the heating system is activated the filtration
system will automatically start.
The water filter icon on the display is green when activated.
Bubble Button: Use this button to activate the massage system, which has a 30-minute
auto-shutoff feature. The bubble icon on the displays is green when activated.
WARNING: Do not run Bubble system when the cover is attached, air can accumulate
inside the spa and cause irreparable damage and bodily harm.
LED Display: Once plugged in the LED displays the current water temperature automatically.
NOTE: the built-in hard water treatment function works automatically in conjunction with the filtration system.
IMPORTANT: The following conditions will lead to slow water heating:
• The ambient temperature is lower than 50ºF (10ºC).
• Outdoor wind speed is above 8-12 mph (3.5-5. 4m/s).
• The air bubble function is activated when heating the spa water.
• The spa is not properly covered with the spa cover when the water is heating.
F
104o
A: Heat Button
B: Celsius/Fahrenheit Toggle Button
C: Temperature Increase Button
D: Temperature Decrease Button
E: Water Filter Button
F: Bubble Button
G: LED Display
H: On/Off Button
104 F
o
F
E
DC
B
A
G
H

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 12
LED CODE CHART
E90 No water flow
• Turn off and unplug the control unit.
• Ensure the outlet cover grid is clean and free
from obstructions.
• Clean or replace the cartridge, see
Maintenance and Storage section.
• Ensure the in/outlet connections on the spa tub
and filter pump are not blocked.
• Keep the spa water properly sanitized to
ensure a clean and unclogged filter cartridge.
• If problem persists, contact Intex Service
Center.
E94 Water temperature too low
•If the ambient temperature is below 39°F (4°C),
we recommend not to use the spa.
•Turn off and unplug the control unit, add some
warm water to raise the spa water temperature
above 41°F (5°C), then press the button to
heat up the water to the desired temperature.
•Press the temperature increase button to set
the desired water temperature.
•If problem persists, contact Intex Service
center.
E95 Water temperature too high
•Turn off and unplug the control unit. When the
water has cooled down, plug the GFCI/RCD
and restart all over again.
•Turn the heater off, then press the filter and
bubble buttons to lower the water temperature.
•If problem persists, contact Intex Service
Center.
E96 System Error
•Turn off and unplug the control unit, use the
cap to stop the water from flowing out of the
tub, disassemble and drain out the control unit.
Reassemble the control unit back to the tub.
Plug the GFCI/RCD and restart all over again.
•If problem persists, contact Intex Service
Center.
E99 Water temperature sensor broken •Contact Intex Service Center.
END
After 72 hours of operation,
the pump will hibernate and
the rapid heating and water
filtration functions are disabled.
•Press the button to re-active the
filter pump.
LED Reading CAUSE SOLUTION

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 13
MAINTENANCE AND CHEMICALS
Water Sanitation
The spa owner must regularly check and keep the spa water sanitized with scheduled maintenance (daily, if
necessary). Adding sanitizer and other chemical will control bacteria and viruses present in the spa water.
The maintenance of a proper water balance through appropriate use of sanitizers is the single most important
factor in maximizing the life and appearance of the spa tub as well as ensuring clean, healthy and safe water.
Proper technique is important for water testing and treating the spa water. See your pool/spa professional for
chemical, sanitizer, test kits and testing procedures questions.
CATUTION: ALWAYS FOLLOW THE CHEMICAL MANUFACTURER’S DIRECTIONS, AND THE HEALTH AND HAZARD
WARNINGS.
Do not add chemicals if the spa is occupied. This can cause skin or eye irritation. Concentrated chlorine
solutions can damage the spa tub. In no event is Intex Recreation Corp., Intex Development Co. Ltd., their
related companies, authorized agents and service centers, retailers or employees liable to the buyer or any other
party for costs associated with the loss of spa water, chemicals or water damage.
Maintenance of Spa Water and Cartridge
Protect all the spa occupants from possible water-related illnesses by keeping the spa water clean and sanitized.
Always practice good hygiene. To ensure proper spa water quality follow these procedures:
1. Inspect and clean the filter cartridge once a week, and change the filter
cartridge as needed.
a. Unscrew the cartridge housing assembly from the spa tub wall and
remove the cartridge
(see drawing 13).
b. Use a garden hose to rinse off the cartridge. If the cartridge remains
soiled and discolored it should be replaced. Keep spare cartridges
on hand.
c. Reinstall the clean cartridge back into the cartridge housing and
replace the cartridge housing assembly back onto the spa tub wall.
