inVue High Security 200 User manual

High Security 200
Handheld & Tablet Power-Up + Alarm Installation
MP602

2 3
Read entire instruction guide before starting installation.
System Components
1. HS200 Alarming Recoiler (MP602)
2. Handheld Alarm Unit (MP100) or Tablet Alarm Unit
(MP101)
3. HS200 Handheld or Tablet Sensor
4. Puck (MP217, MP218)
5. IR Dot (MP207)
6. 18V Power Supply
7. IR Key (not included)
System Overview
HS200 is designed to provide high security for high risk
environments. This system provides tough mechanical
security combined with alarming security and regulated
device power-up ability.
5
10
20
30
Drill Multi Tool
AF6313
18V Power Supply
PS18VUS
PS18VEU
PS18VAUS
PS18VUK
PS18VARG
Alarm Unit
MP100
MP101
HS200
Alarming
Recoiler
MP602
IR Dot
MP207
Puck
MP217
MP218
Sensor
MP609
MP610
MP611
MP612
MP613
MP614
T-20 Bit
(included with
Multi Tool)
T-27 Bit
(included with
Multi Tool)

4 5
Drill a 45 mm (1.75”) diameter hole in display
counter.
1
RECOILER & PUCK INSTALLATION
5
10
20
30
Puck
Spacer
(For display counters
between 3.175 mm, 0.125”
and 12.7 mm, 0.5” thick.)
Recoiler

6 7
Slide recoiler up through hole in display counter. Use
spacer if needed. Loosely hand tighten cap above
counter onto recoiler.
2a
Recoiler
Spacer
(For display counters
between 3.175 mm, 0.125”
and 12.7 mm, 0.5” thick.)
Cap
2bRotate recoiler until cut out in recoiler is towards back
of display counter. Fully tighten cap.
Back of
display
counter
Cut out in
recoiler
Recoiler
Front of
display
counter

8 9
Pull recoiler up and slide both parts of puck together
on cap. Confirm lock is at back of display counter.
3aFully tighten screws on puck with T-20 bit. 3b
Back of
display
counter
Front of
display
counter

10 11
ALARM & IR DOT INSTALLATION
Alarm Unit
IR Dot
1Drill a 20.5 mm (0.8125”) diameter hole in display
counter at preferred location for IR Dot.
5
10
20
30

12 13
2Slide IR dot through display counter and tighten
nut below counter.
3Plug cord from recoiler and IR dot into alarm unit.

14 15
Remove clear film from Alarm Unit. Attach Alarm Unit
below counter near puck. Press firmly for at least 10
seconds.
4 5 Plug cord from alarm unit into power supply. Plug
power supply into outlet.

16 17
ATTACHING MERCHANDISE
Sensor
Arms
Power
Connector
Wipe back of phone with alcohol wipe provided. Let it
dry completely.
1
CONTENTS: One pad saturated in
Isopropyl Alcohol
75%
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE

18 19
Plug power connector into phone.
2 3
Top of Phone
Confirm phone is placed on sensor correctly so orien-
tation of phone is correct on recoiler. Make sure cut out
in sensor is towards top of phone.
Cut out in
sensor

20 21
4Remove clear film off adhesives on sensor. Center and
attach merchandise to sensor. Press firmly for at least
10 seconds.
5Attach both arms to sensor. Confirm arms are fitted
to width of merchandise. Squeeze both arms against
merchandise and tighten screw with T-20 bit to lock
arms in sensor.

22 23
6Adjust arms to thickness of merchandise and tighten
screw with T-20 bit. Do not overtighten.
7Attach sensor to recoiler.

24 25
8Fully tighten both screws with T-20 bit. 9Optional. Lock screw with T-27 bit to prevent from
lifting recoiler.

26
Place key on lens of IR Dot.
Press grey button once to
arm and disarm alarm.
Arm/Disarm Alarm

© 2013 InVue Security Products Inc. All rights reserved.
InVue is a registered trademark of InVue Security Products.
SD0145 Rev0 03/06/13
www.invuesecurity.com
Corporate Office (North America) // 704.752.6513 •888.55.INVUE
Europe, Middle East & Africa // +31.23.8900150
Asia Pacific // +65.6766.4844
Latin America // +52.55.9000.3957