Intuicom RTK Bridge-M User manual

Intuicom, Inc.
4900 Nautilus Ct. Ste. 100
Boulder, CO 80301
[phone]
www.intuicom.com
Intuicom®
RTK Bridge™-M Installation Guide
For
Trimble®EZ Guide 500®

Version 1.3 1 Intuicom, Inc.
This Document is for internal use by Intuicom Employees or by Resellers and Distributors who
are authorized and/or licensed to install Intuicom products. No part of this document may be
reproduced or transmitted in any form or by any means, electronic or mechanical, or for any
purpose without the express written permission of Intuicom Inc.
© 2011-2012 Intuicom Incorporated. All rights reserved.
Intuicom reserves the right to make changes to this document without notice. Unless otherwise
agreed to in writing, Intuicom assumes no responsibility or liability for the use of this document
or for the infringement of any copyright or other proprietary right and Intuicom shall deem
nothing contained in this document a warranty or guarantee.
Intuicom is a registered trademark of Intuicom, Inc.
Other product names mentioned in this guide may be copyrights, trademarks, or registered
trademarks of their respective companies and are hereby acknowledged.

Section 1: Installation Requirements
Version 1.3 2 Intuicom, Inc.
Overview
The EZ Guide 500 receiver is typically configured to accept CMR format RTK corrections from
an Intuicom RTK Bridge™-M which in turn has been configured to connect to a GPS/GNSS
reference network. The intended audience for this document is a dealer or integrator familiar
with the EZ Guide 500 and generally familiar with the Intuicom RTK Bridge-M. The Intuicom
RTK Bridge-M User Guide covers the steps necessary for its configuration.
1 Requirements for Installation
1.1 Required Information
In order to operate an Intuicom RTK Bridge-M, you are required to have the necessary
information to access and log in to the Real-Time Network. This information is entered
into the RTK Bridge-M and stored in a profile. More details on setting up an RTK
Bridge-M are available in the RTK Bridge-M manual.
IP address
TCP port
NTRIP mountpoint name
username and password for access to the real-time GPS/GNSS network
1.2 Required Equipment
1.2.1 Intuicom Equipment and Accessories
1. Intuicom RTK Bridge-M with activated data provider account (Verizon, AT&T, etc…)
2. Intuicom RTK Bridge-M to EZ Guide 500 data/power cable:
[P/N: FIP4-MRTKPWDT-EZ)
3. Intuicom RTK Bridge-M Cellular/GPS antenna/cable:
[P/N: FIP4- FIP4-MMDM-MAX (magnetic mount)]
1.2.2 Other Equipment and Accessories
4. Trimble EZ Guide 500 receiver with RTK (CMR) option enabled and COM port
available

Section 2: Installation Instructions
Version 1.3 3 Intuicom, Inc.
2 Installation Instructions
Below is the Installation Diagram for the recommended installation of the Intuicom RTK
Bridge-M Utilizing the equipment noted above.
Diagram 1
2.1 Configuration
Configure the Intuicom RTK Bridge–M to connect to GPS/GNSS Reference network
and obtain CMR/CMR+ correction data stream from an appropriate single reference
station, or as a VRS.
Configure the resulting RTK correction data to be output at a known baud rate (a
baud rate of 38400 is recommended).
Confirm GPS and cellular antenna (typically a combined antenna with two coaxial
cables with TNC connectors) are connected and placed where they have good sky
view and good cellular signal.
Independently confirm the RTK correction data stream from the data port on the front
of the unit. This can be accomplished by viewing data output from the data port into
any terminal emulation software (ie. HyperTerminal) and RTK Bridge–M
Programming Cable. Details can be found in the Intuicom RTK Bridge-M User
Guide.
Using the Intuicom RTK Bridge-M to EZ Guide 500 data/power cable, connect the
RTK Bridge-M to the COM Port on the EZ Guide 500.

Section 2: Installation Instructions
Version 1.3 4 Intuicom, Inc.
Select the Tools window
Go to GPS Setup

Section 2: Installation Instructions
Version 1.3 5 Intuicom, Inc.
Select Correction Source: RTK
Select Correction Delivery: Generic CMR Radio

Section 2: Installation Instructions
Version 1.3 6 Intuicom, Inc.
Configure Port Settings:
oBaud Rate 38400bps
oData Parity None
oStop Bits 1
Confirm operation –Confirm the Intuicom RTK Bridge-M is correctly configured
and its antennas are connected and within cellular coverage. The main status view on
the EZ Guide 500 should report that it is receiving RTK corrections.
You have now demonstrated that the EZ Guide 500 is receiving corrections and fixing
position.

Section 3: Operation
Version 1.3 7 Intuicom, Inc.
3 Sending GPS position from the EZ Guide 500 to the RTK
Bridge-M
Below is a description of how to configure the RTK Bridge–M and EZ Guide 500 to use the GPS
position from the EZ Guide 500.
3.1 RTK Bridge-M setup
The RTK Bridge-M must be configured to receive the GPS position from the data port. In
the Profile Configuration menu, select ‘Positioning,’ the RTK Bridge-M will display the
Positioning Sub-Menu. Press ‘1’ until positioning type is ‘DATA PORT.’ The RTK Bridge-
M is now ready to receive the GPS position from the EZ Guide 500.
3.2 EZ Guide 500 setup
There are several settings that must be configured on the EZ Guide 500 to send the GGA
string to the RTK Bridge–M.

Section 3: Operation
Version 1.3 8 Intuicom, Inc.
From the main screen, go to the Tools menu
Select User Mode Advanced

Section 3: Operation
Version 1.3 9 Intuicom, Inc.
Select System, then GPS
Select NMEA Output