2. Change the spa water every 2~3 months, or it becomes cloudy and proper
water chemistry does not clear it up. See “Spa Tub Drainage” and “Spa
Tub Cleaning” sections for details.
3. Use spa chemicals to maintain proper water chemistry. Spa damage
resulting from misuse of chemicals and mismanagement of spa water
is not covered by the warranty.
4. All occupants must shower before entering the spa.
Water Chemistry Balance
Maintain the spa water pH level between 7.2 and 7.8, total alkalinity level between 80 and 120ppm and free
chlorine level between 2 to 4ppm. Use the included test strips to test the spa water chemistry before each use of
the spa and continue to test the water no less than once a week.
The Test Strips can test the “Free Chlorine”, “pH”, “Total Alkalinity” and “Calcium Hardness” levels at the same
time:
1. Dip the entire strip into the water and remove immediately.
2. Hold the strip level for 15 seconds. Do not shake excess water from the strip.
3. Compare the strip pad to the color chart on the packaging label. If necessary, adjust the chemical level
in the pool water.
NOTE: Check the expiry date of the test kit as the test results may be inaccurate if the kit is used after that date.
Low pH will damage the spa tub and pump. Damage resulting from chemical imbalance is not covered by the
warranty.
Use the included chemical floater dispenser to administer chlorine [chemical tablet size: less than 1” (2.5cm)
diameter] into the spa water. Add 1 tablet into the dispenser. Always follow the chemical manufacturer’s
directions. Remove the chemical floater dispenser when the spa is in use.
Never let chlorine come in contact with the spa tub if it is not completely dissolved.
IMPORTANT: Press the button on the spa control panel to turn on the bubble air blower and help dissolve
the chemicals into the water.
Never mix chemicals together. Add the chemicals to the spa water separately. Thoroughly dissolve each
chemical before adding another one to the water.
WARNING
Always unplug this product from the electrical outlet before removing, cleaning, servicing or
making any adjustment to the product.
13
14
12
13

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 14
Preferred Water Chemistry Reading
Minimum Ideal Maximum
Free Chlorine 2 ppm 2 - 4 ppm 5 ppm
pH 7.2 7.2 - 7.6 7.8
Total Alkalinity (TA) 60 ppm 80 ppm 120 ppm
Calcium Hardness (CaCO3)100 ppm 150–250 ppm 350 ppm
Saturation Index (SI) –0.3 0 +0.3
Water Temperature 20ºC / 68 ºF 20–40ºC / 68–104ºF 40ºC / 104ºF
Free chlorine: is the chlorine residual present in the spa water.
Result if too low – Inadequate level of disinfection.
Result if too high – cause odor problem, skin & eye irritation, corroded metals and other materials.
pH: a value that indicates how acidic or basic the spa water is.
Result if too low – Corroded metals, eye & skin irritation, and destruction of total alkalinity.
Result if too high – Scale formation, cloudy water, shorter filter/heater runs, eye & skin irritation, poor chlorine
efficiency.
Total Alkalinity (TA): indicates the degree of the water’s resistance to pH change. It determines the speed
and ease of pH change, so always adjust total alkalinity before adjusting the pH level.
Result if too low – Corroded metals, eye & skin irritation. Low alkalinity will cause the pH to be unstable.
Result if too high – Scale formation, cloudy water, shorter filter/heater runs, eye & skin irritation, high chlorine
demand.
Calcium Hardness (CaCO3): refers to the amount of calcium and magnesium dissolved in the water.
Result if too low – Difficulty balancing water, corrosion of metal components, eye & skin irritation and water
foaming.
Result if too high – Scale formation, cloudy water, eye & skin irritation, difficulty balancing water and filter/
heater inefficiency.
Saturation Index (SI): temperature, calcium hardness concentration, total alkalinity and pH represent the
main factors influencing scale formation. The tendency of water to either form scale or corrode is indicated by
the Saturation Index (SI):
SI = pH+TF+CF+AF-12.1
*Where: TF = Temperature Factor; CF = Calcium Hardness Factor; AF = Total Alkalinity Factor
SPA WATER CHEMISTRY AND BALANCE
Water Temperature TF Calcium
Hardness (ppm) CF Total Alkalinity (ppm) AF
(ºC) (ºF)
8 46 0.2 75 1.5 50 1.7
12 54 0.3 100 1.6 75 1.9
16 61 0.4 150 1.8 100 2.0
19 66 0.5 200 1.9 150 2.2
24 75 0.6 250 2.0 200 2.3
29 84 0.7 300 2.1 300 2.5
34 93 0.8 400 2.2 400 2.6
40 104 0.9 500 2.3 -- --
-- -- -- 1000 2.6 -- --
Test the water pH, Temperature, Calcium Hardness and Total Alkalinity levels. Use the equivalent Factors in
the SI equation.
SI = 0, Balance
If SI > 0, Scaling or cloudy water condition.
If SI < 0, Corrosive to metals or eye & skin irritating condition.
The SI is considered satisfactory if the value is within -0.3 to +0.3 range. Zero being perfect.

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 15
SPA WATER CHEMISTRY AND BALANCE (continued)
SPA Water Adjustment
How to adjust the spa water chemistry when the levels are off the range. CAUTION: Always follow the
chemical manufacturer’s directions, and the health and hazard warnings.
Total Alkalinity (TA) Adjustment
Remove the spa cover to aerate the water and use the included test strips to check the chemistry level.
Ensure the chlorine level in the water is between 2-4 ppm first, as chlorine will affect the TA test result.
If the TA level (and not the pH) is higher than 120 ppm, to lower the TA level, you add muriatic acid (hydrochloric
acid) or sodium bisulfate.
If the TA level is lower than 60 ppm, you add sodium bicarbonate.
For example, if the TA level is 180 ppm, the desired decrease is 60 ppm, from below chart, you need to add
0.269 Lb (121 g) of sodium bisulfate or 0.101 qt (96 ml) of muriatic acid.
If the test strip color is between 180 ppm and 240 ppm, and close to 180 ppm, you can also add 0.269 Lb
(121 g) of sodium bisulfate or 0.101 qt (96 ml) of muriatic acid.
If the reading is more than 240 ppm, you can add sodium bisulfate or muriatic acid to the water drop by drop
until the test strip indicates a 240 ppm reading, then add 0.528 Lb (238 g) of sodium bisulfate or 0.202 qt
(192 ml) of muriatic acid.
NOTE: After adjustment, retest the water after 24 hours and adjust again if necessary.
Desired level 60 ppm 80 ppm 100 ppm 120 ppm 140 ppm
Volume:
210 gal / 800 L
0.269 Lb 0.358 Lb 0.448 Lb 0.528 Lb 0.627 Lb
121 g 161 g 202 g 238 g 283 g
Lowering Total Alkalinity
Amount of Sodium Bisulfate to lower Total Alkalinity
Desired level 20 ppm 40 ppm 60 ppm 80 ppm
Volume:
210 gal / 800 L
0.059 Lb 0.118 Lb 0.178 Lb 0.237 Lb
27 g 53 g 80 g 107 g
Raising Total Alkalinity
Amount of Sodium Bicarbonate to raise Total Alkalinity
Desired level 60 ppm 80 ppm 100 ppm 120 ppm 140 ppm
Volume:
210 gal / 800 L
0.101 qt 0.135 qt 0.169 qt 0.202 qt 0.234 qt
96 mL 128 mL 160 mL 192 mL 223 mL
Amount of Muriatic Acid to lower Total Alkalinity
(Muriatic acid: 31.45%)
pH Adjustment
After the total alkalinity has been lowered to 120 ppm or raised to 80ppm and the pH is still high or low, you
can adjust it using the following chart.

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 16
SPA WATER CHEMISTRY AND BALANCE (continued)
Volume Total Alkalinity From→To
8.4→7.2 7.8→7.2
210 gal
(800 L)
120 ppm 0.028 qt 0.019 qt
26 mL 18 mL
80 ppm 0.018 qt 0.013 qt
18 mL 12 mL
Lowering pH
Lowering pH Using Muriatic Acid
Volume Total Alkalinity From→To
8.4→7.2 7.8→7.2
210 gal
(800 L)
120 ppm 0.071 Lb 0.047 Lb
32 g 21 g
80 ppm 0.047 Lb 0.032 Lb
21 g 14 g
Lowering pH Using Sodium Bisulfate
Calcium Hardness Adjustment
Use the included test strips to check the water hardness level and adjust it following below chart.
Lowering Calcium Hardness
If your household water supply is treated with a softener, mix the spa hard water with the soft water
according to the water volume ratio chart to lower the calcium hardness:
Initial level 1000 ppm 500 ppm 350 ppm 250 ppm
Desired level:
100 ppm
Water Volume Ratio (Vhard water:Vsoft water)
1:9 1:4 2:5 2:3
Lowering Calcium Hardness Using Soft Water
Volume Total Alkalinity From→To
6.8→7.2
210 gal
(800 L)
120 ppm 0.541 Lb
243 g
80 ppm 0.361 Lb
163 g
Raising pH
Raising pH Using Sodium Bicarbonate
Raising Calcium Hardness
If the calcium hardness level in the spa water is lower than 100 ppm, add 89 g or 0.197 Lb of calcium
chloride into the spa water.
WARNING
Muriatic acid is a caustic chemical and liquid solution of sodium bisulfate (NaHSO4)
is highly acidic. Handle all chemicals with care and wear extra personnel protective
equipment including goggle and gloves. It is very important not to splash acid onto
your skin or clothing, or into your eyes.

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Spa Tub Drainage
1. Turn off the spa control unit.
2. Connect the drain valve adaptor to a garden hose and point the other end
of the garden hose to a suitable draining area (see drawing 14).
3. Remove the drain valve cap from outside of the spa tub and attach the
drain valve adaptor to the drain valve (see drawing 14).
4. From inside of the spa tub, open the drain valve cap, water will start
flowing out from the garden hose.
5. When the water stops draining, disconnect the spa control unit from
the spa tub wall. Lift the spa tub wall from the side opposite the drain,
leading any remaining water to the drain and emptying the spa completely
(see drawing 15).
6. Attached the inflation hose (7) to the air blower inflation outlet on the
control unit.
7. Turn on the spa and press the button, aim the inflation hose at the
inlet/outlets on the spa tub and spa control unit to dry out any water in the
piping system
(see drawings 16 & 17).
8. Use a clean towel to wipe up any remaining water and moisture on the
spa tub and spa control unit.
9. Ensure the spa tub and spa control unit are thoroughly dried.
NOTE: The enclosed plugs (15) can be used to cover the water inlet and
outlet connectors from the inside of the spa tub to prevent water from
flowing out.
Spa Tub Cleaning
If dirt is visible in the water or water becomes cloudy and proper water
chemistry does not clear it up, change the water and clean the spa tub.
See “Spa Tub Drainage” section on how to drain the spa.
While empty, remove the cartridge housing from inside of the spa tub wall,
clean and/or replace the filter cartridge. Use a sponge and mild soap solution
to wipe away any soil or stains on the inside of the spa wall. Rinse thoroughly
before refilling with clean water.
IMPORTANT: Do not use steel wool, hard brushes or abrasive cleaners.
Spa Tub Air Valve Fastening
Check the spa tub air valve for leakage and tightness before use. If air is leaking
from the air valve, use the provided wrench (22) to tighten the air valve as follow:
1. Make sure the spa tub is deflated, open the air valve cap and insert the
wrench
(22) into the air valve body (see drawing 18).
2. With one hand, hold the backside of the air valve base from the inside of
the spa tub wall and turn the wrench (22) clockwise.
IMPORTANT: Never adjust the air valve base when the spa is in use or
filled with water. Only use the air valve wrench if the air valve is loose or
there is leakage around air valve base. Do not over tighten the air valve: over tightening can damage the
valve. Just ensure the air valve is snug and not leaking.
Spa Cover
The attachment buckles of the cover are locking buckles. Two keys are provided in the plastic bag with the
manual and other accessories. Each buckle is marked with “locked” and “unlocked” symbols for easy operation:
put the key into the slot on the buckle and turn it to the appropriate position to lock or unlock the buckle
respectively.
To assure safety from unauthorized access, always put the cover on when spa is not in use and lock all buckles.
Always keep the keys out of reach of children. In case you misplace the keys, you can use any similar size flat
screwdriver to lock or unlock the buckles.
Inspect the spa cover regularly for leaks, premature wear and tear, damage, or signs of deterioration. Never use
a worn or damaged cover: it will not provide the level of protection required to prevent unsupervised access to
the spa by a child.
MAINTENANCE
Page 17
14
1
2
3
11
18
22
15
16
17
7
7

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
Page 18
MAINTENANCE (continued)
1. Drain and clean the spa following the “Spa Tub Drainage” and “Spa Tub Cleaning” sections.
2. Reverse set up instructions to deflate and disassemble the spa tub, spa control unit and spa cover air
bladder.
3. To deflate the tub and the cover air bladder:
a) Open the deflation outlet cap (28) with the included bolt
wrench
(6) (see drawing 19).
b) Insert deflation hose adaptor (29) into the deflation outlet.
c) Insert inflation hose (7) over the deflation hose adaptor (29).
d) Insert the other end of the inflation hose into the tub air valve
or cover air bladder valve.
e) Press the air bubble button to deflate.
f) When deflation is completed reverse above steps and
ensures the deflation outlet cap (28) is securely fastened.
Caution: Only use for the purpose described in this manual.
Keep the inflation hose away from water or small objects when the
deflation function is activated to avoid damage to the blower motor.
4. Make sure all the spa components and accessories are
thoroughly clean and dry before storage. Air-dry the spa tub in
the sun for an hour before folding.
5. Fold the spa tub loosely and avoid any sharp corners to prevent
damage or leakage to the spa tub liner.
6. Prepare additional new cartridges for next time use.
7. Store the spa tub and accessories in a dry, temperature controlled, between 32º – 104 ºF (0º – 40ºC),
storage location.
8. The original packing can be used for storage.
STORAGE
Spa Tub and Cover Air Bladder Repair
Use the enclosed repair patch to repair any puncture:
• Clean and dry the area to be repaired thoroughly.
• Remove the patch backing paper and press patch firmly over the puncture.
Smooth out the surface to remove any air bubbles under the patch.
IMPORTANT
The ambient temperatures of air have an effect on the spa tub internal pressure. Air inside of the
spa tub may expand and contract with varying temperature leading to reduce pressure inside
of the spa tub. If this occurs, simply use the provided pressure gauge to check the internal air
pressure and add more air if necessary.
19
6
7
29
1
2
3
28

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
TROUBLESHOOTING
Page 19
NO DISPLAY/SPA
CONTROL UNIT DOES
NOT WORK
HOUSEHOLD CIRCUIT
BREAKER TRIPPED
NOT HEATING
PROPERLY
BUBBLE AIR BLOWER
DOES NOT WORK
FILTRATION PUMP
NOT WORKING
WATER NOT CLEAN
PUMP CONNECTORS
ARE NOT LEVEL WITH
THE SPA CONNECTORS
TUB HAS A STRANGE
SHAPE
TUB LOSES AIR
PRESSURE
LEAKING BETWEEN SPA
TUB CONNECTORS AND
CONTROL UNIT CON-
NECTORS
SPA IS TOO NOISY IN
FILTRATION MODE ONLY
• Spa is unplugged or off.
• Control panel cable plug loose.
• Power failure.
• GFCI/RCD tripped.
• GFCI/RCD broken.
• Circuit breaker under rated.
• Overloaded circuit breaker.
• An electrical fault in the line.
• Temperature set too low.
• Dirty filter cartridge.
• Water temperature decreasing during
heater STANDBY mode.
• Heating element failed.
• Air blower pump is too hot.
• Dirty filter cartridge.
• Filtration inlet and/or outlet clogged.
• Filter pump motor failed.
• Cartridge assembly not properly attached.
• Insufficient filtering time.
• Dirty filter cartridge.
• Improper water maintenance.
• Filtration inlet and outlet clogged.
• One characteristic of PVC is that
it changes shape, which is normal.
• Expanded internal air pressure by
strong sunshine.
• Air valve cap loose.
• Air valve base loose.
• Hole, cut or split on spa tub.
• Spa control base inlet/outlet connections
not securely tight.
• Spa control base inlet/outlet o-ring
missing/dirty.
• Control base components not securely
attached.
• Control base ground not level and firm.
• Spa filter motor failed.
• Ensure the spa is plugged and switched on.
• Ensure the control panel cable plug is firmly
attached to the control base receptacle.
• Check power source.
•Reset the GFCI/RCD.
•Contact Intex Service Center.
• Ensure correct circuit breaker rating.
• Provide a dedicated circuit breaker feeding the
spa electrical outlet only.
• Contact a qualify electrician to correct the
electrical fault.
• Increase the temperature and attach the spa
cover.
•Clean or replace the filter cartridge in time.
•If heater is in STANDBY mode, press the flame button
twice to heat up the water to the set temperature.
•Contact Intex Service Center.
•Turn off and unplug the spa. Let it cool down and
restart all over again.
•If problem persists contact Intex Service Center.
•Clean or replace the filter cartridge in time.
•Check and clean filtration inlet and outlet regularly.
•Contact Intex Service Center.
• Ensure the cartridge assembly is properly attached.
• Increase filtration time.
•Clean or replace the filter cartridge in time.
•Keep the spa water properly sanitized. Refer to the
chemical manufacturer’s instructions.
• Check and clean filtration inlet and outlet regularly.
• Elevate the pump with wood or another type of
insulated material to bring the pump’s connectors
level with the spa’s connectors.
• Do not expose the product under direct sunshine.
• Check the air pressure and release air if necessary.
During very hot weather, you must check to see
whether it is necessary to release some air. This is
to avoid any possible damage to the tub.
• Ensure air valve cap is securely closed.
• Fill up the spa tub with air then make sure the
air valve base is tighten, see “Spa Tub Air Valve
Fastening” section.
• Put liquid soap and water in a squirt bottle and spray on
seams. If there is a leak it will bubble. After you find the leak,
clean and dry the leaking area, then apply the repair patch
that comes with your spa.
• Tighten inlet and outlet connections.
• Coat the o-ring with petroleum jelly for water proof.
• Remove grid from inside spa with a screwdriver,
ensure inlet/outlet O-ring is in place, clean and not
damaged.
• Ensure control panel, back cover and all inlet/outlet
are securely connected.
• Ensure ground is level, firm and smooth.
• Replace the failed filter motor with a new one.
PROBLEM CAUSE SOLUTION

263
PO
SAVE THESE INSTRUCTIONS
(263PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 07/16/2014
English
WARRANTY
Your PureSpa has been manufactured using the highest quality materials and workmanship.
All Intex products have been inspected and found free of defects prior to leaving the factory.
This Limited Warranty applies only to the PureSpa listed below.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of purchase
will be required and must accompany warranty claims or the Limited Warranty is invalid.
PureSpa Warranty – 1 Year
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in the separate “Authorized Service Centers” sheet.
The Service Center will determine the validity of the claim. If the Service Center directs
you to return the product, please carefully package the product and send with shipping and
insurance prepaid to the Service Center. Upon receipt of the returned product, the Intex
Service Center will inspect the item and determine the validity of the claim. If the provisions
of this warranty cover the item, the item will be repaired or replaced at no charge.
Any and all disputes regarding the provisions of this Limited Warranty shall be brought before
an informal dispute settlement board and unless and until the provisions of these paragraphs
are carried forth, no civil action may be instituted. The methods and procedures of this
settlement board shall be subject to the rules and regulations set forth by the Federal Trade
Commission (F.T.C.). IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS
WARRANTY AND IN NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR
EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR
CONSEQUENTIAL DAMAGES OR LIABILITIES. Some states, or jurisdictions do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This Limited Warranty does not apply if the products are subject to negligence, abnormal use
or operation, accident, improper operation, improper voltage or current contrary to operating
instructions, or to damage by circumstances beyond Intex’s control, including but not limited
to, ordinary wear and tear and damage caused by exposure to fire, flood, freezing, rain, or
other external environmental forces. This Limited Warranty applies only to those parts and
components sold by Intex. The Limited Warranty does not cover unauthorized alterations,
repairs or disassembly by anyone other than Intex Service Center personnel.
DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN
OR REPLACEMENT. IF YOU ARE MISSING PARTS OR NEED
ASSISTANCE, PLEASE CALL US TOLL-FREE (FOR U.S. AND
CANADIAN RESIDENTS): 1-800-234-6839 OR VISIT OUR WEBSITE:
WWW.INTEXSTORE.COM.
Proof of Purchase must accompany all returns or the warranty claim will be invalid.
Page 20